TOGUARD CE18A Dash Camera Brugervejledning
Vigtig besked
- This product is intended for using in motor vehicles only. Do NOT install the camera where it might block the driver’s view of road (including the mirrors) or the deployment of the airbag.
- Before using this device, please insert the memory card first, and need to format micro SD card to FAT32 format on PC firstly, then format the memory card in camera menu.
- This camera records video at high resolution. Be sure to use high speed Micro SD card (Class 10 or above). 16 GB or 32 GB Micro SD card is recommended.
- safety reasons, this camera has a small built-in battery, which is used to save the video file after external power supply cuts off (car turns off).
- Sørg for, at kameralinsen er ren, og at der ikke er noget, der blokerer linsen.
- Efterlad IKKE kameraet i direkte sollys i en længere periode, eller hvor temperaturen kan gå over 140 ° C.
- Power
- When the camera is off, press and hold power button to turn on the camera.
- Under any mode, press and hold power button to turn off the camera.
- When the camera is on, short press to turn on/off screen display.
- menu
- In Video / Photo / Playback mode, short press to enter setup menu for that particular mode, short press again to access System Setup Menu.
- During video recording, short press to manually lock/ unlock current video.
- In Standby, press and hold to switch working mode.
- Up
- During video recording, short press to turn ON/OFF audio recording.
- In setup menu, short press to select options and adjust values.
- In Playback, short press to select files.
- ned
- In setup menu, short press to select options and adjust values.
- In Playback, short press to select files.
- In the recording state, short press the down button to switch the recording screen.
- OK
- In Video Mode. short press to start/stop recording.
- In Photo Mode. short press to take a photo.
- In Setup Menu, short press to confirm selection and changes.
- In Playback Mode. short press to play a video file.
- Nulstil
- Short press to reset the camera to factory default status.
Opsætning og installation
- Before installation, please check the camera’s normal function, and make sure you are using a high speed Micro SD card (speed Class 10 or above),and format the card in the camera menu before recording.
- Use the suction cup mount to install the CE18A dash cam on the windshield. The recommended place is near the rearview mirror facing front, adjust the lens angle for best coverage
- .Adjust the lens angle of the camera, make sure you get the best coverage over the hood and the road ahead, so you can record what happens.
- Connect the power to the camera and the cigarette lighter, hide the rest of the cable in the gap of the interior trim board.
Driftsart
The CE18A operates in 3 modes: Video Recording Mode, Photo Mode and Playback Mode. These modes also have menu to help you configure recording and taking photos. Press and hold “Menu” to switch between different modes and access to the mode you want. Watch the icon on top left corner of the screen for each mode.
Videooptagelsestilstand
The camera will automatically enter Video Recording Mode and start recording when connected to a car charger and power on. A Red dot flashing on the top left corner indicates recording is in progress. Press the OK to stop recording, or start recording again.
In all 3 operating mode, you can press the Menu button once to access the menu settings for that particular mode, and press twice to display System Setting Menu. The System Setting Menu is common to all modes.
Press UP and DOWN to scroll through the various setting options and press OK to select and confirm selection, Press MENU again to exit the setting menu.
- Ikon for videotilstand
- Status for loopoptagelse
- Motion Detection
- Optagelsesindikator
- Video Lock Status
- WDR Status
- G-Sensor Status
- Optagelseslængde
- Videoopløsning
- Rear screen
- Parkeringsmonitorstatus
- Hukommelseskortstatus
- Strømstatus
- Bilplade nummer
- Status for lydoptagelse
- Dato og klokkeslæt
Løsning: Adjust recording video resolution, 1080P/ 720P/ VGA available. When connected to the rear camera, recording video resolution: 1080P+720P/720P+720P/VGA+VGA Loop Recording: This function allows you to set video length to 1/3/5minutes, select a value to activate loop recording, so when storage is full, it will automatically loop back to the earliest file and record over it.
WDR: Wide Dynamic Range: turn on to optimize video quality with wider light range and image details.
Motion Detection: Turn ON/OFF motion detection function. In the video mode, in the standby state, when the front camera screen changes, the driving recorder will automatically record for 11 seconds .
Lydoptagelse: Turn ON/OFF audio recording in video. Date Stamp : Enable/Disable the date and time marks in video files.
G-Sensor: G-sensor will detect significant or sudden shock and movement, then automatically locks current file from loop recording. Low/Medium/High sensitivity available.
Parkeringsmonitor: It’s used to protect your car after parking. With this function on, after you stop the car and the camera turns off, it stays standby. When camera detects collision, it will automatically turn on and take a short video, then shut down automatically.
Car Number: Turn on to stamp your car plate number in video.
Photo Taking Mode
The CE18A camera can operate in Photo Taking Mode, and take HD photo up to 12 Mega pixels.
Sådan tager du et billede:
Simply power on the CE18A camera. Press Mode to select Photo Mode, and press OK to take photo.
Like the Video Recording Mode, you can press the menu button once to access the setting menu for Photo Mode, press menu twice to enter system setting menu.
- Fototilstand
- Anti-shake
- Foto opløsning
- Photo Counts
- Hukommelseskortstatus
- Strømstatus
- Date& Time
Løsning: Set the photo resolution, Up to 12MP available.
