Ditec IP2269 Entrematic ZEN 2C Remote Control
Factory default channel configuration
Manual configuration
Configuration with PC
Refer to Ditec ZEN Manager system documentation.
- Last version of this manual
Specification
| Transmitters | Frequency | Radiated power | Type | Power supply | Channels | Range |
| ZEN2** | 433,92MHz | < 1mW | Rolling code | Battery type CR2032 | 2 | 50-150m |
| ZEN4*** | 4 | |||||
| ZEN2C | Fixed code | 2 | ||||
| ZEN4C | 4 | |||||
| ZENP2 / ZENP2MT | 868,35MHz | < 1mW | AES-128 rolling code |  Use batteries of indicated type. | 2 | |
| ZENP4 / ZENP4MT | 4 |
[***] Models ZEN4, ZEN4W, ZEN4MT
WARNING: Product contains coin/button cell battery
- Keep product and batteries away from children
- Battery can cause severe or fatal injuries in 2 hours or less if swallower or placed inside any part of the body
- Seek immediate medical attention if it is suspected that a coin/button cell battery has been swallowed or placed inside any part of the body.
All models
[A] Direct programming
- Activate Receiver Learning mode (refer to specific product manual)
- Press button on NEW TX
- Wait
[B] Battery save function enable-disable
- Press simultaneously
Factory enabled in all models
Do not use remote controls to perform hold-to-run operations - Enable
Disable
[C] Encoding type check
- Keep pressed button to be checked
N Encoding 0 Fixed code 1 “Dip-switch” 2 Rolling code 3 “MM53200” clone 4 AES 5 Protected Battery save function must be enabled
[D] Battery replacement
- Open housing
- Take out battery
- Insert new battery
Only models ZEN2C-ZEN4C
[E] Factory RESET
- Take out battery
- Keep pressed buttons as shown
- Keeping buttons pressed re-insert battery
[F] Existing TX full duplication
- With NEW TX
Also compatible with: BIXLS2 - With EXISTING TX, within 10s
[G] manual code setting
- With NEW TX
Example:
Code 0 1 0 0 1 0 0 1 0 0
- Insert sequence of ten “0” or “1” Confirmation blinks:
- With NEW TX
- Again with NEW TX, within 10s
- Press and release button on NEW T on which duplicate generic TX (example)
- Within 10s press desired button on generic TX
Compatible with 433MHz products with “MM53200” encoding or similar
Only models ZEN (2/2B/2G/2R/2W/2Y/2MT/4/4W/4MT)
[I] Add NEW TX by existing TX
- Go near the gate
- With EXISTING (programmed) TX
- Again with EXISTING TX
- With NEW TX, within 10s
- Wait
[J] Enable-disable AES encryption
- Take out battery
- Keep pressed button as shown
Case a) buttons 1 / 1-2
Case b) buttons 2 / 3-4
- With button pressed re-insert battery
AES enabled-disabled on the indicated buttons
Mode verification
The procedure toggles AES mode (ON-OFF-ON-OFF…). AES decoder available only on new generation receivers or control units – refer to specific product manual
EC and UK Declaration of Conformity
The manufacturer, ASSA ABLOY Entrance Systems AB, with registered office at Lodjursgatan 10, SE-261 44 Landskrona, Sweden declares that the type of radio equipment ZEN2/ZEN2B/ ZEN2C/ZEN2G/ZEN2R/ZEN2W/ZEN2Y/ZEN2MT/ZEN4/ZEN4C/ZEN4W/ ZEN4MT/ZENP2/ZENP2MT/ZENP4/ZENP4MT complies with:
EC Directive
RED Directive 2014/53/UE
UK Regulations
Radio Equipment Regulations 2017
The crossed-out wheeled bin symbol indicates that the product should be disposed of separately from household waste. The product should be handed in for recycling in accordance with local environmental regulations for waste disposal.
By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or landfill and minimize any potential negative impact on human health and the environment.
Technical data subject to change without notice
ASSA ABLOY Entrance Systems AB
Lodjursgatan 10
SE-261 44, Landskrona
Sweden
© ASSA ABLOY
Documents / Resources
 | Ditec IP2269 Entrematic ZEN 2C Remote Control [pdf] User Manual IP2269, Entrematic ZEN 2C Remote Control, ZEN 2C Remote Control, Entrematic Remote Control, Remote Control, Entrematic ZEN 2C, Control |
