Delta-Children-Adley-3-in-1-Crib-User-Manual-logoDelta Children Adley 3 in-1 Crib User Manual

Delta-Children-Adley-3-in-1-Crib-User-Manual-product-2

Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE.

ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of reach of children until assembly is complete. THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. When contacting Delta Consumer Care please reference the above information. Before contacting Delta Consumer Care please ensure that the information above matches the information found on the label on the Crib End bottom rail, please reference the information found on the product when contacting Delta Consumer Care. To register your product for important safety alerts and updates to your product please visit www.DeltaChildren.com and click on Product Registration.

CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A THICKNESS NOT EXCEEDING 6 IN.

WARNING:

  •  Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an infant.
  •  Failure to follow these warnings and the assembly instructions could result in serious injury or death. DO NOT use this crib if you cannot exactly follow the accompanying instructions.
  •  To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
  •  Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
  •  Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
  •  Strangulation Hazard: Do not place crib near the window or patio door where cords from blinds or drapes may strangle a child.
  •  Fall Hazard: When a child is able to pull to a standing position, set mattress to the lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib has adjustable mattress support. For the convenience of the parent when the baby is very small, the mattress support may be used in the highest position. Important: with the mattress support and mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches higher than the top surface of the mattress. If it is not, lower the mattress support and the mattress to the next highest position.
  •  Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm), whichever occurs first. The child should be placed in youth or regular bed.
  •  Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. Do not use crib if any parts are missing, damaged or broken. Contact Delta Children’s Products for replacement parts and instructional literature if needed. Do not substitute parts.
  •  Follow warnings on all products in a crib.
  •  If refinishing, use a non-toxic finish specified for children’s products.
  •  Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
  •  Infants can suffocate in gaps between crib sides and a mattress that is too small.
  •  Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that every component is properly and securely in place.
  •  To avoid head injury, do not allow any child to play underneath the crib.
  •  Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
  •  In Canada Only – Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or who is taller than 90 cm.

TODDLER BED

INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and between bed parts can entrap head and neck of a small child. NEVER use bed with children younger than 15 months. ALWAYS follow assembly instructions. The maximum user weight is 50lbs (22.7kg)

STRANGULATION HAZARD
NEVER place a bed near windows where cords from blinds or drapes may strangle a child. NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords, around a child’s neck. These items may catch on bed parts.

ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width, and 4 in (100mm) in thickness. The mattress thickness must not exceed 6 in (150mm).

NOTES ON ASSEMBLY

  •  During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn in actual size and design. Be sure to use the proper size and shape specified in the instructions.
  •  To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON USE
Keep children and others safe by following these simple rules:

  •  Do not allow any child to play on the furniture
  •  Do not allow climbing on any piece of furniture.
  •  Do not allow hanging from any piece of furniture.
  •  Always monitor your child’s activity when in the nursery.

NOTES ON CARE AND MAINTENANCE

  • Do not scratch or chip the finish.
  •  Inspect the product periodically, and contact Delta Children’s Products for replacement parts or questions.
  •  Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement. These extremes can cause a loss of structural integrity.
  •  To preserve the luster of the high-quality finish on your product, it is recommended to place a doily or felt pad under any items you place on the finish.
  •  Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
  •  Do not use abrasive chemicals.
  •  Do not spray cleaners directly onto the furniture.
  •  Lift slightly when moving on carpeting to prevent leg breakage.
  •  The use of a vaporizer near furniture will cause wood to swell and finish to peel.

PARTS

MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. HARDWARE KIT PART #23359 FOR COLOR 100 OR #23360 FOR COLOR 260 OR #23361 FOR COLOR 604 AND 645. SEE THE FRONT COVER.

POUCH ATTACHED TO MATTRESS SUPPORT- KEEP INSTRUCTIONS IN THIS POUCH AFTER ASSEMBLY. WARNINGS RELATED TO THE SAFE USE OF THIS CRIB ARE PRINTED ON THE POUCH

Section 1: Crib Assembly

Step 1

Parts and tools required to complete the step. Attach (1) Left Crib End (Part B) to (1) Left Crib Post (Part D) and (1) Right Crib Post (Part E) using (2) Φ4×30 mm Metal Pins (Part P), (2) M6x55mm Bolts (Part K) and (2) M6x17mm Barrel Nuts (Part N). Tighten with the M4 Allen Wrench. Use the flat head screwdriver to hold the barrel nut in the proper alignment.
Repeat on the Right Crib End (Part C).

