Benutzerhandbücher+

FIDECO Y-482H

FIDECO USB 3.0 Dual Bay HDD/SSD Docking Station (Model Y-482H) User Manual

Your guide to setting up and operating your FIDECO docking station.

1. Produktüberschreitungview

The FIDECO USB 3.0 Dual Bay HDD/SSD Docking Station (Model Y-482H) provides a convenient solution for connecting 2.5-inch and 3.5-inch SATA I/II/III hard drives and solid-state drives to your computer via USB 3.0. It also features an offline clone function, allowing you to duplicate drives without a computer connection.

Key features include high-speed data transfer up to 5Gbps, broad operating system compatibility, and a stable power supply for reliable operation.

FIDECO USB 3.0 Dual Bay HDD/SSD Docking Station

Image 1.1: FIDECO USB 3.0 Dual Bay HDD/SSD Docking Station.

2. Sicherheitshinweise

  • Ensure the power adapter is securely connected to a stable power source.
  • Das Gerät darf weder Wasser, Feuchtigkeit noch extremen Temperaturen ausgesetzt werden.
  • Lassen Sie das Gerät nicht fallen und setzen Sie es keinen starken Stößen aus.
  • Versuchen Sie nicht, das Gerät selbst zu zerlegen oder zu reparieren. Wenden Sie sich bei Problemen an den Support.
  • Always handle hard drives carefully to prevent damage.
  • Disconnect the power adapter before inserting or removing drives, especially during offline cloning.

3. Packungsinhalt

Bitte prüfen Sie das Paket auf folgende Artikel:

  • FIDECO USB 3.0 Dual Bay HDD/SSD Docking Station
  • USB 3.0-Datenkabel
  • 12V/3A Netzteil
  • Bedienungsanleitung
Package contents of FIDECO docking station including the station, power adapter, USB cable, and manual.

Image 3.1: Contents of the FIDECO Docking Station package.

4. Produktdiagramm

Diagram of FIDECO docking station showing disk slots, power button, USB 3.0 ports, and DC 12V input.

Abbildung 4.1: Vorder- und Rückseite view of the docking station with labeled components.

  1. Disk Slots: For inserting 2.5-inch or 3.5-inch SATA HDDs/SSDs.
  2. Betriebs-LED: Zeigt den Stromstatus an.
  3. Disk Activity LEDs (25%, 50%, 75%, 100%): Indicate cloning progress or disk activity.
  4. Klon-Schaltfläche: Startet den Offline-Klonvorgang.
  5. USB 3.0 Ports: Zum Anschluss an einen Computer oder andere USB-Geräte.
  6. DC-12-V-Eingang: Zum Anschluss des Netzteils.
  7. Stromschalter: Schaltet das Gerät ein oder aus.

5. Einrichtungsanweisungen

5.1. Connecting to a Computer (Online Mode)

  1. SATA-Festplatte/SSD einlegen: Gently slide your 2.5-inch or 3.5-inch SATA HDD/SSD into the disk slot(s) until it is firmly seated. Ensure the drive is inserted correctly with the SATA connector aligned.
  2. USB-Kabel anschließen: Connect one end of the provided USB 3.0 cable to the docking station's USB 3.0 port and the other end to an available USB 3.0 port on your computer.
  3. Netzteil anschließen: Plug the 12V/3A power adapter into the DC 12V input port on the docking station, then plug the adapter into a power outlet.
  4. Einschalten: Flip the power switch on the back of the docking station to the "ON" position. The power LED will illuminate.
  5. Laufwerkserkennung: Your computer should automatically detect the connected drive(s). For new drives, you may need to initialize and format them through Disk Management (Windows) or Disk Utility (Mac OS) before use.
Four-step setup guide showing inserting HDD, connecting USB, connecting power, and turning on the device.

Image 5.1: Step-by-step connection process for the docking station.

6. Bedienungsanleitung

6.1. Data Transfer (Online Mode)

Once the docking station is connected to your computer and powered on, the inserted drives will appear as external storage devices. You can drag and drop files, kopieren, einfügen oder eine beliebige Standardaktion ausführen file operations as you would with any other external drive.

The USB 3.0 interface supports transfer speeds up to 5Gbps, ensuring fast data access and backup.

Image illustrating high-speed data transfer with an 18TB HDD and 16TB SSD in the docking station connected to a computer.

Image 6.1: High-speed data transfer via USB 3.0.

6.2. Offline Clone Function (Stand-alone Duplication)

The offline clone function allows you to duplicate a source drive to a target drive without needing a computer. This is ideal for system backups or upgrading to a larger drive.

Wichtige Hinweise:

  • The target drive must be equal to or larger in capacity than the source drive.
  • All data on the target drive will be erased during the cloning process. Back up any important data from the target drive before proceeding.
  • Do not connect the docking station to a computer during the offline clone process.

