Einführung
Thank you for choosing the Hyuduo Smart Bidet Attachment. This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new bidet attachment. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product.
Produktkomponenten
Bitte stellen Sie vor Beginn der Installation sicher, dass alle Komponenten vorhanden sind:
- 1 x Bidet Toilet Attachment
- 1 x Tee Joint (with 1 washer)
- 1 x White Pipe
- 2 x Large Washers
- 1 x Englisch Bedienungsanleitung
Note: Please allow for minor discrepancies due to manual measurement.
Setup und Installation
Follow these steps to properly install your Hyuduo Smart Bidet Attachment:
- Wasserzufuhr abstellen: Locate the water supply valve for your toilet and turn it off completely. Flush the toilet to drain the tank.
- Toilettensitz entfernen: Lift the toilet seat and lid. Unscrew the bolts holding the toilet seat to the toilet bowl. Keep these bolts and nuts as they will be reused.
- Position Bidet-Aufsatz: Place the bidet attachment on the toilet bowl, aligning its adjustable brackets with the bolt holes. Adjust the brackets as needed to ensure a secure fit.
- Toilettensitz wieder anbringen: Place your toilet seat back on top of the bidet attachment and the toilet bowl. Secure it using the original bolts and nuts. Ensure the bidet attachment is firmly held in place.
Image: The Hyuduo bidet attachment shown installed beneath a standard toilet seat on a toilet bowl.
- Disconnect Toilet Supply Hose: Disconnect the flexible water supply hose from the toilet tank's fill valve. Have a towel ready to catch any residual water.
- Install Tee Joint: Connect the provided Tee Joint to the toilet tank's fill valve. Ensure the washer is correctly seated to prevent leaks.
- Wasserversorgung anschließen: Reconnect the flexible water supply hose to the bottom of the Tee Joint.
- Bidet-Schlauch anschließen: Connect one end of the white pipe (bidet hose) to the open port of the Tee Joint. Connect the other end of the white pipe to the water inlet on the bidet attachment. Use the large washers as needed to ensure a tight, leak-free connection.
- Wasserversorgung wiederherstellen: Slowly turn the main water supply valve back on. Check all connections for leaks. If leaks occur, tighten the connections.
Bild: Eine Nahaufnahme view of the bidet attachment's control panel, showing the water pressure dial.
Bedienungsanleitung
The Hyuduo Smart Bidet Attachment is designed for ease of use:
- Wasserdruck einstellen: Use the control dial located on the side of the bidet attachment to adjust the water pressure. Turn the dial from 'OFF' towards 'LOW' for a gentle spray, and further towards 'HIGH' for a stronger spray.
- Düsenposition: The bidet features an intelligent flushing device that automatically positions the nozzle for effective cleaning.
- Selbstreinigungsfunktion: The nozzle has a self-cleaning function. After each use, the nozzle automatically rinses itself to maintain hygiene.
Abbildung: Draufsicht view of the Hyuduo bidet attachment, highlighting its slim design and control knob.
Wartung
Regelmäßige Wartung gewährleistet optimale Leistung und Hygiene:
- Düsenreinigung: The bidet attachment includes an automatic self-cleaning function for the nozzle. For additional cleaning, you may gently wipe the nozzle with a soft cloth and mild soap solution when the water supply is off.
- Außenreinigung: Reinigen Sie die Außenseite des Bidet-Aufsatzes mit einem weichen, fusselfreien Tuch.amp Verwenden Sie ein Tuch und ein mildes, nicht scheuerndes Reinigungsmittel. Vermeiden Sie aggressive Chemikalien oder Scheuerschwämme, die die Oberfläche beschädigen könnten.
- Regelmäßige Inspektion: Periodically check all water connections for any signs of leaks or wear. Tighten connections if necessary.
Fehlerbehebung
If you encounter issues with your bidet attachment, refer to the following common problems and solutions:
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| No water spray or low pressure | Water supply valve is closed; hose kinked; clogged nozzle. | Ensure water supply valve is fully open. Check for kinks in the water hose. Gently clean the nozzle if visible debris is present. |
| Wasser tritt an den Anschlüssen aus. | Loose connections; missing or improperly seated washers. | Turn off water supply. Tighten all connections. Ensure washers are correctly installed and not damaged. Replace washers if necessary. |
| Nozzle does not extend or retract properly | Debris obstructing nozzle; internal mechanism issue. | Turn off water supply. Gently inspect the nozzle area for any obstructions and remove them. If the problem persists, contact customer support. |
Technische Daten
- Artikeltyp: Bidet-WC-Aufsatz
- Material: ABS
- Bruttogewicht: 850 g
- Paketabmessungen: 18.11 x 7.87 x 3.15 Zoll
- Modellnummer: Hyuduofcu7yo5thb-12
- Verbindungsgröße: 3/8 Zoll
Garantie und Support
For warranty information or technical support, please refer to the documentation included with your purchase or contact the retailer where the product was acquired. You may also visit the official Hyuduo webWebsite für weitere Unterstützung.