Anti-shake: Turn on to stabilize photo, reduce shaking.
Dato St.amp: Enable/Disable the date and time stamp in photo.
Afspilningstilstand
Denne tilstand giver dig mulighed for at afspille optaget video eller view fotos.
- Stop video recording, press and hold Menu button twice to switch to Playback Mode.
- Brug OP og NED -knappen til at rulle gennem den optagede files/ fotos, og tryk på OK for at view optaget video.
After choosing a recorded video or photo, press the Menu button once to access the setting menu for Playback Mode.
Slette: Slet den aktuelle file displayed or delete all files.
Beskyttelse: Lock/Unlock the current file displayed or Lock/ Unlock all files.
Slideshow: Select a time gap to activate this function, and all recorded file will be displayed in slide show.
Press MENU button twice to access System Setting Menu in any mode. The TOOL icon is highlighted in the upper left corner.
Pauseskærm: Indstil tiden til automatisk at slukke for LCD-displayet efter ingen handling.
Automatisk slukning: Set the time for the camera to automatically power off to save energy. After the camera is idle for set time, it will power off.
Frekvens: Set light frequency to 50Hz or 60Hz, and press OK. Beep Sound: Turn on/off sounds when you press any buttons.
Sprog: Chinese/English/Japanese/Deutsh/French/ Italian/Spanish
Dato / tid: Change the time and date by using the UP and DOWN button, then press OK to confirm.
Format: Format the Micro SD card.
Standardindstilling: Reset all settings back to factory default.
Version: Kontroller firmwareversion.
Specification
| Model | Toguard CE18A |
| Image Sensor | Høj opløsning CMOS-sensor |
| Skærm | 2.45 inch LCD Display |
| Linse | 170° High-Resolution Wide Angle Lens |
| Video Resolution | 1920*1080P+1280*720P/ 1280*720P+1280+720P/ 640*480P+640*480P |
| Video Format | MOV |
| Video Coding | H.264 |
| Picture Format | JPG |
| Photo Resolution | 12MP / 10MP / 8MP / 5MP /3MP/2MP/
1.3MP/VGA |
| Loop Recording | Understøttet |
| Power on recording | Understøttet |
| WDR | Understøttet |
| G-sensor lås | Understøttet |
| Sprog | Chinese/English/Japanese/Deutsh/ French/Italian/Spanish |
| Lydoptagelse | Indbygget mikrofon, Til / Fra valgfri |
| Opbevaring | Micro SD-kort (op til 32 GB) |
| USB-interface | Mini USB |
| Operativsystem | Windows 7/10 eller MAC |
| Intern strøm | Indbygget Li-ion batteri |
| Ekstern strømforsyning | DC 5V / 1.5A |
| Storage temperature | -4 ° C ~ 140 ° C (-20 ° F ~ 60 ° F) |
| Driftstemperatur | 14°F~122°F（-10°C~50°C） |
Almindelige problemer og løsninger
- Q: Even though set the screen saver, but the screen will randomly.
A: The power supply might not be stable, please change another car charger to try. - Q: Why dash cam drain car battery?
A: Please check whether the cigarette lighter still be on after you turn off car engine. - Q: The camera keeps starting and off?
A: That could be the parking monitor function being triggered, check the setup menu. - The dash cam will stop automatically while recording.
- A: Check whether the memory card is full.
- Check whether the Micro SD card is high-speed above C10.
- Kontroller hukommelseskortet, der er muligvis for mange låste videoer til, at loop-optagelsen ikke fungerer korrekt.
- Check the car charger connection status, if the connection is loose, the power supply is not stable, the camera will automatically turn off.
- If the video played on the computer is somehow not fluent or jammed.
- A: Try to play the video with other video players, like : Pot player or VLC player.
- Formater dit Micro SD-kort i kameraet.
- Run speed test on the memory card to make sure the memory card fits the requirement: Write Speed is over 10MB/S.
- Q: There are stripes interference in the image. There should be wrong light frequency.
A: According to the local main frequency, make the appropriate settings 50HZ or 60HZ. - Suction mount cannot attach on windshield well?
- A: Please clean the windscreen where attaching with a glass cleaning wipe. Removed the protective film, If it does not work, warming your windscreen then try it again.
- Please soak suction mount to warm water for a moment.
- If it is still not working, we are glad to send a new suction mount to you, please contact us ([e-mail beskyttet]) to get a replacement.
- Q: Without external power supply, the camera only lasts very short time, or it just can’t turn on.
A: The built-in battery is very small for safety reasons, not designed to work alone, so please keep it connected to external power supply. - Q: When connect the camera with PC by USB cable, it will show “Mass Storage” and “PC Camera”, I kannot do any thing.
A: In this situation, you can directly playback video on PC. If you want to operate camera, please connect it with cigarette lighter by car charger we provided.
Not having a positive experience?
Kontakt os venligst
We will offer prompt and authoritative reply within 24 hours and try our best to resolve your problem ASAP. More Safe Guarantee with Toguard!
Dokumenter/ressourcer
 |
TOGUARD CE18A Dash Camera [pdf] Brugervejledning CE18A Dash Camera, CE18A, Dash Camera |
