Dioche A7 Stand Alone Access Control and Reader
INTRODUCTION
This product is a Keypad standalone access control. 1500 user capacity and supporting 13.56MHz Mifare card (UID 7 bytes, 4 byets, Plus). It can be access by card, PIN, card + PIN. It also equipped with admin add/delete cards, door detection, external alarm and Wiegand input/output interface.
Features and Benefits
- A7,A8 Zinc-alloy housing, A9 ABS shell
- Waterproof, conforms to IP67
- With Wiegand input & output, it can be used as not only
- standalone, but also slave reader or access controller.
- Equipped with admin cards, which can add/delete users quickly.
- Pulse Mode or Toggle Mode
- Door Bell button (A8,A9)
Specifications
| Operating Voltage | 10-24V DC |
| Idle Current | ≤45mA |
| Active Current | ≤80mA |
| Waterproof | IP67 |
| User Capacity | 1500 |
| Frequency | 13.56MHz |
| Card type | Mifare (UID 7 bytes, 4 byets, Plus) |
| Read Range | ≤6cm |
| Wiegand Interface | Card: Wiegand 26 bits or 34 bits, PIN: 4 bits |
| Lock Output Load | ≤2A |
| Alarm Output Load | ≤500mA |
Packing List
INSTALLATION
- Remove the back cover from the unit with screw.
- Drill hole on the wall according to the back size of the machine and fix the back cover on the wall.
- Thread the cable through cable hole, connect related cable. For the un-used cable please separate with insulating tape.
- After wiring, install front casing and fix the back cover well with screws.
Wiring
| Wire Color | Function | Notes |
| Orange | NC | Relay NC |
| Purple | COM | Relay COM |
| Blue | NO | Relay NO |
| Black | GND | Negative Pole |
| Red | DC+ | 10-24V DC Power Input |
| Yellow | OPEN | Request to Exit Button |
| Brown | D_IN | Door Contact |
| Grey | ALARM- | Alarm Negative |
| Green | D0 | Wiegand output/input Data0 |
| White | D1 | Wiegand output/input Data1 |
| Grey & Black | BELL | External BELL |
| Yellow & Black | BELL | External BELL |
Sound and Light Indication
| Operation Status | LED | Buzzer |
| Stand by Mode | Red light bright | |
| Enter program Mode | Red light shines | |
| In the Program Mode | Orange light bright | |
| Open lock | Green light bright | One beep |
| Operation failed | Three beeps |
Modify Admin Code
| Programming Step | Keystroke Combination | LED |
| Enter Program Mode | * (Admin Code) # (Factory default is 777777) | Red shines |
| Modify Admin Code | 0 (New Admin Code) # (Repeat New Admin Code) # | Orange bright |
| Exit Program Mode | * | Red bright |
Note: Admin should enter Program Mode, then the settings can be set or reset. For security, you must change the Admin Code and then keep in mind.
Factory Default Setting and Add Admin Cards
power off, press exit button , power on, release it until hear two beeps, then the red LED will be orange. It means the device is under the status of waiting for adding admin cards. Swiping two cards, the first card is “Admin Add Card”, the second card is “Admin Delete Card”, thenthe device will be in standby mode and the red light bright. Resets to factory default setting and adding admin cards are successful.
If you don’t need to add admin cards: Press “ ”* , power on, hold it for more than 10 seconds.
Note: Reset to factory default, the users’ information won’t be deleted.
STANDALONE MODE
Connection Diagram
Special Power Supply for Access Control
DC power Supply for Access Control
Note: The electric locks must be connected with diode(1N4004), otherwise the device might be damaged. The white end of the diode is connected to positive pole of electric lock and the other end is connected to negative pole of the electric lock.
Add/Delete Users by Admin Cards (in standby mode)
| Add users | Step 1: Read Admin Add Card Step 2: Read user cards (Repeat step 2 for additional user cards) Step 3: Read Admin Add Card again to end |
| Delete users | Step 1: Read Admin Delete Card) Step 2: Read user cards (Repeat step 2 for additional user cards) Step 3: Read Admin Delete Card again to end |
Enter and Exit Program Mode
| Programming Step | Keystroke Combination |
| Enter Program Mode | * (Admin Code) # (Factory default is 777777) |
| Exit Program Mode | * |
Add Users (ID number: 1-1500)
| Programming Step | Keystroke Combination | LED |
| Enter Program Mode | * (Admin Code) # | Red shines |
| Add Card User | ||
| Add Card: By Card OR Add Card: By ID number OR Add Card: By Card number | 1 (Read Card) #
1 (Input ID number) # (Read Card)
1 (Input 8/10 digits Card number)# |
Orange bright |
Documents / Resources
 | Dioche A7 Stand Alone Access Control and Reader [pdf] User Manual A7, Stand Alone Access Control and Reader, A7 Stand Alone Access Control and Reader, Access Control and Reader, Reader, A8, A9, A Series |
