DAEWOO logo

DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum

DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 image

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed. These instructions should be saved for future reference:

  • Read and familiarise yourself with all operating instructions before using this Vacuum Cleaner.
  • Before plugging your unit into the mains, visually check that the unit is intact and has not suffered any transit damage.
  • Check that the voltage indicated on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.
  • This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
  • Keep the appliance and its cord out of reach of children less than 8 years when it is energised or cooling down.
  • Do not immerse the appliance or its cord in water or any other liquids.
  • Do not leave the appliance unattended during use.
  • Do not leave the appliance unattended whilst connected to the mains supply.
  • Do not use this appliance outdoors.
  • It is imperative to unplug the power cord after the appliance has been used, before it is cleaned and whilst being repaired.
  • Repairs to electrical appliances should only be performed by a qualified electrician. Improper repairs may place user at serious risk.
  • Do not operate this appliance with a damaged plug or cord, after a malfunction or after being dropped or damaged in any way.
  • Regular, periodic checks should be carried out on the mains cable to
  • ensure no damage is evident. Should there be any signs of damage the appliance should not be used.
  • If the power cable is damaged, it should only be replaced by the manufacturer or a suitable qualified after-sales-service in order to avoid a hazard
  • Do not allow the main cable to hang over sharp edges or come in contact with hot surfaces.
  • Allow the unit to cool before storage.
  • Before cleaning, disconnect the appliance from the mains supply and allow to cool.
  • This appliance is intended for household use only and should not be used for industrial purposes.
  • Do not use any accessories or attachments with this appliance other than those supplied or recommended by supplier.
  • Do not use this appliance for anything other than its intended use.
  • Do not push objects into any openings as damage to the appliance and/or electric shock may occur.
  • Unplug after each use. Grasp the plug, not the cord.
  • Do not pull or carry the Vacuum Cleaner by the electrical cord, use the handle provided.
  • Ensure fingers and other objects are never placed in any part of the vacuum cleaner. Clothing or hair may become trapped if the vacuum is used improperly.
  • Keep hair, loose clothing, jewellery, fingers and all parts of the body away from openings and moving parts.
  • Keep all air vents clear and free of dust, lint, hair and anything else that may reduce airflow.
  • Avoid directing the appliance towards naked flames as the air discharged may extinguish gas fires or pilot lights and may disturb ashes in open fires.
  • Do not Vacuum water or any other liquids with this vacuum.
  • Do not Vacuum hot ashes or lit cigarettes, etc.
  • Never use the appliance without the filter in place.
  • Do not use the Vacuum without the Dust Compartment attached.
  • Do not vacuum any large or broken objects such as glass.
  • Do not vacuum anything that is burning or smoking such as cigarettes, matches or hot ashes.

Waste batteries should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

Description of Parts

DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig1

  1. Dust Release Catch
  2. Hepa & Cyclonic Filters
  3. Dust Compartment
  4. Dust Compartment Catch
  5. Air Outlet
  6. Motor Housing
  7. Display Panel
  8. On/Off Trigger Switch
  9. Handle
  10. Battery Compartment
  11. Charging Socket
  12. Battery Compartment Catch
  13. Air Intake
  14. Attachment Release Catch
  15. Dust Compartment Cover
    Description of Parts – AccessoriesDAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig2DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig3
  16. Motorise Floor Tool
  17. Crevice & Upholstery Tool
  18. Small Power Plug
  19. Mains Charger
  20. Wall Mount Bracket
  21. Alumarp ietn iBurmu sFlh exi-Tube
  22. Carpet Brush
  23. Hard Floor Roller
  24. Long Reach Crevice Tool
  25. Information Screen
  26. Battery Charge Display
  27. Dust Sensor Failure
  28. High Speed
  29. Intelligent AUTO Mode
  30. Battery Indicator
  31. Brush Blockage Indicator
  32. Air Intake Blockage Indicator
  33. Eco Speed
  34. Speed/Suction Indicator

Before the first time you use your Cordless Vacuum Cleaner
Please read these operating instructions thoroughly and keep them in a safe place for future reference.
Remove all packing materials and discard responsibly.

