1. Einleitung
Thank you for choosing the Kapego Ultra 70 Dimmable LED Power Supply. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your device. Please read this manual thoroughly before installation and keep it for future reference.
1.1 Sicherheitshinweise
- Elektrische Gefahr: Installation und Wartung müssen von einem qualifizierten Elektriker gemäß den örtlichen Elektrovorschriften und -bestimmungen durchgeführt werden.
- Disconnect power before installation, maintenance, or troubleshooting.
- Bei Beschädigungen darf das Gerät nicht in Betrieb genommen werden.
- Sorgen Sie für ausreichende Belüftung, um eine Überhitzung zu vermeiden.
- This device is rated IP20, meaning it is protected against solid objects larger than 12.5mm but has no protection against water. Do not expose to moisture or water.
2. Produktüberschreitungview
The Kapego Ultra 70 is a constant voltage electronic transformer designed for dimmable LED lighting applications. It features phase-cut dimming control, allowing for smooth adjustment of light intensity when paired with compatible dimmers.
2.1 Hauptmerkmale
- Material: Durable plastic housing.
- Farbe: Schwarzes Finish.
- Leistungsabgabe: 0-70.00W, suitable for various LED loads.
- Kontrolle: Phase-cut dimming for compatibility with leading and trailing edge dimmers.
- Eingangslautstärketage: 220-240V AC, 50-60Hz.
- Ausgangsvolumentage: 12V Wechselstrom.
2.2 Produktbild
3. Einrichtung und Installation
Wichtig: All installation work must be carried out by a qualified electrician. Ensure power is disconnected at the main circuit breaker before proceeding.
- Stromabschaltung: Turn off the main power supply to the circuit where the power supply will be installed. Verify that the power is off using a voltage Tester.
- Montage: Choose a suitable, dry location for mounting the power supply, ensuring adequate ventilation. The device is not waterproof (IP20). Secure the power supply using appropriate fasteners.
- Input Wiring (PRI): Connect the main AC power supply (220-240V AC, 50-60Hz) to the input terminals marked 'PRI' (L and N). Use appropriate wire gauges (0.75-2.50 mm² recommended).
- Schließen Sie den stromführenden Draht (L) an den Anschluss 'L' an.
- Schließen Sie den Neutralleiter (N) an den Anschluss 'N' an.
- Output Wiring (SEC): Connect your 12V AC LED lighting fixtures to the output terminals marked 'SEC'. Ensure the total wattage of the connected LED fixtures does not exceed 70W. Use appropriate wire gauges (0.75-2.50 mm² recommended).
- Dimmeranschluss (optional): If using a dimmer, connect it on the primary (input) side of the power supply, following the dimmer manufacturer's instructions. This power supply is designed for phase-cut dimmers.
- Endkontrolle: Double-check all connections for proper polarity and secure fastening. Ensure no bare wires are exposed.
- Wiederherstellung der Stromversorgung: Stellen Sie die Stromversorgung des Stromkreises wieder her.
4. Bedienungsanleitung
Once properly installed, the Kapego Ultra 70 Dimmable LED Power Supply operates automatically when power is supplied. If a compatible phase-cut dimmer is connected to the input, you can adjust the brightness of the connected LED lights using the dimmer control.
- Ein-/Ausschalten: Use the main light switch or dimmer switch to turn the connected LED lights on or off.
- Dimmen: Rotate or adjust the dimmer control to increase or decrease the light output. Ensure the dimmer is compatible with phase-cut electronic transformers.
5. Wartung
The Kapego Ultra 70 Dimmable LED Power Supply requires minimal maintenance. Follow these guidelines to ensure longevity and optimal performance:
- Reinigung: Ensure power is disconnected before cleaning. Wipe the exterior of the power supply with a soft, dry cloth. Do not use abrasive cleaners, solvents, or liquids.
- Inspektion: Periodically inspect the wiring and connections for any signs of damage, loose connections, or overheating. Address any issues promptly.
- Belüftung: Ensure that the power supply's ventilation openings are not obstructed.
6. Fehlerbehebung
If you experience issues with your Kapego Ultra 70 Dimmable LED Power Supply, refer to the following common problems and solutions:
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Keine Lichtleistung |
|
|
| Flackerndes oder instabiles Licht |
|
|
| Dimmen funktioniert nicht |
|
|
Sollte das Problem nach dem Ausprobieren dieser Lösungsansätze weiterhin bestehen, wenden Sie sich bitte an einen qualifizierten Elektriker oder an den Kundendienst.
7. Spezifikationen
| Parameter | Wert |
|---|---|
| Modellnummer | 180515 |
| Marke | Deko-Light (Kapego) |
| Eingangslautstärketage | 220-240 V AC, 50-60 Hz |
| Eingangsstrom | 0.29A (PRI) |
| Ausgangsvolumentage | 12V AC (SEC: 11.5V~eff) |
| Ausgangsstrom | 0-6.0A |
| Ausgangsleistung | 0-70.00 W |
| Dimmsteuerung | Phase Cut (Leading/Trailing Edge) |
| Leistungsfaktor (λ) | ≥0.99 |
| Material | Plastik |
| Farbe | Schwarz |
| IP-Schutzart | IP20 (Kein Wasserschutz) |
| Operating Temperature (ta) | 50°C |
| Case Temperature (tc) | 80°C |
| Produktabmessungen (L x B x H) | 115 mm x 45 mm x 28 mm (4.53 x 1.77 x 1.10 Zoll) |
| Gewicht | 120 Gramm |
| Leiterquerschnitt | 0.75-2.50 mm² |
8. Garantie und Support
This Kapego product is covered by a standard manufacturer's warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims.
8.1 Kundendienst
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your retailer or the manufacturer directly. Refer to the packaging or the manufacturer's webWebsite für Kontaktdaten.
Hersteller: Kapego (Deko-Light)
Modell: 180515