CREALITY ZDTP-32 Bit BLTouch V3.1 Auto Bed Leveling Sensor Kit

AUTO BED LEVELING SENSOR FOR 3D PRINTER
This guidebook is for Creality V1 mainboard.lt include but not limited to the following 3d printer: CR-10/Ender-3
File download: https://www.creality.com/download/

Scan QR code to view detailed instruction

SHENZHEN CREALITY 3D TECHNOLOGY CO.,L TD.
11F & Room 1201,Block 3,JinChengYuan,Tongsheng Community, Dalang, Longhua District, Shenzhen, China,518109
Official Website: www.creality.com
Tel: +86 755-8523 4565
E-mail: info@creality.com cs@creality.com

Packing List

Circuit Principle

Update Firmware

1. Connect ISP Pinboard and Burner.
2. Open the control box and fmd out the mainboard
3. Insert ISP pinboard into the mainboard 2X3 pins as the sign shows.
4. Insert the burner into computer USB port.

1. Open progisp.exe
2. Select Chip ATmega1284p3, Click … —> Set Low Value=D6, HighValue=DC, ExtValue=FD—>Click Write and close the window.
3. load Flash—>Select .hex 1ile.
4. Click Auto to update firmware, wait until it 1inishs, then close.
5. Unplug the ISP Pinboard from mainboard.

Update Firmware

1. Double-click to open computer-right-click to format SD card.
2. Copy the firmware to the SD card. Note: the SD card only holds one firmware file.
3. Insert SD card.
4. Insert the power cord and press the switch.
5. Wait for the brush firmware to complete (about 10 seconds).

Install BL Touch

1. Insert connectors into 5 Pin Port.
2. Install BL Tocuh on the rack with 2 M3X6 screws
3. Loosen all fan cover screws, Install the farme on the corresponding position with 2 M3X8 screws
4. Secure the cable to the guide tube and cable with a cable tie and bypass the rear side of the gantry.

1. Unplug the screen cable, connect the pinboard A to the screen port (EXP1).
2. Insert the screen cable into 10 pins port.
3. insert the connectors to the 3 pins port as the sign shows.
4. Unplug the Z limit switch(Z-stop port),and insert the connectors

1. Unplug the screen cable, connect the pinboard A to the screen port (EXP1).
2. Insert the screen cable into 10 pins port.
3. insert the connectors to the 3 pins port as the sign shows.
4. Unplug the Z limit switch(Z-stop port),and insert the connectors.

Platform Adjustment

1. Prepare—>Auto home, and wait until it stops.
2. Prepare->Move axis—>Move Z—>Move 0.1 mm—>Rotate the knob until the distance between them is about 0.2mm (as a sheet of A4 paper) , write down the value of A.
3. Rotate the knob until the distance between them is about 0.2mm (as a sheet of A4 paper) , write down the value of A (For example, figure 3)
4. Control—>Motion—>Z Offset—>write down the value of B, then rotate the knob until it comes out as: C=B+A. Return Control and Select Store settings.

Platform Adjustment

1. Prepare—>Auto home, and wait until it stops.
2. Select control.
3. Select Bed leveling.
4. Select Level Bed.
5. leveling 9 points
6. 9 points leveling completed
7. automatic leveling is completed, the machine is ready to be OK

Note: Every machine has its own operation interface.

Software Settings

AUTO BED LEVELING SENSOR FOR 3D PRINTER

This guidebook is for Creality V2 mainboard.It include but not limited to the following 3d printer: CR-10S/CR-10 S4/CR-10 S5/CR20.
File download: https://www.creality3d.cn/download/
Video instruction of firmware flash: http://bit.ly/2FkyOag
Video insruction of USB Driver Installation: http://bit.ly/2ZNvjTn

Scan QR code to view detailed instruction

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.

12/F, Block 3, JinChengYuan, Huafan Road, Tongsheng Community, Dalang, Longhua District, Shenzhen, China, 518109
Official Website: www.creality3d.cn
Tel: +86 755-2103 4006
E-mail: info@creality3d.cn cs@creality3d.cn

Packing List

Install BLTouch

Circuit Wiring

1. Open the control box and find out the mainboard.
2. Unplug the Z limit switch (Z port),and insert the connectors.
3. Insert connectors into the mainboard D11 pins as the colorshows.
4. Closed the control box.
5. Connect ISP Pinboard and Burner.
6. Connect computer to update firmware with usb cable.

Update Firmware

Open Cura→Machine→Machine settings→Select Serial port （COM）& Baudrate（115200）

Machine→Install custom firmware→Select .hex file→Click OK to update，Waiting until it is finished, then click ok.

Platform Adjustment

1. Prepare→Auto home，and wait until it stops.
2. Prepare→Move axis→Move Z→Move 0.1mm→Rotate the knob until the distance between them is about 0.2mm（as a sheet of A4 paper），write down the value of A.
3. Rotate the knob until the distance between them is about 0.2mm（as a sheet of A4 paper），write down the value of A（For example, figure 3）.
4. Control→Motion→Z Offset→write down the value of B，then rotate the knob until it comes out as: C=B+A. Return Control and Select Store settings.

Software Settings

Documents / Resources

CREALITY ZDTP-32 Bit BLTouch V3.1 Auto Bed Leveling Sensor Kit [pdf] User Guide ZDTP-32 Bit, BLTouch V3.1 Auto Bed Leveling Sensor Kit, Auto Bed Leveling Sensor, Bed Leveling Sensor, ZDTP-32 Bit, Leveling Sensor

References

• User Manual