ARRIS Jumper T20S V2 Radio Controller Instruktionsmanual

Indledning

This manual provides detailed instructions for the setup, operation, and maintenance of your ARRIS Jumper T20S V2 Radio Controller. Please read this manual thoroughly before using the device to ensure proper function and safety.

Nøglefunktioner

• RDC90 Sensor Gimbals: Experience precise and sensitive control for your RC devices.
• Vivid OLED Screen Display: Stay informed with crucial flight data, telemetry, and settings on a high-resolution screen.
• ELRS and EdgeTX Compatibility: Benefit from reliable, extended-range communication and advanced firmware capabilities.
• Multi-Protocol Support: Connect effortlessly to a wide array of RC models and brands.
• Customization for Personalized Flying: Tailor your control setup with configurable switches, buttons, and functions via EdgeTX.

Produkt overview

Familiarize yourself with the components and design of your Jumper T20S V2 Radio Controller.

Billede: Forside view of the Jumper T20S V2 Radio Controller, showing the gimbals, OLED screen, power button, and various control switches and buttons.

Billede: Vinklet front view of the Jumper T20S V2 Radio Controller, highlighting the gimbals and control layout.

Billede: Side view of the Jumper T20S V2 Radio Controller, showing the foldable antenna in an extended position.

Billede: Bagside view of the Jumper T20S V2 Radio Controller, displaying the external cooling fan and battery compartment area.

Image: Diagram illustrating the airflow and cooling fan system integrated into the Jumper T20S V2 for high-power ELRS operation.

Billede: Nærbillede view of the omnidirectional foldable antenna, designed to provide stable signal support in all directions.

Opsætning

1. Batteriinstallation

1. Open the battery compartment cover located on the rear of the controller.
2. Insert two 21700 batteries, ensuring correct polarity.
3. Luk batterirummets dæksel forsvarligt.

2. Første opstart

1. Press and hold the power button (located centrally on the front panel) until the OLED screen illuminates.
2. The controller will boot into the EdgeTX operating system.

3. Gimbal Calibration (Recommended)

For optimal performance, it is recommended to calibrate the gimbals after initial setup or if you experience inconsistent control. Refer to the EdgeTX documentation for detailed calibration procedures.

Betjeningsvejledning

1. Navigations- og menusystem

The Jumper T20S V2 utilizes the EdgeTX firmware. Navigation is primarily done using the scroll wheel and menu buttons. The OLED screen displays all relevant information.

• Scrollhjul: Used to navigate through menus and adjust values.
• Menuknapper: Access various settings and functions.
• Systemmenu: Configure global settings, model setup, and radio calibration.

2. Model Setup and Binding

For at styre en RC-model skal du først oprette en modelprofilfile and bind the controller to the receiver.

1. Navigate to the Model Select screen in EdgeTX.
2. Opret en ny model, eller vælg en eksisterende.
3. Configure the internal or external RF module settings (e.g., ELRS, Multi-Protocol) to match your receiver.
4. Initiate the binding process on both the controller and the receiver according to their respective manuals.
5. Verify successful binding by checking receiver telemetry or control response.

3. Customizing Controls

The Jumper T20S V2 offers extensive customization. You can assign functions to switches, buttons, and sliders through the EdgeTX firmware.

• Access the Mixer and Special Functions menus within EdgeTX to configure control assignments.
• Adjust gimbal tension and stick settings by disassembling the radio, if desired (refer to advanced user guides for detailed instructions).

Opretholdelse

• Rensning: Brug en blød, tør klud til at rengøre controllerens yderside. Undgå slibende rengøringsmidler eller opløsningsmidler.
• Opbevaring: Store the controller in a cool, dry place, away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
• Firmwareopdateringer: Regularly check for and install the latest EdgeTX firmware updates to ensure optimal performance and access new features. Refer to the official EdgeTX webwebsted for instruktioner.
• Gimbalpleje: Keep gimbals free from dust and debris. Avoid applying excessive force.

Fejlfinding

Controlleren tænder ikke:

Ensure batteries are correctly installed and fully charged. Check battery polarity.

No response from RC model:

Verify that the controller is properly bound to the receiver. Check model settings in EdgeTX for correct RF protocol and channel assignments. Ensure the RC model's battery is charged and connected.

OLED screen is blank or flickering:

Restart the controller. If the issue persists, ensure firmware is up to date. Contact support if the problem continues.

Gimbal movement is erratic:

Perform a gimbal calibration through the EdgeTX system menu. Check for any physical obstructions or damage to the gimbals.

Specifikationer

Garanti og support

For garantioplysninger og teknisk support henvises til den dokumentation, der fulgte med dit køb, eller besøg den officielle ARRIS webwebsted. Gem din købsbevis til garantikrav.

For further assistance with EdgeTX firmware, visit the official EdgeTX project website and community forums for comprehensive resources and community support.