Document

MEAN WELL NPB-450 Series 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger User Manual

MEAN WELL Logo

NPB-450 Series

Nodweddion

  • Patented auto ranging with ultra-wide charging voltage (10.5~21V,21~42V,42~80V, 54~100V; Please refer to page 8 for setting)
  • Protocol CANBus adeiledig ar gyfer rheoli, gosod a monitro
  • Rhaglenadwy 2/3 stage a chromlin codi tâl trwy SBP-001
  • Gosodiad â llaw am 2/3 stage a 4 cromlin gwefru adeiledig trwy DIP SW
  • Amddiffyniadau lluosog:
    Short circuit / Over voltage / Over temperature/ Battery under voltage/ Battery reverse polarity (No damage)
  • Gwefrydd Iawn a Batri Llawn signal
  • Swyddogaeth iawndal tymheredd i ymestyn bywyd batri (asid plwm yn unig)
  • -30°C~+70°C wide operating temperature
  • Cefnogwr DC a reolir â thermol ar gyfer lleihau sŵn
  • Anghysbell AR / I FFWRDD rheoli
  • Smart programmer available (Order NO.: SBP-001, sold separately)
  • Affeithiwr handlen cario ar gael (Gorchymyn RHIF: DS-Carry handle, gwerthu ar wahân)
  • Cydymffurfio ag ardystiad deuol 62368-1 + 60335-1/-2-29
  • Yn addas ar gyfer batris asid plwm (Pb) a li-ion
  • 3 mlynedd warant

ceisiadau

  • AGV
  • E-feic, E-Sgwter, Camping car, Bws, cerbydau arbenigol
  • Peiriant torri lawnt robotig
  • Robot golchi
  • Cychod hamdden, cwch hwylio personol neu gwch gwaith
  • System wyliadwriaeth
  • Gorsaf sylfaen telathrebu
  • Datrysiad wrth gefn system radio
  • Equipments or instruments with backup battery

Disgrifiad

Mae NPB-450 yn gyfrol fechan, amlbwrpas ac uwch-eangtage intelligent charger. It utilizes a fully digital control design with patented automatic battery voltage dechnoleg canfod, gyda phum nodwedd allweddol gan gynnwys deallus, amlbwrpas, hawdd ei ddefnyddio, diogel a chryno. Mae gan y gyfres bedwar model gydag allbwn cyftage ranges of 10.5~21V, 21~42V, 42~80V, and 54~100V respectively. The charging voltagMae ystod pob model yn ddigon eang i gwmpasu amrywiaeth o wahanol gyfeintiau batritages a chemistries batri, ac mae adeiledig yn ddeallus cyftage dull codi tâl canfod (Sylwer bod y modd hwn wedi'i osod i OFF yn ddiofyn y ffatri ac mae'n addas ar gyfer batris lithiwm gyda BMS yn unig). Gall yr NPB-450 baru â rhaglennydd SBP-001 MEAN WELL ar gyfer cyfluniad digidol, fel dewis 2/3 stage codi tâl, addasu cyftage/cyfredol, a gosodwch amser cylch gwefru i amddiffyn oes y batri. Trwy'r DIP SW hawdd ei ddefnyddio ar y panel blaen, gall y defnyddiwr hefyd addasu'r 2/3 s yn uniongyrcholtage codi tâl, cerrynt (50 ~ 100%), a dewiswch rhwng y 4 math o gromliniau codi tâl rhagosodedig. Yn ogystal, mae protocol cyfathrebu CANBus wedi'i ymgorffori i fodloni cymwysiadau proffesiynol, sy'n caniatáu rheoli a monitro o bell ar gyfer statws y gwefrydd. O ran diogelwch, mae ganddo ganfod deallus ar gyfer batri cyftage and connection as well as protection from reverse polarity. It passes ITE IC/EN/UL62368-1 and household appliances EN60335-1/-2-29 dual safety and 3-year warranty to guarantee reliable operation. The NPB-450 is truly an intelligent, safe, and reliable universal charger with outstanding cost performance.

Amgodio Model

Manyleb

Manyleb

Manyleb Parhad

Diagram Bloc

PFC fosc : 80KHz
PWM fosc : 60KHz

Diagram Bloc

Cromlin Derating

Cromlin DeratingDerating Curve Continued

Nodweddion Statig

Nodweddion Statig

Llawlyfr Swyddogaeth

1. Gosod â llaw

Gosodiad llawlyfr

1.1 2 or 3-stage selectable via DIP S.W on panel

2 or 3-stage selectable via DIP S-W on panel

1.2 Charging curve can be adjustable via DIP S.W on panel

Charging curve can be adjustable via DIP S-W on panel

  • The default curve is programmable, whereas other pre-defined curves can be activated by the means of the DIP S.W; This series provides 2 or 3 stage charging curve please refer to the table below and the Mechanical Specification.

