CURSOR Fitness
C20 Treadmill
User’s Manual
Important Precaution
 MINIMUNUSER HEIGHT | 140 cm |  MAXUSER WEIGHT | 265 Lbs |
WARNING
CORRECT LUBRICATION OF THE TREADMILL IS REALLY IMPORTANT. THIS LUBRICATION MUST BE PERFORMED REGULARLY DEPENDING ON EACH PERSON, EVEN BEFORE ITS FIRST USE.
YOU MUST PRESERVE THE ORIGINAL PACKAGING WITH ITS PROTECTIONS, PURCHASE RECEIPT, MANUAL, AND COMPONENTS DURING THE GUARANTEE PERIOD.
In order to decrease the risk of suffering severe injuries, read carefully all the important instructions and warnings regarding the use of a treadmill before using it.
CURSOR FITNESS doesn’t take any responsibility for personal injuries or property damages resulting from the use of this product.
- Before starting any workout program, consult your doctor. It’s especially important for people older than 35 years old, people with a health problem, and pregnant women.
- Use the equipment as explained in the instructions manual.
- Keep the equipment in an enclosed area, away from dust or humidity. Don’t store it in a garage, indoor backyard, or near the water. Humidity, dust and water could lead to a malfunction of the equipment, annulling its guarantee.
- Place the unit on a flat surface. If the surface is uneven, the proper functioning could be affected. Some models include levelers or leveling threads behind the legs, helping the
leveling. Please read the manual to verify if your unit is provided with one of them… - The unit must be placed in a ventilated area. Don’t use it in places with sprays or oxygen dispensers. The air you breathe may be affected and cause an accident.
- Keep children younger than 12 years old and pets away from the equipment. Keep the security distance.
- Check in the manual the maximum weight your equipment can support. Excessive weight could lead to a malfunction in the operating system, which won’t be covered by the guarantee.
- If your equipment is working through a power supply: make sure that the power cord and plug are in good condition. Carry out the connection only when the circuit has a ground connection, otherwise, it could cause damages to the equipment or in the property which the guarantee won’t cover. Power cords must be away from hot surfaces.
- If it is a battery-powered unit: check and make sure that they are charged enough so the display will fully function.
- If your unit works with an electric supply: check the speed it can reach, for your security. The best is to adjust gradually the speed in order to avoid sudden changes.
- If your unit works through an electric supply: never leave the machine unattended while it’s working.
- Check and tighten all screws on a regular basis, because due to vibrations screws and nuts tend to loosen. Damages caused by a lack of maintenance won’t be covered by the guarantee.
- Two people will be needed in order to take the unit from the package. Otherwise, the damages caused at this moment won’t be covered by the guarantee.
- Don’t let any object fall into the grooves.
- If the unit works through a power cord: unplug always the power cord before cleaning it, after the workout, and before performing any maintenance duty.
- If you start feeling pain or dizziness while training: STOP IMMEDIATELY.
- You must preserve the original packaging with its protections, manual, and components during the guarantee period.
- This electronic product can’t be thrown under any circumstances into municipal rubbish bins. With the aim of preserving the environment, this product must be recycled according to the applicable law of your country. Please contact your town council to know more about this procedure.
- Should you need technical assistance or advice with the installation of pieces, You can get in touch with us through 866-950-8629.
YOU MUST KEEP THE PURCHASE RECEIPT IN ORDER TO HAVE ACCESS TO THIS SERVICE KEEP THIS ADVICE FOR FUTURE REFERENCES
Main Technical Features
| Input Voltage | 110V±10% |
| Frequency | 60 HZ |
| Running Area | 39.8″ x 15.4″ |
| Function | Remote control, Bluetooth, APP |
| Speed Range | 0.6-3.9MPH |
| Max user weight | 265 Lbs |
| Power | 2.5 HP |
Assembly
Plug and Play, No assemble needed
| No. | Fittings | Qty |
| 1 | Remote Control | 1 |
| 2 | Lubricant | 1 |
| 3 | Multi- wrench | 1 |
| 4 | 5mm wrench | 1 |
| 5 | 6mm wrench | 1 |
| 6 | CR2032 Lithium Battery | 1 |
Workout Guidelines
Beware:
Before starting to use this or any exercise programs, consult your doctor. This is especially important for people older than 35 years old, or for people with health problems.
