Belimo FSLF24-S US Fire and Smoke Damper Actuator Manual

1. Introduktion

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Belimo FSLF24-S US Fire and Smoke Damper Actuator. This device is designed for the reliable control of fire and smoke dampers in ventilation and air conditioning systems, ensuring safety in critical building environments. Please read this manual thoroughly before proceeding with installation or operation.

2. Sikkerhedsoplysninger

ADVARSEL:

• Installation og vedligeholdelse må kun udføres af kvalificeret personale.
• Disconnect all power before installing or servicing the actuator to prevent electric shock.
• Sørg for, at al ledningsføring overholder lokale og nationale elektriske forskrifter.
• Betjen ikke aktuatoren ud over den angivne volumen.tage and environmental limits.
• This actuator is a safety device; ensure it is installed correctly and tested regularly.

3. Pakkens indhold

Kontroller, at alle genstande er til stede og ubeskadigede ved udpakning:

• Belimo FSLF24-S US Fire and Smoke Damper aktuator
• Mounting Bracket/Hardware (if applicable)
• Instruktionsmanual (dette dokument)

4. Specifikationer

5. Opsætning og installation

The Belimo FSLF24-S US actuator is designed for panel mounting and requires careful installation to ensure proper function and safety. Always refer to the specific wiring diagrams provided with the product packaging for detailed electrical connections.

5.1 Montering af aktuatoren

1. Ensure the mounting surface is clean, dry, and capable of supporting the actuator's weight.
2. Position the actuator on the damper shaft according to the damper manufacturer's instructions.
3. Secure the actuator using appropriate mounting hardware, ensuring a firm and stable connection.
4. Kontroller, at damper can move freely without obstruction after mounting.

5.2 Elektriske forbindelser

The FSLF24-S US actuator operates on 24 Volts. Electrical connections should only be made by a licensed electrician in accordance with all applicable codes.

• Disconnect power to the circuit before making any connections.
• Connect the 24V power supply to the designated screw terminals on the actuator.
• Sørg for, at alle forbindelser er sikre og korrekt isolerede.
• Double-check wiring against the provided diagram to prevent damage to the actuator or system.

Figur 1: Front view of the Belimo FSLF24-S US Fire and Smoke Damper Actuator, showing its orange casing, control dial, and connection points. This image illustrates the general appearance and key features of the actuator for installation reference.

6. Betjeningsvejledning

The Belimo FSLF24-S US actuator is designed for automatic operation in conjunction with a fire alarm or building management system. It typically operates in a fail-safe mode, meaning it will drive the damper to a safe position (e.g., closed) upon loss of power.

6.1 Indledende opstart

1. After completing all electrical connections and mounting, restore power to the actuator.
2. Observe the actuator's initial movement. It should drive the damper to its default position (e.g., open or closed, depending on configuration).
3. Kontroller, at damper moves smoothly and without obstruction.

6.2 Funktionstest

Regular functional testing is crucial for fire and smoke dampers. Consult local fire safety regulations for required testing intervals.

• Initiate a test sequence from your building management system or fire alarm panel to activate the dampeh.
• Confirm that the actuator drives the damper to its intended fire/smoke safety position.
• Kontroller, at damper returns to its normal operating position once the test signal is removed.

7. Vedligeholdelse

The Belimo FSLF24-S US actuator is designed for long-term, reliable operation with minimal maintenance. However, periodic inspection is recommended.

• Årlig inspektion: Visually inspect the actuator and its connections for any signs of wear, damage, or corrosion.
• Funktionskontrol: Perform a functional test of the damper and actuator as per local regulations (e.g., NFPA 80, NFPA 105).
• Rensning: Keep the actuator free from dust and debris. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
• Ingen smøring nødvendig: The actuator is factory-lubricated and does not require additional lubrication.

8. Fejlfinding

If the actuator is not functioning as expected, consult the following table before contacting technical support.

9. Garanti og support

Belimo products are manufactured to high standards and typically come with a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Belimo webwebsted.

For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Belimo customer support or your authorized Belimo distributor. When contacting support, please have your product model number (FSLF24-S US) and serial number (if applicable) readily available.

Belimo Official Webwebsted: www.belimo.com