TecTake 403238 / 800747 Drejelig Kontorstol Brugsanvisning

Indledning

This manual provides detailed instructions for the assembly, operation, and maintenance of your TecTake 403238 / 800747 Swivel Office Chair. Please read these instructions carefully before assembly and use to ensure proper function and longevity of your product. This ergonomic office chair is designed for comfort and support during extended periods of sitting, featuring a padded seat, backrest, and headrest, along with adjustable height and tilt functions.

Image: The TecTake 403238 / 800747 Swivel Office Chair, showcasing its black faux leather upholstery, padded armrests, and five-star base with casters.

Sikkerhedsinstruktioner

To prevent injury or damage to the chair, please observe the following safety guidelines:

• Ensure all components are securely fastened before use. Regularly check and tighten screws.
• Do not exceed the maximum weight capacity of the chair (refer to specifications).
• Undgå at stå på stolen eller bruge den som skammel.
• Keep hands and fingers clear of moving parts, especially during height and tilt adjustments.
• Brug stolen på en plan overflade for at forhindre den i at vælte.
• Hold emballagematerialer væk fra børn for at forhindre kvælningsfare.
• Udsæt ikke stolen for direkte sollys eller ekstreme temperaturer, da dette kan beskadige materialet.

Komponentliste

Før monteringen påbegyndes, skal du kontrollere, at alle dele er til stede og ubeskadigede. Hvis der mangler eller er beskadigede dele, må du ikke fortsætte med monteringen, men kontakte kundesupport.

• Ryglæn
• Sædepude
• Armlæn (venstre og højre)
• Mechanism Plate (under seat)
• Gas Lift cylinder
• Gasliftdæksel
• Femstjernet base
• Hjul (5 stk.)
• Hardware (skruer, skiver, unbrakonøgle)

Monteringsvejledning

Follow these steps to assemble your office chair. It is recommended to assemble the chair on a soft, clean surface to prevent scratches.

Step 1: Attach Casters to the Base

Insert each of the five casters into the holes at the end of each leg of the five-star base. Push firmly until they click into place.

Step 2: Insert Gas Lift

Place the gas lift cylinder into the central hole of the five-star base. Then, slide the gas lift cover over the gas lift cylinder.

Step 3: Attach Mechanism Plate to Seat

Align the mechanism plate with the pre-drilled holes on the underside of the seat cushion. Ensure the adjustment lever faces the front of the seat. Secure it with the provided screws and tighten them using the Allen key.

Image: Close-up of the chair's adjustment lever, indicating its function for height and tilt control. This lever is part of the mechanism plate that attaches to the seat.

Step 4: Attach Armrests to Seat and Backrest

Attach the armrests to the sides of the seat cushion using the designated screws. Do not fully tighten yet. Then, align the backrest with the armrests and secure it with screws. Once all screws are in place, tighten them evenly and securely.

Trin 5: Tilslut sædeenheden til gasløfteren

Carefully place the assembled seat and backrest onto the gas lift cylinder. The tapered end of the gas lift will fit into the central hole of the mechanism plate. Press down firmly on the seat to ensure a secure connection.

Billede: Forside view of the fully assembled TecTake office chair, highlighting the padded seat, backrest, and armrests.

Your TecTake office chair is now assembled. Before use, ensure all connections are tight and the chair is stable.

Betjeningsvejledning

Your TecTake office chair offers several adjustments to customize your seating experience:

Højdejustering

To adjust the seat height, locate the lever on the right side, beneath the seat.

• For at hæve sædet: Løft håndtaget, mens du aflaster sædet. Sædet hæves automatisk. Slip håndtaget i den ønskede højde.
• Sådan sænkes sædet: Lift the lever while remaining seated. The seat will lower. Release the lever at the desired height.

Tilt Function and Lock

The chair features a tilt mechanism allowing the backrest and seat to recline together.

• To enable tilt: Pull the same lever (used for height adjustment) outwards from the chair. The chair will now allow you to recline.
• To lock tilt: Push the lever inwards towards the chair. The chair will lock in its upright position.

Image: An illustration demonstrating the range of height adjustment and the reclining tilt function of the office chair.

Justering af hældningsspænding

Beneath the seat, at the front, there is a round knob. This knob controls the tension of the tilt mechanism.

• To increase tension (harder to recline): Drej knappen med uret.
• To decrease tension (easier to recline): Drej knappen mod uret.

Opretholdelse

Regelmæssig vedligeholdelse vil forlænge levetiden og udseendet af din kontorstol.

• Rensning: Tør kunstlæderbetrækket af med en blød kludamp cloth. For stubborn stains, use a mild soap solution and wipe dry immediately. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the material.
• Ramme og base: Wipe metal and plastic parts with a damp klæde.
• Hjul: Periodically clean casters to remove hair, dust, and debris that may hinder smooth movement.
• Hardware: Every 3-6 months, check all screws and bolts to ensure they are tight. Retighten as necessary to maintain stability and safety.
• Undgå overbelastning: Do not exceed the chair's stated weight capacity.

Fejlfinding

Hvis du støder på problemer med din stol, kan du se følgende almindelige problemer og løsninger:

• Stolens knirken:

  Check all screws and bolts and tighten them. A small amount of silicone lubricant can be applied to moving metal parts, avoiding contact with plastic or upholstery.
• Stol kan ikke justeres i højden:

  Ensure the gas lift lever is fully engaged. If the issue persists, the gas lift cylinder may be faulty and require replacement. Contact customer support.

• Stolen føles ustabil/vaklende:

  Verify that all screws, especially those connecting the armrests to the seat and backrest, are securely tightened. Ensure the gas lift is properly seated in the base and mechanism plate.

• Hjulene ruller ikke jævnt:

  Remove any hair, dust, or debris that may be caught in the caster wheels. Clean the wheels and axles. Ensure the casters are fully inserted into the base.

Specifikationer

Dimensioner (omtrentlig)

Image: Technical drawing illustrating the approximate dimensions of the TecTake office chair in centimeters. Key measurements include seat width (55 cm), seat depth (52 cm), backrest width (48 cm), adjustable seat height (47-55 cm), and overall height (115-123 cm).

• Overall Height: 115-123 cm
• Seat Height (adjustable): 47-55 cm
• Sædebredde: 55 cm
• Sædedybde: 52 cm
• Backrest Width: 48 cm
• Armrest Height (from seat): 68.5-76.5 cm
• Bunddiameter: 67 cm

Garanti og support

Specific warranty information for the TecTake 403238 / 800747 Swivel Office Chair is not provided in this document. For details regarding warranty coverage, spare parts availability, or technical support, please refer to the official TecTake website or contact their customer service directly. Information regarding spare parts availability was not provided in the product data.

Du kan besøge TecTake Brand Store on Amazon for mere information.