DieseRC 5301 Wireless Remote Control Switch
Specifications
- Working voltage: DC 5V~30V
- Input/output voltage: 1~250V
- Output Type: Passive output
- Quiescent Current: 97dbm
- Max current: Not specified
- RF frequency: Not specified
- Working temperature: Not specified
- Receiving Sensitivity: Not specified
- Amount of storage remote controls: 20 pieces
- Support encoding: 1527 Leaning code, 2262 fixed code
- RF Operating mode: ASK superheterodyne wireless reception
- Receiving range: Open space is more than 50 meters
- Remote operating mode: Momentary Mode / Toggle Mode / Latched Mode / Delay Mod
RELAY REMOTE CONTROL SWITCH
PRODUCT INFORMATION
TYPE—-5301
| Technical Data | |
| Working voltage | DC 5V~30V |
| Input/output vlotage | 1~250V |
| Output Type | Passive output |
| Quiescent Current | <5MA |
| Max current | 10A |
| RF frequency | 433MHz |
| Working temperature | -30~+80 |
| Receiving Sensitivity | >97dbm |
| Amount of storage remote controls | 20 pieces |
| Support encoding | 1527 Leaning code、2262 fixed code |
| RF Operating mode | ASK super heterodyne wireless reception |
| Receiving range | Open space is more than 50 meters |
| Remote operating mode | Momentary Mode /Toggle Mode /Latched Mode /Delay Mode |
PRODUCT DETAIL
- NO: Normally open pin
- COM: Common pin
- NC: Normally closed pin
WIRING DIAGRAM
WIRING DIAGRAM
Warning
- Usually the receiver and transmitter have been paired with each other in factory. If not, please reprogram them.
- Reset before you want to change the operating mode.
- After reset, all the remote controls cannot work anymore.
- Replace the battery in time when the remote transmitter voltage is low. To get the stronger signal transmission.
- Slightly stretch the antenna on the receiver for better signal reception.
- The remote transmitter need to have 2 or more buttons, if you want to set up in latched mode.
- The output type is passive output / potential-free contacts.
Operating Mode
Momentary Mode
- Press and hold the button, relay will turn on;
- Release the button, this relay will turn off.
How to program
- Press the learning button (on the receiver) 1 time. The indicator LED on the receiver will light up;
- Press one button on the remote transmitter. The indicator LED on the receiver will flashing several times and then light down. Succeed.
Toggle Mode
- Press button “A”, relay will turn on;
- Press button “A” again, this relay will turn off.
How to program
- Press the learning button (on the receiver) 2 times. The indicator LED on the receiver will light up;
- Press one button on the remote transmitter. The indicator LED on the receiver will flashing several times and then light down. Succeed.
Latched mode:
- Press button “A”, relay will turn on;
- Press button “B”, this relay will turn off.
How to program
- Press the learning button (on the receiver) 3 times. The indicator LED on the receiver will light up;
- Press button “A” on the remote transmitter. The indicator LED on the receiver will flashing several times and then light up;
- Press button “B” on the remote transmitter. The indicator LED on the receiver will light down. Succeed.
Delay Mode:
Press and hold on the button, relay will turn on;
CUSTOMER SERVICE
- Work volts: DC5V~30V
- Max current: 10Amp
If there is any questions about the products,please contact us firstly. We will do our best to solve your problem.
Thank you.
- Huizhou Wenqiao Electronic Technology Co., Ltd.
- Address: 1203, Building T19, Fangzhilonghuwan, Sanhuan South Road, Huicheng District, Huizhou City, Guangdong Province, China 516000
- WhatsApp : +86 13502278583 / +86 18138805271
- Email : dieseelectronic@163.com
Documents / Resources
 | DieseRC 5301 Wireless Remote Control Switch [pdf] Instruction Manual 5301 Wireless Remote Control Switch, 5301, Wireless Remote Control Switch, Remote Control Switch, Control Switch, Switch |
