CTA - logoPAD-SHFSW
CTA DIGITAL Heavy-Duty Medical Mobile Floor Stand (White)
for 7-13 Inch Tablets
INSTRUCTION MANUALCTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand - pig 1Thank you for choosing CTA Digital’s product. We hope that you will enjoy using it. Please follow the guidelines and instructions as laid out in this instruction manual.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand - pig 2

Package Contents:

CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Package Contents

Instructions:

  1. Unlock the Security HolderCTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Unlock the Security Holder
  2. Going the Cable Through the Cable Routings on the Pole
    This product allows you to go through the cable from the cable routings on the pole and gooseneck.

CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Going the Cable Through the Cable Routings on the Pole 1

  1.  Put the top pole to the lowest position, insert the cable into the cable routing on the bottom pole and push inward.
    CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Going the Cable Through the Cable Routings on the Pole 2
  2. Draw out the top pole and continue to push inward the cable until the cable head is visible through the cable routing on the top pole.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Going the Cable Through the Cable Routings on the Pole 3
  3. Draw out the cable head from the cable routing on the top pole.This product allows you to go through the cable on the top of the gooseneck.

Stand Assembly:CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Stand Assembly

  1. Insert the pole into the center of the heavy-duty base.
  2. Place metal washer over-tightening screw rod, then screw into the bottom side of the stand base center, turning clockwise to tighten.

Attaching wheels:
Connect wheels to stand base before attaching pole.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand - Attaching wheels Screw wheels into floor base by hand, then use a wrench to tighten.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand - Attaching wheels 2

Connecting the Gooseneck Tablet Holder

  1. Place the gooseneck over the metal connection on the pole

    CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand - Connecting the Gooseneck Tablet Holder

  2. Turn clockwise to screw down until tight.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand - Connecting the Gooseneck Tablet Holder 2
  3. Use the smaller Allen key to tighten the small meter screw inside the gooseneck.
    Note: if the metering screw is already in, unscrew before attaching the gooseneck in step 2.

Installing your Device and Adjusting the Tablet Holder

  1. Press and hold on to the release button to unlock the holder, place tablet against corner then slide in until snug.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Installing your Device and Adjusting the Tablet Holder
  2. Use the Allen key to adjust the tension at the point of connection between the tablet holder and gooseneck, flex the gooseneck to adjust the view angle according to your needs.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Unlock the Security Holder 2
  3. Rotate plastic grip counterclockwise to loosen, then adjust the pole to the desired height. Rotate plastic grip clockwise to tighten.CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand -Unlock the Security Holder 3

[email protected]

Documents / Resources

CTA Digital PAD-SHFS Heavy-Duty Medical Mobile Floor Stand [pdf] Instruction Manual
PAD-SHFS, Heavy-Duty Medical Mobile Floor Stand, Medical Mobile Floor Stand, Mobile Floor Stand, Floor Stand, Mobile Stand

Leave a comment

Your email address will not be published.