Programm with warm-up workouts:
Warm-up: Start stretching and slightly activating the muscles between 5 and 10 minutes. The warm-up will increase your corporal temperature, your heart rate, and your blood flow, making you ready for the workouts.
- WORKOUT FOCUSED ON THE TRAINING AREA: Do some exercises during 20-30 minutes with your heart rate (don’t maintain your heart rate for more than 20 minutes during the first weeks of the exercise program). Breathe constantly and deeply during the workout (never hold your breath).
- COOL DOWN: Finish with stretching exercises during 5-10 minutes. Stretching increases the flexibility of your muscles and helps you to avoid injuries after the workouts.
FREQUENCY OF THE WORKOUT:
In order to be fit or improve your shape, complete three workout sessions each week, with a rest day between the workouts. After some months of regular training, you will be able of completing up to five workouts a week.
Treadmill Operation
A brief introduction
This electronic watch is easy to use and has few adjustment parameters The noun convention used in the specification:
Treadmill parameters: “Speed” values Motion parameters: “distance” value, “calorie” value, “time” value. Motion mode: wireless receiving control mode
LED screen display description:
- Speed display: When this LED is on, the screen displays the current speed value.
- Time display: When this LED is on, the screen shows the current time value.
- Distance display: When this LED is on, the screen shows the current distance value.
- Calorie display: When this LED is on, the screen shows the current calorie value of the exercise.
The above parameters are displayed at intervals of about 5 seconds.
This product is a wireless remote control, and the Settings are as follows:
- Start button: Press the start button on the remote control and the treadmill belt begins to move.
- Pause button: Press the pause button on the remote control to pause the treadmill belt’s movement. The display window will show “PAU” and pause the current time, distance, calories, speed, etc. Press the start button on the remote control to continue the current status and resume exercising.
- Speed +: Press the speed + button on the remote control to increase the exercise speed.
- Speed -: Press the speed – button on the remote control to decrease the exercise speed.
- P button: Press the P button on the remote control to switch the display window between exercise speed, time, distance, and calories.
- Power button: Press the power button on the remote control to start exercising.
- Stop button: Press the stop button on the remote control to stop exercising.Please note that if the movement time exceeds 99 min 59s, the system will stop automatically.
Trouble Shooting
| Error Code | Reason | Solution |
| E01 | Communication error | Re-plug each plug of the signal line |
| Replace the electronic meter | ||
| Replace the driver | ||
| E02 | Sensor detection error | Detect sensor route |
| Change motor | ||
| Change PCB | ||
| E03 | Over current protection | Change PCB |
| E04 | Sudden big current protect | Check the AC power supply voltage |
| Change PCB | ||
| E05 | Sudden low current protect | Check the AC power supply voltage |
| Change PCB | ||
| E06 | Overload error | Check running belt resistance |
| Change motor | ||
| Change PCB | ||
| E08 | PCB overheat protection | Check running belt resistance |
| Change PCB | ||
| E09 | Motor testing error | Turn off and re-start machine Change motor |
| E11 | Motor wire not well connected | Check motor wire |
| Change PCB | ||
| Change motor | ||
| E12 | PCB error | Change PCB |
| E13 | Computer error | Check connection wire |
| Change PCB | ||
| Change computer | ||
| E14 | Phase failure error | Re-plug the phase wire into the drive |
| Power off and on | ||
| Replace the motor | ||
| E16 | Drive failure | Replace the motor |
The Obvious Danger List
| No. | Description | Associated |
| 1. | Mechanical Hazards | |
| 1.1 | Crushing | Inclining |
| Folding | ||
| 1.2 | Shearing | Inclining |
| Folding | ||
| 1.3 | Drawing-in Or Trapping | Rear roller |
| Drive system | ||
| 1.4 | Falling | Sudden starts/stops |
| Excessive speed variation | ||
| Support failure | ||
| 1.5 | Abrasion | Contact with moving running surface |
| 1.6 | Slippery Surface | Slipping and falling |
| 1.7 | Stored Energy | Folded treadmills falling down |
| Springs or elastic devices prior to assembly | ||
| 2. | Electrical Hazards | |
| 2.1 | Electrocution | Contact with live components |
| 3. | Thermal Hazards | |
| 3.1 | Burns | Contact with hot surfaces |
| 4. | Hazards generated by neglecting ergonomic principles in design process | |
| 4.1 | Ineffective ergonomics | Size or location of support surfaces |
| Running surface dimensions | ||
| 4.2 | Human errors human behaviour | Reasonably foreseeable misuse |
| 5. | Noise Hazards | |
| 5.1 | Disturbing acoustic communication | Moving treadmill motor and belt |
Maintenance
This product must be earthed. If the power cord is damaged, it must be replaced with a manufacturer-recommended power cord.
