Digital-Watchdog-logo

Digital Watchdog DWC-VFFMW Flush Mount Low Profile Vandal Dome IP Cameras

Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-product

Product Information

Flush mount for low-profile vandal dome IP cameras (DWC-VFFMW)

The flush mount for low-profile vandal dome IP cameras is a mounting accessory designed to securely and discreetly mount Digital Watchdog’s DWC-M(P)V8 cameras onto a surface. The mount has a low-profile, minimizing the visibility of the camera and reducing the risk of tampering. The mount includes a base, a 3-point in-ceiling wing, and mounting screws. The mount is compatible with specific DWC-M(P)V8 camera models and comes with a mounting template and a quick start guide for easy installation.

Usage Instructions

  1. Before installation, remove the magnetic cover from the flush mount.
  2. Use the mounting template to mark and drill the necessary holes in the mounting surface.
  3. Adjust the 3-point in-ceiling wing using a screwdriver. Twist the screws to tighten and expand until the flush mount is secured to the mounting surface.
  4. To mount the camera to the mounting accessory, remove the dome from the camera base using the wrench included with the camera.
    • (Note: Do not touch the lenses when handling the camera modules.)
  5. Pass wires through the flush mount base and make all necessary connections.
  6. Secure the camera to the flush mount using the appropriate mounting screws. Refer to the table below for screw size:
    Camera part numberMounting screw size
    DWC-MV82DiVT25mm mounting screws
    DWC-MV82WiATW, DWC-MPV82WiATW16mm mounting screws
    3-point ceiling wings
    DWC-MV85WiATW, DWC-MPV85WiATW16mm mounting screws
    Flush mount base
    DWC-MVC8WiATW, DWC-MPVC8WiATW16mm mounting screws
    Camera module
    DWC-MVC8Wi28TW, DWC-MPVC8Wi28TW25mm mounting screws
    Camera dome cover
  7. Adjust the camera’s position and angle. Secure the dome cover to the camera base using the screws included with the camera. See the camera’s quick start guide for more information.
  8. Complete the installation by reattaching the magnetic cover over the camera dome.

Note: For additional support materials and tools, visit http://www.digital-watchdog.com/resources and search for your product by entering the part number in the “Search by Product” search bar. All supported materials, including manuals and quick start guides (QSGs), will appear in the results.

WHAT’S IN THE BOX

 

Camera Mounting Screws for DWC-M(P)V8 Cameras (25mm)

 

Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-1

 

2

 

Quick Setup Guide

Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-3 

1

 

Camera Mounting Screws for DWC-M(P)VC Cameras (16mm)

Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-2

 

 

2

 

Mounting Template

Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-4 

1

INSTALLATION

  1. Before the installation, remove the magnetic cover from the flush mount.
  2. Using the mounting template mark and drill the necessary holes in the mounting surface.
  3. Adjust the 3-point in-ceiling wing using a screwdriver. Twist the screws to tighten and expand until the flush mount is secured to the mounting surface.
  4. To mount the camera to the mounting accessory, remove the dome from the camera base using the wrench included
    • NOTE: Do not touch the lenses when handling the camera modules.
  5. Pass wires through the flush mount base and make all necessary connections.Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-6 Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-7
  6. Secure the camera to the flush mount using the appropriate mounting screws. Refer to the table below:
    Camera part numberMounting screw size
    DWC-MV82DiVT

    DWC-MV82WiATW, DWC-MPV82WiATW DWC-MV85WiATW, DWC-MPV85WiATW

     

    25mm mounting screws

    DWC-MVC8WiATW, DWC-MPVC8WiATW DWC-MVC8Wi28TW, DWC-MPVC8Wi28TW16mm mounting screws
  7. Adjust the camera’s position and angle. Secure the dome cover to the camera base using the screws included with the camera. See the camera’s QSG for more information. Complete the installation by reattaching the magnetic cover over the camera dome.

CONTACT

Digital-Watchdog-DWC-VFFMW-Flush-Mount-Low-Profile-Vandal-Dome-IP-Cameras-fig-5

digital-watchdog.com

Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.

Documents / Resources

Digital Watchdog DWC-VFFMW Flush Mount Low Profile Vandal Dome IP Cameras [pdf] User Guide
DWC-VFFMW Flush Mount Low Profile Vandal Dome IP Cameras, DWC-VFFMW, Flush Mount Low Profile Vandal Dome IP Cameras, Vandal Dome IP Cameras, Dome IP Cameras

References

Leave a comment

Your email address will not be published. Required fields are marked *