Einhell 4300345 TH-MS 2513 T Miter and Table Saw Instruction Manual

1. Introduktion

Thank you for choosing the Einhell TH-MS 2513 T Miter and Table Saw. This versatile power tool is designed for precise cutting of wood, plastic, and non-ferrous metals, offering both miter saw and table saw functionalities. This manual provides essential information for the safe and efficient operation, setup, maintenance, and troubleshooting of your saw. Please read these instructions carefully before first use and keep them for future reference.

Figur 1: Overview of the Einhell TH-MS 2513 T Miter and Table Saw.

2. Sikkerhedsinstruktioner

Always observe the following safety precautions to prevent electric shock, fire, and serious injury:

• Læs hele manualen: Forstå alle instruktioner og advarsler, før du bruger saven.
• Brug personlige værnemidler (PPE): Always wear safety glasses, hearing protection, and a dust mask. Use gloves when handling saw blades.
• Hold arbejdsområdet rent og godt oplyst: Rodede eller mørke områder inviterer til ulykker.
• Må ikke anvendes i eksplosive atmosfærer: Brug ikke elværktøj i nærheden af ​​brandfarlige væsker, gasser eller støv.
• Fastgør emnet: Altid clamp or hold the workpiece firmly to prevent movement during cutting.
• Brug den rigtige kniv: Ensure the saw blade is sharp, clean, and suitable for the material being cut. Never use damaged or dull blades.
• Oprethold korrekt fodfæste og balance: Gå ikke for langt.
• Afbryd strømmen: Always unplug the saw before making adjustments, changing accessories, or performing maintenance.
• Keep guards in place: Never operate the saw without all guards properly installed and functioning.
• Undgå utilsigtet start: Sørg for, at kontakten er i slukket position, før du tilslutter værktøjet.

3. Opsætning

3.1 Udpakning og inspektion

Carefully remove all components from the packaging. Inspect the saw for any damage that may have occurred during shipping. Do not operate the saw if any parts are damaged or missing. Contact customer support immediately.

3.2 Montering

The Einhell TH-MS 2513 T requires minimal assembly. Ensure all included components, such as the push stick and any necessary guards, are properly attached according to the diagrams in the separate assembly guide (if provided). The work table is made of lightweight and stable cast aluminum, designed for precise work.

3.3 Montering af savklinge

1. Afbryd strømmen: Sørg for, at saven er frakoblet strømkilden.
2. Open blade guard: Carefully lift or open the blade guard to access the blade arbor.
3. Install blade: Place the saw blade (Ø 250 x Ø 30 x 2.8 mm, 36 teeth) onto the arbor, ensuring the rotation direction indicated on the blade matches the arrow on the saw.
4. Secure blade: Fasten the blade with the provided washer and arbor nut, tightening securely.
5. Close guard: Return the blade guard to its original position.

Figure 2: Saw blade and protective guard in miter saw configuration.

4. Betjeningsvejledning

4.1 Generel drift

Before starting, ensure your workpiece is stable and properly supported. Always allow the blade to reach full speed before beginning a cut. Feed the material slowly and steadily. Never force the saw.

4.2 Miter Saw Function

The miter saw function allows for precise cross-cuts and miter cuts. Adjust the miter angle by loosening the locking knob, setting the desired angle (-45°/0°/+45°), and re-tightening the knob. For bevel cuts, adjust the saw head tilt. Ensure the workpiece is firmly against the fence.

• Skærekapacitet ved 90°: 130 x 75 mm
• Skærekapacitet ved 45°: 120 x 50 mm
• Cutting Capacity at 2 x 45° (Compound Miter): 70 x 35 mm

Figure 3: Adjusting the miter angle for precise cuts.

4.3 Table Saw Function

To use the saw as a table saw, lock the saw head in the upright position. Adjust the cutting height (0–40 mm) using the height adjustment mechanism. Use the parallel fence for rip cuts and the push stick for feeding smaller workpieces. The table surface measures 416 x 352 mm.

Figure 4: Adjusting the cutting height for table saw operation.

4.4 Støvudsugning

The saw is equipped with a dust funnel behind the saw blade for improved sawdust collection. Connect a suitable dust extractor to the dust port to maintain a clean work environment and improve visibility during operation.

Figure 5: Dust extraction port for connecting a vacuum system.

5. Vedligeholdelse

Regelmæssig vedligeholdelse sikrer savens levetid og sikker drift.

• Rensning: After each use, disconnect the saw from power and clean off sawdust and debris using a brush or compressed air. Do not use solvents that could damage plastic parts.
• Bladinspektion: Undersøg savklingen regelmæssigt for skarphed, revner eller manglende tænder. Udskift sløve eller beskadigede klinger med det samme.
• Vagtfunktionalitet: Ensure all guards move freely and return to their protective positions.
• Smøring: Apply a light coat of machine oil to moving parts as recommended in the full manual (if applicable).
• Strømledning: Check the power cord for damage. Do not use the saw if the cord is frayed or cut.

6. Fejlfinding

Dette afsnit omhandler almindelige problemer, du kan støde på. Kontakt kundesupport, hvis du har problemer, der ikke er nævnt her.

7. Tekniske specifikationer

8. Garanti og support

8.1 Garanti

This Einhell product comes with a 2 års garanti from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers defects in material and workmanship under normal use. It does not cover damage caused by misuse, abuse, unauthorized repairs, or normal wear and tear.

8.2 Kundesupport

For technical assistance, spare parts, or warranty inquiries, please contact Einhell customer support. You can find contact information on the official Einhell webhjemmeside eller gennem din lokale forhandler.

Webwebsted: www.einhell.com

Please have your model number (4300345) and serial number (if applicable) ready when contacting support.