COSTWAY-LOGO

COSTWAY ES10056US 52-Inch Ceiling Fan Lamp with Beads

COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads

Before You Start

  • Please read all instructions carefully.
  • Retain instructions for future reference.
  • Separate and count all parts and hardware.
  • Read through each step carefully and follow the proper order.
  • We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
  • Always place the product on a flat, steady, and stable surface.
  • Keep all small parts and packaging materials for this product away from

babies and children as they potentially pose a serious choking hazard.

SAFETY INFORMATION

  1. To reduce the risk of electric shock, the electricity has been turned off at the circuit breaker or fuse box before beginning.
  2. All wiring must be in accordance with the National Electrical Code NASI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
  3. The outlet box and support structure must be securely mounted and capable of reliably supporting 35Ib.(15.9kg).Use only UL-listed outlet boxes marked “Acceptable for Fan Support of 35Ibs(15.9kg}or less.”
  4. The fan must be mounted with a minimum of 7 ft (2m) clearance from the trailing edge of the blades to the floor.
  5. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
  6. Do not place objects in the path of the blades.
  7. To avoid personal injury or damage to the fan and other items, please be careful when working around or cleaning the fan.
  8. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
  9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
  10. All setscrews must be checked and retightened where necessary before installation.

WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
WARNING: To reduce the risk or fire or electric shock.do not use this fan with any solid-state speed control device.
WARNING: To avoid possible electric shock,
turn the electricity off at the main fuse box before wiring.If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to the outlet box marked’ Acceptable for fan support of 35 lbs.(15.9 kg)or less and use the screws provided with the outlet box.

SPECIFICATION

Size Speed Volts Amps Watts RPM CFM       Net             Gross

Weihgt Weight

   
  Low   0.21 10 67 670

20.0lb       26.2Ib

   
52in Medium 120 0.35 27 119 2975       9.1kg      11.9kg    
  High   0.48 71 174 5520    

The above data are for reference only, Actually, the motor speed of each ceiling fan is a little different. Any products, Subject to actual products as standard.

NOTE: These are approximate measures.They do not include the amps and wattage used by the light kit.

Specifications & measurements shown are subject to± 5% variations.

TOOLS REQUIREDCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-1

HARDWARE INCLUDED

COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-2

PACKAGE CONTENTSCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-3

WOODEN CEILINGCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-4

For a wooden ceiling, use the wood screw to drill on the wooden beam or the “junction box” to fix the hanging bracket (selection is made according to the actual requirements of the customers).

STEP 1A-WOODEN CEILING

SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

  1. Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Self Tapping Screws (B) will be drilled.
  2. Remove the Mounting Bracket (A), drill 4 holes for 3MM diameter, and install the mounting bracket onto the wooden ceiling with the 4 Self Tapping Screws (B) & Washers (C).

IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG

CONCRETE CEILINGCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-5

Note: According to the ceiling of different materials, use different screws to fix the hanging bracket. Don’t fix the hanging bracket on the wood ceiling less than 12MM to prevent danger caused by loosening of screws. After the hanging bracket is completed, ensure that it can withstand the tension test of more than 150 LBS/68KG for safety.

For the concrete ceiling, use the percussion bit with a diameter 8mm to drill holes according to the length of the expansion screws. Then use the attached expansion screws to fix the hanging bracket onto
the ceiling (selection is made according to actual requirements of the customers).

STEP 2A-CONCRETE CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

  1. Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Expansion Bolts (B) will be drilled
  2. Remove the Mounting Bracket (A), drill 4 holes and insert 4 Expansion Bolts (B) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (C), Spring Washers (D) and Nuts (E).

IMPORTANT: SCREWS & NUTS MUST BE TIGHTENED TILL SNUG

INSTALL THE HANGING PART OF THE CEILING FAN.

INSTALL DOWNROD ASSEMBLYCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-6COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-7

  1. Thread the suspender through the suspended clock and coupling cover.
  2. Then insert the tail of the suspender from the lifting head of the motor.
  3. After the lateral pin is threaded out from the suspended head position, insert R type pin.
  4. Tighten the lifting head screws.
  5. Hang the fan of the hanging pipe into the hanger.

Assembly – Hanging the Fan

Making the electrical connections 

COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-8

  • a. The motor while wiring to the while “to motor N” wire from Receiver with a wire nut.
  • b. The motor black wire to the black” to motor L” wire from Receiver with a wire nut.
  • c. The lamp blue wire to the blue” to Light” wire from the Receiver with a wire nut.
  • d. The white wire from the Outlet Box to the red”AC in N” wire from the Receiver with a wire nut.
  • e. The black wire from the Outlet Box to the red”AC in L” wire from the Receiver with a wire nut. Connect the supply ground wire to the green ground wire from the canopy and the green ground wire from the hanger bracket together using a wire nut.
    Tuck all wire nuts and wires carefully up into the Outlet Box.EXCEPT for the antenna. which should remain outside Outlet Box

Preparing for mountingCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-9

  1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
  2. Push the canopy ring to the bottom of the canopy, slide the inner holes aligned lo the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-10

ASSEMBLY ATTACHING  THE FAN BLADES

 Attaching the blades to the arms COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-11

  1. Pass the red washer through the screw.
  2. Tighten the screw through the blade and tighten it on the arms. 3 Repeat the above steps to tighten the four sets of blades.