DO NOT TANGLE THE POWER CORD
Regular maintenance of the treadmill
- STORAGE: Keep your equipment in an enclosed place, away from dust or humidity. Don’t store it either in a garage or in an indoor backyard, or near the water. Humidity, dust, and water could damage it and affect its functioning
- ELECTRIC CABLE: Make sure that the cable and plug are in perfect condition. Electric cables must be away from hot surfaces
- SCREWS AND CONNECTING CABLES: Supervise and tighten the screws on a regular basis, because due to the vibration the screws and nuts tend to loosen.
Lubrication: After running for a period of time, the treadmill must be configured with lubricants for lubrication.
Schedule:
| < 3 hours/week | 2 months |
| 4 – 7 hours/week | 1 month |
| > 8 hours/week | 15 days |
*Do not lubricate more than what you need to. Remember: regular and reasonable lubrication is to improve the lifespan of your treadmill.
Whether it is necessary to lubricate, make sure the machine is switched off and unplug the electricity. Lift the running belt, and observe if there is any silicon remaining on the running board which is under the running belt. If it is dry, then you need to apply the lubricant.
a) The step to lubricate the running board is as follows: (see the above figure)
b) Stop the running belt.
c) Turn over the running belt. Insert the lubricant pot as deep as possible into the middle of the running belt. Apply the lubricant onto the inner side of the running belt. Lubricate both sides of the running belt. After the lubrication is completed, start the machine at 1km/h to let the running belt bring silicon all over the board.
Align and tighten the treadmill belt
- ALIGN THE BELT: Due to its use, the belt can move off-center. If the belt has moved to the left, start the treadmill and increase the speed to 3 MPH. Use the 5mm Wrench to turn the fixed left bolt clockwise or turn the fixed right bolt counterclockwise. Don’t tighten the belt too much in order to be able to walk.
Repeat this procedure until the belt is properly aligned.
- TIGHTEN THE BELT: (if the belt slips on the treadmill when walking). Start treadmill and increase the speed to 3 MPH. Using the 5mm wrench, turn both bolts 1/4 clockwise. If the belt is properly tight to walk, you must be able to pull up each side of the belt 5 or 7 cm off the platform. Be careful and maintain the belt aligned. Repeat this procedure until the belt is properly tightened.
• TIGHTEN THE DRIVE BELT:
If the drive belt becomes loose after using it for a period of time, you need to:
(1) Open the motor cover.
(2) Use the 5mm wrench to turn the adjusting bolt clockwise.
Repeat this procedure until the drive belt is not slippery anymore.
- CLEANING: Don’t use abrasive products, a damp cloth is enough.
- LEVELING: If your unit is provided with leveling wheels, please adjust them in order to avoid vibrations and therefore malfunctions.
- KEEP THESE MAINTENANCE ADVISES FOR FUTURE REFERENCES
CURSOR CARE
This electronic product must not be disposed of in municipal waste. To preserve the environment, this product must be recycled after its useful life as required by law.
Contact Cursor 7/24 response
√ 7*24 online California-based customer service team to solve after-sales problems without obstacles
√ Return Policy: 30-Day Hassle-Free Return and Exchange
√ Customer Service: California-Based Service Team Providing personalized solutions to ensure 100% customer satisfaction
√ Exclusive Maintenance Service: We honor our commitment to quality and durability by offering free maintenance tools for orders within 6 months, including lubricants and remote control
Contact Number：866-950-8629
CursorCare Team E-Mail：cursorcare@outlook.com
You must preserve the original packaging with its protections, purchase receipt, manual and components during the guarantee period.
Documents / Resources
 | CURSOR FITNESS C20 Under Desk Treadmill 2 in 1 Walking Pad [pdf] User Manual C20 Under Desk Treadmill 2 in 1 Walking Pad, C20, Under Desk Treadmill 2 in 1 Walking Pad, Treadmill 2 in 1 Walking Pad, 2 in 1 Walking Pad, Walking Pad |
