Flysky FS-GR3E 3-Channel 2.4GHz Receiver User Manual

Einführung

The Flysky FS-GR3E is a reliable 3-channel 2.4GHz receiver designed for use with RC cars and boats. It utilizes Flysky's Automatic Frequency Hopping Digital System (AFHDS) technology to provide a stable and interference-free connection. This receiver is compatible with various Flysky transmitters, including the FS-GT2, FS-GT2B, FS-GT3B, and FS-GT3C. This manual provides essential information for the proper setup, operation, and maintenance of your FS-GR3E receiver.

Bild: The Flysky FS-GR3E 3-Channel 2.4GHz Receiver. This image displays the compact black receiver unit with its antenna wire and various ports for connection to servos, ESC, and power.

Sicherheitshinweise

Please read and understand the following safety guidelines before operating your receiver:

• Ensure correct polarity when connecting power to the receiver. Incorrect connections can cause damage.
• Betreiben Sie Ihr RC-Modell in offenen Bereichen, fernab von Personen, Fahrzeugen und Hindernissen.
• Avoid exposing the receiver to moisture, extreme temperatures, or direct sunlight for extended periods.
• Always turn on your transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.
• Überprüfen Sie regelmäßig alle Kabel und Anschlüsse auf Beschädigungen oder lose Kontakte.

Packungsinhalt

Überprüfen Sie, ob alle Artikel im Paket vorhanden sind:

• 1 x Flysky FS-GR3E 2.4GHz 3-Channel Receiver

Technische Daten

Aufstellen

1. Installation

Mount the FS-GR3E receiver securely in your RC model, ensuring it is protected from vibrations and moisture. Position the antenna wire as straight as possible and away from metal parts or carbon fiber chassis to maximize range and signal quality. Connect your Electronic Speed Controller (ESC) to Channel 2 (throttle), and your steering servo to Channel 1. If using a third channel for auxiliary functions, connect it to Channel 3.

2. Empfänger mit Sender verbinden

The receiver must be bound to your Flysky transmitter before use. Follow these steps:

1. Stellen Sie sicher, dass Ihr Sender ausgeschaltet ist.
2. Insert the bind plug (usually included with your transmitter or receiver) into the "BIND" port (Channel 3) on the FS-GR3E receiver.
3. Connect power to the receiver (e.g., via the ESC or a separate battery pack connected to the VCC port). The receiver's LED should start flashing rapidly, indicating it is in binding mode.
4. While holding the bind button on your transmitter (or following its specific binding procedure), power on the transmitter.
5. Die LED am Empfänger sollte aufhören zu blinken und dauerhaft leuchten, was eine erfolgreiche Bindung anzeigt.
6. Turn off the receiver, then turn off the transmitter.
7. Entfernen Sie den Bindestecker vom Empfänger.
8. Power on the transmitter first, then the receiver. Verify that the receiver's LED is solid and that the controls respond correctly.

Note: If binding fails, repeat the steps. Some transmitters may have slightly different binding procedures; refer to your transmitter's manual for specific instructions.

Betrieb

1. Failsafe Function

The FS-GR3E receiver features a failsafe function on Channel 2 (throttle) to prevent runaway models in case of signal loss. To set the failsafe position:

1. Ensure the receiver is bound to the transmitter and both are powered on.
2. Position the throttle stick on your transmitter to the desired failsafe position (e.g., neutral or brake).
3. Locate the small failsafe button on the receiver. Press and hold this button until the receiver's LED blinks once, then release.
4. The failsafe position is now set. To test, power on the transmitter and receiver, then turn off the transmitter. The throttle should move to the set failsafe position.

It is recommended to set the failsafe to a neutral or brake position for safety.

2. Channel Assignment

The FS-GR3E receiver has 3 channels. Standard assignments are:

• Kanal 1: Steering (for RC cars/boats)
• Kanal 2: Throttle (for RC cars/boats)
• Kanal 3: Auxiliary function (e.g., lights, gear shift, or used as Bind port)

Wartung

To ensure the longevity and optimal performance of your FS-GR3E receiver, follow these maintenance tips:

• Halten Sie den Empfänger sauber und frei von Staub, Schmutz und Ablagerungen. Verwenden Sie zum Reinigen eine weiche, trockene Bürste oder Druckluft.
• Avoid exposing the receiver to water or excessive humidity. If it gets wet, disconnect power immediately and allow it to dry completely before re-use.
• Store the receiver in a cool, dry place when not in use.
• Regularly check the antenna wire for any cuts, kinks, or damage. A damaged antenna can significantly reduce range.
• Stellen Sie sicher, dass alle Verbindungen zum Empfänger fest sitzen und frei von Korrosion sind.

Fehlerbehebung

Garantie und Support

Informationen zur Garantie und zum technischen Support finden Sie auf der offiziellen Flysky-Website. webBesuchen Sie unsere Website oder wenden Sie sich an Ihren autorisierten Flysky-Händler. Bewahren Sie Ihren Kaufbeleg als Kaufnachweis auf.