SIAMP Monaco Optima 49 Dual Flush Cistern Valve and Chrome Push Button Instruction Manual

Einführung

This manual provides essential instructions for the installation, operation, and maintenance of your SIAMP Monaco Optima 49 Dual Flush Cistern Valve and Chrome Push Button. Please read this manual thoroughly before installation and retain it for future reference. Proper installation and maintenance will ensure optimal performance and longevity of your product.

Sicherheitshinweise

Warnung: Always turn off the water supply to the cistern before attempting any installation, maintenance, or repair work. Failure to do so may result in water damage or injury.

• Stellen Sie sicher, dass alle Verbindungen wasserdicht sind, um Leckagen zu vermeiden.
• Do not overtighten nuts or fittings, as this can cause damage to the product or cistern.
• Wenn Sie sich bei irgendeinem Teil des Installationsprozesses unsicher sind, konsultieren Sie einen qualifizierten Installateur.
• Kleinteile von Kindern fernhalten.

Produkt überview und Komponenten

Die SIAMP Monaco Optima 49 is a dual flush cistern valve designed for efficient water usage. It features a chrome push button for activating a full or reduced flush.

Abbildung 1: Siamp Monaco Optima 49 Dual Flush Cistern Valve. This diagram illustrates the main components and adjustable dimensions of the flush valve. Key dimensions include adjustable height (B) and adjustable overflow height (C).

• Dual Flush Valve Body: The main mechanism for water release.
• Chrome Push Button: Activates the flush.
• Adjustable Height (B):
  • With collar: 282 to 430mm (lid hole Ø 16 to 38mm and 43 to 50mm)
  • Without collar: 300 to 448mm (lid hole Ø 39 to 42mm)
• Adjustable Overflow Height (C): 155 bis 245 mm.
• Kompatibilität:
  • Lid hole Ø (A): 16 to 50mm
  • Drainage hole Ø (D): 58 to 72mm

Abbildung 2: Chrome Dual Flush Push Button. This button allows selection between a full flush and a reduced flush.

Installationsanleitung

1. Bereiten Sie die Zisterne vor:

   Turn off the water supply to the toilet. Flush the toilet to empty the cistern. Use a sponge to remove any remaining water.

2. Altes Spülventil entfernen (falls zutreffend):

   Unscrew the retaining nut from the underside of the cistern that holds the old flush valve in place. Carefully lift out the old valve.

3. Clean the Cistern Base:

   Clean the area around the drainage hole in the cistern to ensure a good seal for the new valve.
4. Install the New Flush Valve:

   Place the new SIAMP Monaco Optima 49 flush valve into the drainage hole from inside the cistern, ensuring the rubber seal is correctly seated. From the underside of the cistern, thread the retaining nut onto the valve and hand-tighten. Nicht zu fest anziehen.

5. Adjust Valve Height and Overflow:

   Siehe Abbildung 1 for adjustable height (B) and overflow height (C). Adjust the valve to fit your cistern's height and desired overflow level. Ensure the overflow pipe is below the cistern's overflow level but above the water line.

6. Install the Push Button:

   Insert the chrome push button assembly through the lid hole of your cistern. Connect the button's activation rods to the flush valve mechanism. Ensure the rods are correctly aligned and allow for smooth operation of both full and reduced flush functions.
7. Wasserversorgung wiederherstellen:

   Turn the water supply back on. Allow the cistern to fill and check for any leaks around the flush valve and connections. If leaks occur, gently tighten the retaining nut or check the seal's position.

8. Spültest:

   Perform several test flushes (full and reduced) to ensure proper operation and water levels.

Bedienungsanleitung

Die SIAMP Monaco Optima 49 features a dual flush mechanism, allowing you to choose between a full flush for solid waste and a reduced flush for liquid waste, conserving water.

• Reduzierte Spülung: Press the smaller button or the smaller section of the chrome push button. This releases a smaller volume of water, ideal for liquid waste.
• Vollspülung: Press the larger button or the larger section of the chrome push button. This releases the full volume of water from the cistern, suitable for solid waste.

Ensure the button returns to its original position after each flush to allow the cistern to refill properly.

Wartung

• Cleaning the Push Button: Clean the chrome push button with a soft, damp cloth and mild soap. Avoid abrasive cleaners or harsh chemicals, as these can damage the chrome finish.
• Innenreinigung: Periodically, you may need to clean the internal components of the flush valve if you notice reduced flush performance or blockages. Turn off the water supply, empty the cistern, and carefully remove the valve for cleaning. Rinse components with clean water.
• Dichtungsinspektion: Inspect the rubber seals periodically for wear or damage. Worn seals can lead to leaks. Replace seals as necessary.

Fehlerbehebung

Technische Daten

Garantie und Support

For warranty information or technical support, please refer to the official SIAMP webBesuchen Sie unsere Website oder kontaktieren Sie Ihren Händler. Bewahren Sie Ihren Kaufbeleg für Garantieansprüche auf.

Hersteller: SIAMP

Teilenummer: 32499910