Charging the internal Battery

Before use, please ensure that the internal rechargeable battery is fully charged as follows:

  1. Insert the Small Power Plug (18) of the Mains Charger (19) into the Charging Socket (11).
  2. Plug the Mains Charger (19) into the nearest mains socket.
  3. The Battery Indicator (30) will flash green and the Battery Charge Display (26) will count up to 100% as the internal battery charges.
  4. Once the battery is fully charged (after approximately 5 hours), the Battery Charge Display (26) will display 100 (arrowed below) showing that the internal battery is 100% fully charged and the Mains Charger (19) can now be removed.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig4NB The internal battery will need recharging when the Battery Indicator (30) flashes red and the Battery Charge Display (26) reads a low value (less than 10%). Follow the above procedure (1 – 4) to recharge the internal battery.

Attaching the Accessories
CAUTION Ensure that the vacuum cleaner is not connected to the mains charger before use.
The Floor Attachment

  1. Push the Aluminium Flexi Tube (21) onto the Air Intake (13) until it clicks home as shown below:DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig5
  2. Push the Motorised Floor Tool (16) onto the other end of the Aluminium Flexi Tube (21) again until it clicks home.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig6

Using Your Cordless Vacuum Cleaner

The Motorised Floor Tool (16)

  1. Before using the Motorised Floor Tool (16),first, choose the appropriate brush type for the floor type being cleaned:
    Select the Carpet Brush (22) for vacuum cleaning carpets, rugs, etc.
    Select the Hard Floor Roller (23) for cleaning vinyl, laminate, tiled floors, etc.DAEWOOs Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig7
  2. To change the brush attachment, slide the catch (a) to the left and lift up the brush bearing retaining clip (b) on the underside of the Motorised Floor Tool (16) as shown left.
    NB the Carpet Brush (22) is currently fitted in this example.
    Lift out the Carpet Brush (22) and the brush bearing (c). Remove the brush bearing from the Carpet Brush (22).DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig8
  3. Place the brush bearing (c.) onto the end of the Hard Floor Roller (23) as shown above left. Once in place, insert the Hard Floor Roller (23) into the Motorised Floor Tool (16) as shown above right.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig9
  4. Finally, hook the brush bearing retaining clip at the front edge (d) and push down into until it clicks into place (e) as shown left.
    The vacuum is now ready to clean hard floors.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig10

Using Your Cyclone Digi-Flex Vacuum

  1. Right: Grasp the vacuum cleaner firmly by the Handle (9) and press the On/off Trigger Switch (8) to power up the cleaner.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig11
  2. Left: During use, on the Information Screen (25), press the Eco Speed (33) to lower the vacuum speed/suction or High Speed (28) to increase speed/suction. The Speed/Suction Indicator (34) will move to show the current speed/suction level (low to high).DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig12
  3. Right: Place your foot gently on the Motorised Floor Tool (16) and pull the cleaner back by the Handle (9) and start vacuum cleaning.
    Press the On/off Trigger Switch (8) again at the end of cleaning to switch the cleaner off.
    Far Right: Press the catch on the Flexi joint
    (arrowed right) to release the Aluminium Flexi Tube (21) so that the tube can bend in order to clean under furniture and other close to the ground objects.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig13
  4. Left: If the Aluminium Flexi Tube (21) is not required, the Motorised Floor Tool (16) can be attached directly to the vacuum as shown left for cleaning hard to get at areas such as stairs, car seats, etc.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig14

Using the Crevice & Upholstery Tool (17)

  1. Attach the Crevice Tool & Upholstery Tool (17) onto the Aluminium Flexi Tube (21) to clean carpet edges and hard to get at areas:DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig15DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig16Left: Slide the brush back on the tool to reveal the crevice tool to clean carpet edges, etc. Alternatively use the Long Reach Crevice Tool (24).
    Right: Pull the brush down on the tool to clean curtains, upholstery, etc.
  2. If the Aluminium Flexi Tube (21) is not required, attach the Crevice Tool & Upholstery Tool (17) directly to the cleaner, this useful for cleaning soft furnishings, car seats, stairs, etc.:DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig17Above: Using the Crevice Tool & Upholstery Tool (17) on Upholstery. DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig18Above: Using the Crevice Tool & Upholstery Tool (17) to clean the car.

Emptying and Cleaning Your Cyclone Digi-Flex Vacuum Cleaner

WARNING Always disconnect the cleaner from the mains charger before cleaning.

