1. Introduktion
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Philips ICN-2S28-N Centium Electronic Ballast. This ballast is designed for use with two F28T5, F21T5, or F14T5 fluorescent lamps, and can also operate single lamps. Please read this manual thoroughly before installation and retain it for future reference.
2. Sikkerhedsoplysninger
ADVARSEL: Risk of electric shock. Installation should be performed by a qualified electrician in accordance with all national and local electrical codes. Disconnect power at the circuit breaker before installation or servicing.
- Sørg for, at strømforsyningen voltage matches the ballast's rated voltage (120V eller 277V).
- The ballast case must be properly grounded.
- Monter lamps within 1/4 inch of a grounded metal reflector.
- Maks. Voltage for RED-BLUE leads is 500 Vrms.
- Insulate YELLOW leads for 600V.
- Only use rapid-start sockets with this ballast.
- Do not modify the ballast or its wiring.
- This ballast is a Semi-Conducteur, High Power Factor, Class P, Sound Rated A, Type 1 Outdoor, with Inherent Thermal Protection. It contains no PCB's.
3. Pakkens indhold
Kontroller, at alle komponenter er til stede, før installationen påbegyndes:
- 1 x Philips ICN-2S28-N Centium Electronic Ballast
Image 1: Philips ICN-2S28-N Centium Electronic Ballast with its integrated wiring.
4. Opsætning og installation
Følg disse trin for korrekt installation af ballasten:
- Afbryd strømmen: Before starting any work, ensure the main power supply to the fixture is turned off at the circuit breaker.
- Mount the Ballast: Securely mount the Philips ICN-2S28-N ballast within the fixture. Ensure the ballast case is grounded.
- Ledningsforbindelser: Refer to the wiring diagram on the ballast label and the instructions below.
Billede 2: Detaljeret view of the ballast label, including wiring diagram and technical specifications.
Detaljer om ledningsdiagram:
- Input Power (120V or 277V):
- Tilslut SORT ledning til Line (L) indgangen.
- Tilslut HVID ledning til neutralindgangen (N).
- Lamp Connections (for 2 Lamps):
- Tilslut BLÅ wires to one end of each lamp.
- Tilslut RØD wires to the other end of each lamp.
- Tilslut GUL wires to the remaining terminals of the lamps.
- Jording: Ensure the ballast case is properly grounded to the fixture's metal housing.
Vigtige bemærkninger:
- This ballast is compatible with (2) F28T5, (2) F21T5, and (2) F14T5 lamps. It also works for single lamps.
- Monter lamps within 1/4 inch of a grounded metal reflector for optimal performance and safety.
- Insulate any unused YELLOW leads for 600V.
- Only use rapid-start sockets.
Image 3: The ballast with its color-coded wires clearly visible for connection.
5. Betjening
Once the Philips ICN-2S28-N Centium Electronic Ballast is correctly installed and wired, operation is straightforward:
- After completing the installation, restore power to the circuit at the breaker.
- Turn on the light switch connected to the fixture. The ballast will automatically ignite and regulate the power to the fluorescent lamps.
- The ballast is designed for programmed start, ensuring optimal lamp liv.
6. Vedligeholdelse
The Philips ICN-2S28-N Centium Electronic Ballast is designed for long-term, reliable operation with minimal maintenance. However, periodic checks can help ensure continued performance:
- Strømafbrydelse: Afbryd altid strømmen, før du udfører vedligeholdelse eller inspektion.
- Rensning: Keep the ballast and fixture free from dust and debris to ensure proper heat dissipation. Use a dry, soft cloth for cleaning.
- Ledningsinspektion: Periodically inspect wiring connections for any signs of wear, fraying, or loose connections. Ensure all connections remain secure.
- Lamp Udskiftning: Ved udskiftning af lamps, ensure they are of the correct type and wattage as specified for this ballast (F28T5, F21T5, F14T5).
- Miljøforhold: Ensure the ballast operates within its specified temperature range and environmental conditions (Type 1 Outdoor).
7. Fejlfinding
If your fluorescent fixture is not operating correctly, consult the following troubleshooting guide:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lamps lyser ikke. | Ingen strøm til armaturet. Forkert ledningsføring. Defekt lamps. Defekt ballast. | Kontroller afbryderen og vægafbryderen. Verify all wiring connections against the diagram. Udskift lamps with new ones of the correct type. Hvis lamps are new and wiring is correct, replace the ballast. |
| Lamps flimrer eller er svag. | Løse ledningsforbindelser. Forkert lamp type. Aldring lamps. Ballast nearing end of life. | Kontroller og fastgør alle ledningsforbindelser. Sørg for korrekt lamp types (F28T5, F21T5, F14T5) are used. Udskift lamps. Consider replacing the ballast. |
| Ballast makes humming noise. | Normal drift (let brummen). Løs montering. Overophedning. | A slight hum is normal for some ballasts. Ensure ballast is securely mounted. Check for proper ventilation and ensure ballast is not covered. If hum is loud or new, inspect for issues. |
If troubleshooting steps do not resolve the issue, contact a qualified electrician or Philips customer support.
8. Specifikationer
Below are the technical specifications for the Philips ICN-2S28-N Centium Electronic Ballast:
- Modelnummer: ICN-2S28-N
- Mærke: PHILIPS (Advance Ballast)
- Input bindtage: 120V / 277V
- Kompatibel Lamps: (2) F28T5, (2) F21T5, (2) F14T5 (also works for single lamps)
- Wattage: 28 watts (for F28T5 lamps)
- Lyskildetype: Fluorescerende
- Strømkilde: Elektrisk med ledning
- Materiale: Plast
- Farve: Sort
- Form: Rektangulær
- Udfør type: Sort
- Monteringstype: Rack Mount
- Varens vægt: 9.6 ounce
- Emnemål (L x B x H): 9.5 cm x 1.25 cm x 1 cm
- UPC: 781087080726
- Certificeringer: UL Listed 704G, CSA (NRTL/C)
- Funktioner: IntelliVolt (120V to 277V 50/60Hz), Programmed Start, High Power Factor, Class P, Sound Rated A, Type 1 Outdoor, Inherent Thermal Protection, No PCB's.
Billede 4: Side view of the ballast, illustrating its compact dimensions and mounting points.
9. Garanti og support
This Philips ICN-2S28-N Centium Electronic Ballast comes with a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or contact Philips customer support.
For technical assistance or support, please contact Philips directly. Technical information is often available via their official webwebsted eller ved at ringe til deres supportlinje.
- Fabrikant: Advance Ballast (a Philips company)
- Teknisk information: 1.800.372.3331 (as seen on product label)
- Online support: Besøg den officielle Philips website for product support and resources.