1. Einleitung
The Mitutoyo VDS-15DCX is a high-precision digital depth gauge designed for accurate measurement of depths, steps, and grooves. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your instrument. Please read this manual thoroughly before operating the device.
Image: Mitutoyo VDS-15DCX Digital Depth Gauge. This image displays the main unit of the digital depth gauge, showing its digital display, measuring base, and measuring rod.
2. Einrichtung
2.1 Auspacken und Prüfen
- Carefully remove the depth gauge from its packaging.
- Inspect the instrument for any signs of damage that may have occurred during transit. If damage is found, do not use the device and contact your supplier.
- Prüfen Sie, ob alle in der Packliste aufgeführten Komponenten vorhanden sind.
2.2 Einlegen der Batterie
The VDS-15DCX uses one SR44 silver oxide button cell battery.
- Locate the battery cover on the back of the digital display unit.
- Using a small screwdriver or coin, gently turn the battery cover counter-clockwise to open.
- Insert a new SR44 battery with the positive (+) side facing upwards.
- Bringen Sie die Batterieabdeckung wieder an und drehen Sie sie im Uhrzeigersinn, um sie zu befestigen.
- Press the ON/OFF button to confirm the display powers on.
2.3 Reinigung von Messflächen
Before use, gently wipe the measuring base and the tip of the measuring rod with a clean, lint-free cloth. Ensure no dust, oil, or debris is present on these surfaces, as this can affect measurement accuracy.
2.4 Zero-Setting Procedure
To ensure accurate measurements, the depth gauge must be zero-set before use.
- Place the depth gauge on a flat, stable, and clean reference surface.
- Ensure the measuring base is flush with the reference surface and the measuring rod is fully retracted.
- Drücken Sie die NULL button. The display should show '0.00' or '0.000'.
- The instrument is now ready for measurement.
3. Bedienungsanleitung
3.1 Grundlegende Messung
- Ensure the depth gauge is properly zero-set (refer to Section 2.4).
- Place the measuring base firmly on the top surface of the workpiece or feature to be measured.
- Slowly extend the measuring rod until its tip makes contact with the bottom surface of the depth or step. Ensure the rod is perpendicular to the bottom surface.
- Lesen Sie den auf dem LCD-Bildschirm angezeigten Messwert ab.
3.2 Unit Conversion (mm/inch)
To switch between metric (mm) and imperial (inch) units, press the mm / Zoll button. The display will show the current unit of measurement.
3.3 Absolute (ABS) and Incremental (INC) Measurement
The VDS-15DCX allows for both absolute and incremental measurements.
- Absolute (ABS) Mode: This mode measures from the true zero point, which is set when the gauge is zeroed on a reference surface.
- Incremental (INC) Mode: To measure a difference from an arbitrary point, position the measuring rod at the desired reference point on the workpiece and press the NULL button. The display will reset to zero, and subsequent movements will show the incremental distance from this new zero point. Press the ABS/INKL button to toggle between modes.
3.4 Datenhaltefunktion
If your model includes a HALTEN button, pressing it will freeze the current reading on the display, allowing you to remove the gauge from the workpiece and record the measurement. Press the button again to release the hold function.
4. Wartung
4.1 Reinigung
- After each use, wipe the entire instrument, especially the measuring surfaces, with a clean, dry, lint-free cloth.
- For stubborn dirt or oil, use a cloth lightly dampened with isopropyl alcohol. Avoid using strong solvents or abrasive cleaners.
- Do not immerse the depth gauge in any liquid.
4.2 Speicherung
- Store the depth gauge in its original protective case when not in use.
- Store in a dry environment, away from direct sunlight, extreme temperatures, and high humidity.
- Avoid storing in areas with excessive dust or corrosive fumes.
4.3 Batteriewechsel
Replace the battery when the display becomes dim or an indicator (e.g., 'B' or battery icon) appears on the screen. Refer to Section 2.2 for battery installation instructions. Dispose of used batteries according to local regulations.
4.4 Calibration Checks
Periodically check the accuracy of the depth gauge using a known reference standard (e.g., gauge blocks). If the readings are consistently outside the specified accuracy, the instrument may require professional calibration or repair.
5. Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Das Display lässt sich nicht einschalten | Leere oder falsch eingesetzte Batterie | Replace battery (Section 2.2) or ensure correct polarity. |
| Ungenaue Messwerte |
|
|
| Das Display zeigt „E“ oder einen Fehlercode an. | Internal error or sensor issue | Remove and reinsert battery. If error persists, contact customer support. |
| Tasten reagieren nicht | Niedriger Batteriestand oder interne Fehlfunktion | Replace battery. If issue continues, contact customer support. |
6. Spezifikationen
| Besonderheit | Spezifikation |
|---|---|
| Modellnummer | VDS-15DCX (571-201-20) |
| Messbereich | 0-150 mm (0-6 Zoll) |
| Auflösung | 0.01 mm (0.0005 Zoll) |
| Genauigkeit | ±0.02 mm (±0.001 Zoll) |
| Anzeige | LCD |
| Stromversorgung | SR44 (1 pc) |
| Gewicht | 207 g (0.45 Pfund) |
| Hersteller | Mitutoyo |
7. Garantieinformationen
Mitutoyo products are manufactured to high standards and are typically covered by a limited warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region and product. Please refer to the warranty card included with your product or contact your local Mitutoyo distributor for detailed warranty information.
8. Kundendienst
For technical assistance, service, or inquiries regarding your Mitutoyo VDS-15DCX digital depth gauge, please contact your authorized Mitutoyo distributor or visit the official Mitutoyo website for regional contact information. When contacting support, please have your model number (VDS-15DCX) and serial number (if applicable) ready.