Schritte zum Offline-Klonen:

  1. Sicherstellen, dass die Stromzufuhr unterbrochen ist: Make sure the docking station is powered off and disconnected from any computer.
  2. Laufwerke einlegen:
    • Legen Sie den Quelllaufwerk (das Laufwerk, von dem Sie kopieren möchten) nach Slot 1 (Source HDD).
    • Legen Sie den Ziellaufwerk (das Laufwerk, auf das Sie kopieren möchten) in Slot 2 (Target HDD).
  3. Strom anschließen: Connect the 12V/3A power adapter to the docking station and plug it into a power outlet.
  4. Klonen initiieren: Halten Sie die Schaltfläche „Klonen“. for approximately 3 seconds until the progress LEDs (25%, 50%, 75%, 100%) begin to flash.
  5. Fortschritt überwachen: The progress LEDs will light up sequentially to indicate the cloning status. Each LED represents 25% completion.
  6. Fertigstellung: When all four progress LEDs (25%, 50%, 75%, 100%) remain steadily lit, the cloning process is complete.
  7. Ausschalten und entfernen: Turn off the docking station, disconnect the power adapter, and then safely remove the drives.
Diagram showing the offline clone process: insert drives, connect power, press clone button for 3 seconds, and monitor progress LEDs.

Image 6.2: Offline cloning process illustration.

7. Wartung

  • Halten Sie die Dockingstation sauber und staubfrei. Verwenden Sie zum Reinigen ein weiches, trockenes Tuch.
  • Bewahren Sie das Gerät bei Nichtgebrauch an einem kühlen, trockenen Ort auf.
  • Um eine Überhitzung zu vermeiden, sollten die Lüftungsöffnungen nicht blockiert werden.
  • Always safely eject drives from your computer before powering off the docking station or disconnecting the USB cable to prevent data corruption.

8. Fehlerbehebung

Problem Mögliche Lösung
Das Laufwerk wird vom Computer nicht erkannt.
  • Ensure the drive is properly seated in the slot.
  • Check if the USB cable is securely connected to both the docking station and the computer.
  • Verify the power adapter is connected and the docking station is powered on.
  • Probieren Sie einen anderen USB-Anschluss an Ihrem Computer aus.
  • For new drives, initialize and format them via Disk Management (Windows) or Disk Utility (Mac OS).
Langsame Datenübertragungsgeschwindigkeit.
  • Stellen Sie sicher, dass Sie einen USB-3.0-Anschluss an Ihrem Computer verwenden. USB-2.0-Anschlüsse führen zu geringeren Übertragungsgeschwindigkeiten.
  • Check the condition of the USB 3.0 cable. Try a different cable if available.
  • The speed of the drive itself (HDD vs. SSD) will affect transfer rates.
Offline-Klonen schlägt fehl oder startet nicht.
  • Ensure the docking station is disconnected from the computer.
  • Verify the target drive's capacity is equal to or larger than the source drive's capacity.
  • Make sure both drives are properly inserted.
  • Press and hold the clone button for the required 3 seconds until LEDs flash.
Die Betriebsanzeige-LED leuchtet nicht.
  • Check if the power adapter is securely connected to both the docking station and the power outlet.
  • Stellen Sie sicher, dass sich der Netzschalter in der Position „EIN“ befindet.
  • Versuchen Sie es mit einer anderen Steckdose.

9. Spezifikationen

Besonderheit Detail
Marke FIDECO
Modellnummer Y-482H
Abmessungen (L x B x H) 11.4 x 10.1 x 5.9 cm
Gewicht 301 g
Kompatible Laufwerkstypen 2.5-Zoll-/3.5-Zoll-SATA-I/II/III-HDD/SSD
Maximum Drive Capacity Up to 18 TB per slot
Externe Schnittstelle USB 3.0 (abwärtskompatibel mit USB 2.0)
Übertragungsgeschwindigkeit Bis zu 5 Gbit/s (USB 3.0 SuperSpeed)
Stromversorgung DC 12 V/3 A Netzteil
Betriebssystemkompatibilität Windows XP/Vista/7/8/10, Mac OS 10 and above, Linux
Besondere Merkmale Offline Clone Function, Non-slip base
Image showing compatibility with 2.5-inch and 3.5-inch SATA HDD/SSD, supporting up to 18TB.

Image 9.1: Drive compatibility and maximum capacity.

10. Garantie und Support

The FIDECO USB 3.0 Dual Bay HDD/SSD Docking Station comes with an 18-month warranty from the date of purchase, ensuring peace of mind for your investment. This product has also acquired the PSE mark, indicating compliance with Japanese electrical appliance safety standards.

If you have any questions, concerns, or require technical assistance, please do not hesitate to contact our support team:

We are committed to providing high-quality products and an excellent user experience.