Section 1: Crib Assembly
Step 2

Parts and tools required to complete the step.Insert the slot of the Crib End Top (Part A) into the tenon on top of the Left Crib End (Part B), then insert the (2) M6x40mm Bolts (Part L), through the legs into the metal inserts on the Crib End Top (Part A) as shown. Repeat on the Right Crib End.

Section 1: Crib Assembly
Step 3

Attach (1) Crib Side (Part F) to the assemblies from step 2 using (4) M6x75 mm Bolts (Part J) and (4) M6x17mm Barrel Nuts (Part N). Install only (1) Crib Side at this time, the other will be installed in Step 5. Tighten with the M4 Allen Wrench. Use the flat head screwdriver to hold the barrel nut in the proper alignment.

Section 1: Crib Assembly
Step 4

Attach the Mattress Support (Part H) in all corners using (1) M6x15 mm Bolt (Part M) in each corner. Tighten with the M4 Allen Wrench. The ! Warnings printed on the pouch attached to the mattress support must face up. This crib has (3) adjustment positions, use the highest only for new borns, and move the mattress down as the child grows.

WARNING:
Fall Hazard: When a child is able to pull to a standing position, set mattress to the lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out.

Section 1: Crib Assembly
Step 5

Attach (1) Crib Side (Part F) to the assembly from Step 4 using (4) M6x75mm Bolts (Part J) and (4) M6x17mm Barrel Nuts (Part N). Tighten with the M4 Allen Wrench. Use the flathead screwdriver to hold the barrel nut in the proper alignment.

Section 1: Crib Assembly
Step 6

Parts and tools required to complete step. Store the assembly instruction booklet in the pouch attached to the mattress support. Store all parts and tools separately, in a safe place.

WARNING:
SEE PAGE 2 FOR INFORMATION

Section 2: Toddler Bed Conversion
Step 1

Parts and tools required to complete the step. Remove the Side installed in Step 5 of Section 1 Crib Assembly. REMOVE ONLY ONE SIDE.

Section 2: Toddler Bed Conversion
Step 2

Attach the Stabilizer Bar (Part G) to the Assembly from Section 2 Step 1 using (2) M6x75mm Bolts (Part J) and (2) M6x 17mm Barrel Nuts (Part N). Tighten with the M4 Allen Wrench. Use the flathead screwdriver to hold the barrel nut in the proper alignment.

Section 2: Toddler Bed Conversion
Step 3

WARNING:
SEE PAGE 3 FOR TODDLER BED WARNINGS

The mattress support must be in the lowest position. Store all hardware safely. Read all warnings on page 3. As shown, use as a day bed or loveseat sofa. Do Not use without a stabilizer bar installed. A stabilizer bar must be used when converted to a toddler bed.

A toddler bed guardrail is available for this crib. Please see your crib retailer, visit www.DeltaChildren.com or contact Delta Consumer Care for more information. This crib uses Delta Style # 0080 Guardrail.

Consumer Care:www.DeltaChildren.com Delta Children’s Products
114 West 26th Street New York, NY 10001 Tele.212-645-9033

Warranty:
This Delta Crib is warranted to be free from defects for a period of 1 year from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift when the registration is on file with Delta. To register your product for important safety alerts and updates to your product please visit www.DeltaChildren.com Please do not return this item to the store before contacting us about missing parts or with any questions.To report a problem, please log on to www.DeltaChildren.com and click the Consumer Care Tab, or contact us by phone at (212) 645-9033. In the event that you need to contact our customer service department please have the Style Number and Lot Number available. Use the space below to make note of those numbers. They can be found on the label on the Crib End bottom rail.

STYLE No: 6412

  • Lot No. : _______________________
  • Pack Date:_____________________
  • Date of Purchase: _____________ (you should also keep your receipt)

Leave a comment

Your email address will not be published. Required fields are marked *