  1. Once the dust level reaches the ‘MAX’ mark (arrowed left) on the Dust Compartment (3) it will need emptying and the filters cleaned.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig19WARNING do not continue to use your vacuum cleaner once the ‘MAX’ mark has been reached as permanent damage may occur to the appliance.
  2. To empty the cleaner, hold the Dust Compartment (3) over a dust bin as shown right and press the Dust Release Catch (1) (arrowed right) and the Dust Compartment Cover (15) of the dust compartment will swing open and allow the collected dust to fall out into the dust bin.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig20
  3. Hold the Dust Compartment (3) and press the Dust Compartment Catch (4) arrowed left and lift up the dust compartment and remove.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig21
  4. Rem ove the Hepa & Cyclonic Filters (2) from the Dust Compartment (3) as sh own right:DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig22
  5. Above: Wash the Hepa & Cyclonic Filters (2) in warm running water until clean. Allow the filters to dry thoroughly for 24 hours before reuse.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig23
  6. Left: First replace the Hepa Filter inside the Cyclonic Filter, rotate the Hepa filter clockwise to lock it onto the Cyclonic Filter as shown.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig24
  7. Right: Replace the Hepa & Cyclonic Filters (2) into the Dust Compartment (3) as shown.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig25
  8. Left: Replace the Dust Compartment (3) onto the vacuum by hooking the dust compartment on and pushing it down until it clicks home as shown.DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig26

Care and Use of your Cordless Vacuum Cleaner

  • Always disconnect the cleaner from the mains charger before cleaning.
  • Clean outside of the cleaner with a clean damp cloth. Never clean with harsh or abrasive cleaners.
  • Do not submerge the cleaner or its charger in water or any other liquids.
  • Empty the Dust Compartment (3) as soon as the ‘MAX’ mark has been reached.*
  • Wash the Hepa & Cyclonic Filters (2) regularly – see table below.
  • Allow the filters to thoroughly dry out for 24 hours before reassembly and use.

WARNING do not continue to use your vacuum cleaner once the ‘MAX’ mark has been reached as permanent damage may occur to the appliance.

Recommended filter cleaning intervals

Filter Type Recommended cleaning period
Hepa FilterDAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig27 · Shake out debris when you empty the dust container

· Rinse under warm water once a month

· Allow to dry thoroughly for 24 hours before reuse.

 

Cyclonic FilterDAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig28

· Shake out debris once a month

· Rinse under warm water once a month.

·  Allow to dry thoroughly for 24 hours before reuse.

WARNING Ensure the filters are cleaned periodically according to the table above, failure to clean the filters regularly will severely impair the performance and permanent damage may occur to the appliance and may invalidate your warranty.

Technical Specification

Model Number FLR00041
Mains Charger Input: AC 100-240V ~ 50/60Hz Output: 36V DC 500mA
Rated Power 250W
Battery 29.6V 2500mAh Li-Ion (8 cells)
Unpacked Weight (approx.) 2.2 Kgs
Dimensions (approx.) 328mm (l) x 110mm (w) x 220mm (h)
Vacuum (max) ≥24kpa
Noise Level (approx.) 72dB
Dust Compartment Capacity 0.8L

DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig29

Troubleshooting Guide

Problem Possible Cause Solution
Unit fails to turn on. Internal battery not charged.

The charger is not plugged into the mains socket.

Charge the internal battery.

 

Ensure the charger is fully inserted into the socket and the socket is switched on.

Low suction or poor pick-up. Dust Compartment is full. Filters are clogged.

Low Power Selected

Empty the cylinder.

Check and clean the filters.

Press the Min/Max Power Button (8)

The vacuum is making a

“hissing” sound.

The airflow is restricted Empty the Dust Compartment. Check and clean the filters.

Clear any blockages if

necessary.

 

Brush Blockage Indicator

(31) not lit

The Carpet Brush (22) or Hard Floor Roller (23) is obstructed and/or tangled with hair and debris Switch off the vacuum cleaner and remove obstruction from the Carpet Brush (22) or Hard Floor Roller (23).
 

Air Intake Blockage Indicator

(32) not lit

The Aluminium Flexi-Tube

(21) and/or vacuum Air Inlet (5) are blocked.

Switch off the vacuum cleaner and remove obstruction from the Aluminium Flexi-Tube (21) and/or vacuum Air Inlet (5)
 

Dust Sensor Failure (27) Indicator not lit

The vacuum is very dirty and/or blocked and the Dust Compartment full. Switch off the vacuum cleaner and empty and clean the Dust Compartment (3), Filters (2),

Aluminium Flexi-Tube (21) and/or vacuum Air Inlet (5)

Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 fig30

Documents / Resources

DAEWOO Cyclone Digi-Flex 29.6 Cordless Vacuum FLR00041 [pdf] User Manual
DAEWOO, Cyclone, Digi Flex, Cordless, Vacuum, FLR00041

Leave a comment

Your email address will not be published.