Fastening the blade arms to the motor

  • WARNING: Remove the rubber motor stops on the bottom ill of the fan before installing the blades or testing the motor.
  • NOTE: Your fan features revolutionary advancements for quick and easy blade installation.Including an alignment post and captive blade arm screws.
  • NOTE: Your fan blades are reversible. Select the blade side finish which best accentuates your decor.COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-12
  1. Fasten the arm to the fan-motor assembly by inserting the alignment post in the slot on the bottom of the motor and tightening the pre­installed arm screws.
  2. Repeat this step for the remaining blade assemblies.

ASSEMBLY ATTACHING THE LAMP

Connecting lamp wire COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-13

CAUTION: To reduce the risk of electric shock, disconnect the electrical circuit to the fan before installing the light fixture.

  1. insert the ”white” line in the switching box of the motor into the ”white” line of the light and tie insulated rubber tape.
  2. insert the “blue” line in the switching box of the motor into the “blue” line of the light and tie insulated rubber tape.

Tightening_the_screw of the box cover.COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-14

  1. Take the wire into the switching box of the motor.
  2. Align the opening of the switching box of the light at the switch locking position of the forward and reverse rotation of the motors switching box. Place the cover. Screw in the screw of the switching box.

installing the crystal shade & bulbCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-15

  • WARNING: Allow the shatter-resistant bowl to cool completely before removing.
  • CAUTION: Make sure the power is off before attaching or removing the shatter-resistant bowl.
  • CAUTION: Do not over tighten the hex nut, overtightening the hex nut may cause the shatter-resistant bov.1 to break.

OPERATIONCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-16

OPERATING YOUR FAN
The appropriate speed settings for warm or cool weather depend on factors such as the room size, ceiling height, and the number of fans.
The slide switch (XX) controls the direction of the blades: forward (switch down) or reverse (switch up).

NOTE: Wait for the fan to slop before reversing the direction of the blade rotation

  • A. Warm weather-(Forward) A downward airflow creates a cooling effect.
    This allows you to set your air conditioner on a higher setting without affecting your comfort.
  • B. Cool weather-(Reverse) An upward airflow moves warm air off the ceiling. This allows you to set the heating unit on a lower setting without affecting your comfort.

CARE AND CLEANING

D Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.

  • Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electric shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
  • You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
  • You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

TROUBLESHOOTING

Problem Solution
 

 

 

 

 

 

 

 

The fan will not start.

□    Check the main and branch circuit fuses or breakers.

□    Check the line wire connections to the fan and switch wire connections in the switch housing.

□    Ensureallmotor housing screws are snug.

□    Ensure the screws that attach the fan blade bracket to the motor hub are tight.

□    Ensure the wire nut connections are not ratting against each other or the interior wall of the switch housing.

□     Allow a 24-hour “breaking in”period. Most noises associated with a new fan disappear over this time.

□    If you are using the light kit, ensure the screws securing the glassware are tight.

Check Iha! the light bulbs are also secure.

□    Ensure the canopy is a short distance from the ceiling.It should not touch the ceiling.

□    Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

 

 

The fan wobbles.

D Check that all blades and blade arm screws are secure.

D Most fan wobble problems are caused when blade levels are unequal.

D Check this level by selecting a point on the ceiling above the tip of the blades.

D Measure from a point on the center of each blade to the point on the ceiling. Measure this distance. D Rotate the fan until the next blade is positioned for measurement.

D Repeat for each blade. Any measurement deviation should be within 1/8 in.

D Run the fan for ten minutes. If the fan continues to wobble please contact Customer Service.

Installation tutorialCOSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-17

  1. Use the specified tool to unlock the bottom decoration of the lamp
  2. Select the appropriate bulb and install it on the lamp holder
  3. Install the glass to the designated position
  4. install the unlocked decorative parts back to the original position

Use of remote control

COSTWAY-ES10056US-52-Inch Ceiling-Fan-Lamp-with-Beads-FIG-18

Welcome to visit our website and purchase our quality products!
With your inspiring rating, COSTWAY will be more consistent to offer you
EASY SHOPPING EXPERIENCE, GOOD PRODUCTS, and EFFICIENT SERVICE!

  • US office: Fontana, California
  • UK office: Ipswich
  • Reward Points
  • Exclusive Customer Service
  • Personalized Recommendations
  • Permanent Shopping Cart
  • Order History

We would like to extend our heartfelt thanks to all of our customers for taking the time to assemble this product and giving us valuable feedback.

Documents / Resources

COSTWAY ES10056US 52-Inch Ceiling Fan Lamp with Beads [pdf] User Manual
ES10056US, 52-Inch Ceiling Fan Lamp with Beads

Leave a comment

Your email address will not be published. Required fields are marked *