Funsicle Oval Oasis Designer Above Ground Swimming Pool

1. Úvod

Thank you for choosing the Funsicle Oval Oasis Designer Above Ground Swimming Pool. This manual provides essential information for the safe assembly, operation, and maintenance of your pool. Please read all instructions carefully before setup and retain this manual for future reference.

The Funsicle Oval Oasis Designer pool measures 13'11" x 8'2" x 39.5" (167"L x 98"W x 39.5"H) and features a sophisticated dark herringbone exterior print with a honeycomb interior. It is designed for durability and ease of use, providing a refreshing experience for up to 6 to 7 people.

2. Bezpečnostní informace

VAROVÁNÍ: Nedodržení těchto varování může mít za následek vážné zranění nebo smrt.

• Dohled dospělé osoby je vyžadován po celou dobu, kdy se děti nacházejí v bazénu nebo v jeho blízkosti.
• Neskákejte ani se nepotápějte do bazénu. Hloubka vody není pro potápění dostatečná.
• Keep children away from the pool when not in use. Secure the ladder or remove it to prevent unsupervised access.
• Ensure the pool is set up on firm, level ground, free from sharp objects.
• Udržujte správné chemické složení vody, abyste předešli nemocem přenášeným vodou.
• Udržujte elektrické kabely a spotřebiče mimo oblast bazénu.
• Check and comply with local building codes and ordinances regarding pool installation.

3. Obsah balení

Před zahájením montáže ověřte, zda jsou všechny komponenty přítomny:

• Oval Oasis Pool Liner (Durable 3-ply ToughMesh)
• SmartConnect Frame (Ultra-strong oval poles with matte finish)
• FiltraBoost 800S Pool Pump with AutoSkimmer (110-120V)
• Filtrační vložka typu D
• Žebřík SureStep
• Opravná záplata
• Uživatelská příručka / Návod k obsluze

4. Pokyny k nastavení

For a visual guide, please refer to the official Funsicle Oasis Pool Tutorial video below.

4.1. Příprava místa

• Choose a flat, firm, and level surface. Use a spirit level to confirm the ground is perfectly flat.
• Clear the area of any stones, sharp objects, or debris that could puncture the pool liner.
• If using a filtration system, position the pool 10-21 feet away from the power outlet for the pump.

Obraz: Site preparation. Ensure the ground is firm, flat, and clear of any sharp objects before laying out the pool liner.

4.2. Montáž bazénu

• Lay out the ground cloth (if purchased) in the prepared area.
• Unfold the pool liner over the ground cloth, ensuring it is as flat as possible. Allow it to warm in the sun for approximately two hours to make it more pliable.
• Lay out all frame components around the liner.
• Assemble the horizontal beams by inserting them into the T-fittings. Ensure the pins snap securely into place.
• Thread the assembled horizontal beams through the top liner sleeves.
• Insert the foot pads onto the vertical legs.
• Carefully slide the vertical legs through the liner belt loops and snap them into the T-fittings. Ensure the legs are perpendicular to the ground.
• Perform a final check to ensure all frame pins are securely snapped and the structure is stable.

Obraz: Assembled Funsicle Oval Oasis Designer Pool. The image displays the pool's exterior design and the sturdy frame structure.

Obraz: Durable Liner Construction. This diagram illustrates the 3-layered ToughMesh material of the pool liner, consisting of polyester mesh between heavy gauge PVC layers for puncture resistance.

4.3. Naplnění bazénu

• Fill the pool with approximately one inch of water.
• Stop the water flow and carefully smooth out any wrinkles on the pool floor by walking around the inside of the pool. Ensure the liner is taut all around.
• Continue filling the pool to the recommended level, typically 6 inches below the top rim. Do not overfill.

4.4. Filtration System Installation

This pool includes a FiltraBoost 800S Pool Pump with AutoSkimmer. Follow these steps for installation:

• Locate the inlet and outlet holes on your pool liner.
• Insert the suction fittings (for skimmer) and return fittings (for water return) through the designated holes from the inside of the pool.
• From the outside, disassemble the skimmer seal ring and re-thread it onto the skimmer through the wall opening, tightening securely.
• Disassemble the return fitting assembly from the inside of the pool. Insert the fitting with the fitting gasket from the inside. On the outside, place the thrust washer on the fitting, followed by the fitting nut. Hand-tighten the fitting nut.
• Nainstalujte hadici třamp on each end of the provided hose.
• Attach one end of the hose to the skimmer and the other end to the return fitting. Slide the hose end over the O-ring on the fittings and tighten the hose clamps directly over the O-rings.
• Plug the pump into a grounded GFCI outlet. If the pump does not turn on immediately, press the 'Reset' button on the GFCI plug. Refer to the pump's user guide for timer settings.

Obraz: SkimmerPlus Filter Pump Diagram. This image shows the internal components and how the skimmer basket picks up debris while the filter cartridge captures small particles.

Obraz: JetMaxx Aeration Feature. A close-up view of the JetMaxx aeration feature, which helps improve water circulation and quality.

5. Návod k obsluze

• Provoz čerpadla: The FiltraBoost pump should run daily to ensure proper water circulation and filtration. Refer to the pump's user guide for recommended operating times and timer settings.
• Hladina vody: Maintain the water level between the minimum and maximum fill lines indicated on the skimmer.
• Použití žebříku: Always use the SureStep ladder for safe entry and exit. Ensure it is securely placed before use.

6. Údržba

6.1. Chemie vody

• Regularly test your pool water using a test kit to ensure pH and chlorine levels are within a healthy range.
• Adjust chemicals as needed to maintain optimal water balance.

6.2. Čištění

• Empty the AutoSkimmer basket daily to remove leaves and large debris.
• Rinse the Type D filter cartridge with a garden hose every few days, or more frequently depending on usage. Replace the cartridge every 2-4 weeks or when visibly dirty.
• Pravidelně kartáčujte stěny a dno bazénu, abyste zabránili hromadění řas.
• Dno bazénu v případě potřeby vysávejte, abyste odstranili usazené nečistoty.

6.3. Příprava na zimu

While some users may choose to leave the pool assembled during winter, it is generally recommended to drain, disassemble, clean, and store the pool in a dry, protected area to prolong its lifespan. Follow the detailed winterization instructions in your pump's user guide.

7. Řešení problémů

• Čerpadlo neběží: Check the GFCI plug for a tripped circuit. Press the 'Reset' button. Ensure the power cord is securely plugged in. Verify the timer settings.
• Poor Water Circulation: Check if the filter cartridge is clean and not clogged. Ensure hoses are properly connected and free of kinks. Verify water level is adequate.
• Zakalená voda: Test water chemistry and adjust as necessary. Ensure the pump is running for sufficient periods. Clean or replace the filter cartridge.
• Únik: Inspect the liner for punctures and use the provided repair patch if a small hole is found. Check all hose connections and fittings for tightness.

8. Specifikace

9. Záruka a podpora

For warranty information, product support, or to purchase replacement parts, please contact Funsicle customer service:

• Webmísto: funsicle.com/support
• Telefon: 888-670-4FUN (888-670-4386)
• E-mail: HelloFun@Funsicle.com