Charging curve can be adjustable via DIP S-W on panel continued

2. Programmable charging curve

Charging Curve can be set via SBP-001 with computer

1 cam

Cyfluniad caledwedd

Cyfluniad caledwedd

2 cam

Connect to software for setting

Connect to software for setting

Connect to software for setting continued

Disgrifiad Swyddogaeth:

SBP-001 is a programmer, particularly for MEAN WELL’s various programmable battery charger models to program the parameters of charging curves, such as the 2 or 3 stage selectable, Constant current (CC), tapper current(TC), Constant voltage (CV), float voltage (FV),Charging time out and so on, to accommodate the diversified battery specification in industry. With the design accounting for simplicity and convenience, users can easily configure MEAN WELL’s programmable battery chargers with SBP-001 programmer and the computer; all of the setups are able to be finished easily by the means of the specific software.
Note:(1) Tapper current(TC) default is 10%, can be fine tuned from 2% to 30% by SBP-001 with computer or CANBus Interface.
(2) Please contact MEAN WELL for more details.

※ Software Interface:

Rhyngwyneb Meddalwedd

3. Auto Ranging for Charging (Default non-Auto ranging)

※ Function Description:

a. NPB-450 has built-in auto ranging mode.
(Note this mode is set to OFF by factory default and is suitable for lithium batteries with BMS only)

b. When operating in auto ranging mode , NPB-450 will automatically detect the voltage of battery that is connected and adjust charging voltage accordingly. It will not start charging unit appropriate battery voltage yn cael ei ganfod.

c. While under auto ranging mode, NPB-450’s built-in MCU will adjust charging voltage. There is no potentiometer for voltage adjustment on the front panel.

d. While under auto ranging mode, the charging current can be adjusted between 50~100%. (The charging current can not be adjusted via potentiometer while not operating in auto ranging mode)

※ When using the auto ranging charging curve function, please pay attention to the following:

Input-Output Side

  1. Default factory setting is OFF via DC output side DIP S.W, Follow steps A1~A6 below to enable the setting.
  2. Auto ranging function should use together with Lithium batteries and BMS (Battery Management System).
  3. Do not exceed the output voltage and current ranges as specified in the NPB-450 specifications (please refer to page 2).

※ Auto Ranging function by DIP S.W Setting

Auto Ranging function by DIP SW Setting

※ Back to non-auto ranging as following:

Non-auto ranging

4. Auto Derating function

※ Covered by over temperature protection, auto de-rating function works under operation either in charging curve (2 or 3 stage) or under control by communication protocol(CANBus).

T1(Typ.): Maximum ambient temperature of 100% output current.
T2(Typ.): T1+5℃.

Auto Derating function

5. CANBus communication interface

CANBus 2.0B version, Can control, setting and monitoring that including output charging voltage, output charging current, internal temperature and DC output ON/OFF……and so on, please refer to the llawlyfr defnyddiwr am fwy o fanylion.

CANBus communication interface

CANBus communication interface continued

6. Charger OK Signal

Charger OK signal is a TTL level signal.
The maximum sourcing current is 10mA.

Charger OK Signal

7. Battery Full Signal

Battery full signal is a TTL level signal.
The maximum sourcing current is 10mA.

Battery Full Signal

8. Remote ON-OFF Control

The NPB-450 can be turned ON/OFF by using the “Remote Control” function.

Rheoli ON-OFF o bell

※ The charger is shipped, by factory default, with Remote ON-OFF(pin 7) and +12Vaux (pin 8) shorted by connector.

Remote ON-OFF Control continued

9. Temperature compensation (3 stage yn unig)

Temperature compensation function to prolong battery life for lead-acid batteries. Temperature compensation range is 0 ~ 40℃.
The battery temperature sensor comes along with the charger can be connected to the unit to allow temperature compensation of the charging voltage.
If the sensor is not used, the charger works normally.

Iawndal tymheredd

10. DC Output Side LED Indicators & Corresponding Signal at Function Pins

DC Output Side LED Indicators

Manyleb Mecanyddol

※ Intelligent Battery Charger model

Intelligent Battery Charger model

※ DIP S.W

DIP SW

※ Control Pin No. Assignment : HRS DF11-14DS or equivalent

Control Pin No Assignment

※ LED Status Table

Tabl Statws LED

※ Connector Pin No. Assignment : HRS DF11-14DS or equivalent

Connector Pin No Assignment

Swyddogaeth Pin

Note1: Non-isolated signal, referenced to [GND(signal)].
Note2: Isolated signal, referenced to GND-AUX

Rhestr Ategolyn

※ NTC Sensor and Remote Control mating along with NPB-450 (Standard accessory)

Rhestr Ategolyn

※ Carry handle (Optional accessory, battery charger and pull handle should be ordered seperately)

Accessory List Continued 1

Accessory List Continued 2

Llawlyfr Gosod

Cyfeiriwch at: http://www.meanwell.com/manual.html

Dogfennau / Adnoddau

MEAN WELL NPB-450 Series 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger [pdf] Llawlyfr Cyfarwyddiadau
NPB-450 Series, 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger, NPB-450 Series 450W High Reliable Ultra Wide Output Range Intelligent Battery Charger

cyfeiriadau

Gadael sylw

Ni fydd eich cyfeiriad e-bost yn cael ei gyhoeddi.