DATA FROG GG04 Wireless Controller For Switch Oled User Manual

DATA FROG GG04 Wireless Controller For Switch Oled

Features

Button for Switch

Button for PC / Android / iOS

Switch Connection

Switch Wireless Connection

1. Turn on Switch to click [Controllers]
2. Click [Change Grip/Order]
3. Press [Sync] on the back for 3s , then led
4. lights flash fast. Finally the connection is done when the lights keep on.

Switch Wired Connection

1. Make sure the [Pro Controller Wired Communication) is on in the Switch settings. (Settings>Controllers and Sensors>Pro Controller Wired Communications On)
2. Wired connect as the picture

Wake up Switch

1. After the first connection, just need to press the [HOME] to wake up and reconnect. ( You can reconnect not only on the [Change Grip/Order] page, but on the main page )

PC Connection

PC Wired Connection

1. PC Wired Connection (Please use the USB to C cable in the box to wired connect with PC)

Steam System Connection
Hold R3 button and connect to PC via cable, the controller will turn to Switch USB mode The function of 3.5mm jack, motion sensor is available for steam system.

Phone Connection

• Press the [Sync]+ “Y” button for 3s (This mode support Asphalt/Minecraft/ Cross Fire etc. games)
• Press the [Sync]+ “X” button for 3s (This mode support Asphalt/Minecraft/ CrossFire etc. games)

Macro Function

1. Enter into set Press and hold the Turbo button + ML(MR) button for 2s until the No.2 and NO.3 lights keep on, then loosen the ML(MR) button.
2. Set button Press the button which you want to set one by one. Support to record the interval between the buttons)
3. Complete setup Tap the ML(MR) button after setting.
4. Clean Setup Follow the Step 1 and then steps 3 to clear the Marco setting

FOR EXAMPLE

• Press and hold the Turbo+ ML button until the green LED lights keep on (the interval time is Is) + “A” (the interval time is Click
• ML finally and then setup completed
• After setting, the function of pressing ML button is “B” (after (after 3s)+”X”
• Macro setting will be saved even after reconnecting.

CLEAN ALL MACRO SETTING

• Hold Turbo and – button for 5s to clean all Macro settings.
• Gamepad should vibrate one time for showing

Turbo

• Manual Fire
  Press any one button and [ Turbo ] to set this specified button as Manual Fire button, it means when you press and hold this specified button, this button can repeat to work all the time after setting Manual Fire.
• Auto Fire
  Repeat to press the specified button and [Turbo] , the Manual Fire turns into Auto Fire, it means this specified button can repeat to work automatically all the time but you don’t need to press that button.
• Clean Fire
  Repeat to press the specified button and [Turbo] for the third time, it can clean all set for this specified button .lf you want to clean all button’s setting, you can long press the [Turbo] for 5s, then the lights keep on and the clean operation is done.

Turbo Rate Setting

P.s.: There will be vibration feedback after each Turbo Rate Setting.

Light Mode

Other Functions

Vibration Function

Notice:
Vibration strength adjustment available for Nintendo Switch ONLY

Charging Instructions

• Non-Connection Condition (the indicator lights will keep flash slowly and turn off by itself after fully charged)
• Connection Condition (the indicator lights will keep flash slowly and keep on after fully charged)
• Low-power Alert (the indicator lights flash quickly)

Low-Voltage Alert

• If the battery voltage is lower than 3.5V±0.1V, the indicator lights flash quickly to prompt low voltage
• If the battery voltage is lower than 3.3V±0.1V, controller will sleep automatically

Sleeping Automatically

• When the controller is connected, tap on the [ Connection ] button, the controller will be disconnected and enter the sleeping mode.
• Without any operation within 5 minutes, the controller will sleep automatically
• The controller will sleep together with the console if the console sleeps

Reset Controller
Press and hold the HOME button for IOS