Coolblue 323CQR ARTYMIS Series LCD Monitor User Guide

323CQR ARTYMIS Series LCD Monitor
MPG ARTYMIS 323CQR (3DB1)
MAG ARTYMIS 324CP (3DB3)
User Guide

Getting Started

This chapter provides you with information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.

Package Contents

Monitor	MPG ARTYMIS 323CQR MAG ARTYMIS 324CP
Documentation	Quick Start Guide
	Registration Card
Accessories	Stand with Screw(s)
	Stand Base with Screw(s)
	Stand Cover
	Screw(s) for Wall Mount Bracket
	Power Cord
	Mouse Bungee (Optional)
Cables	HDMI Cable
	DisplayPort Cable
	Type C Cable (Optional)
	USB Upstream Cable (for USB Type-B Upstream Port)

Important

• Contact your place of purchase or local distributor if any of the items are damaged or missing.
• Package contents may vary by country.
• The included power cord is exclusively for this monitor and should not be used with other products.

Installing the Monitor Stand

1. Leave the monitor in its protective foam packaging. Align the latches of the stand to the monitor. Tighten the stand with screws.
2. Connect the stand base to the stand and tighten the screw to secure the stand base.
3. Align the latches to place the stand cover.
4. Adjust the angle of the stand, and make sure the stand assembly is properly installed before setting the monitor upright.

Important

• Remove the screws on the monitor groove if needed before installing the stand.
• Place the monitor on a soft, protected surface to avoid scratching the display panel.
• Do not use any sharp objects on the panel.
• The groove for installing the stand bracket can also be used for the wall mount. Please contact your dealer for a proper wall mount kit.

Adjusting the Monitor
This monitor is designed to maximize your viewing comfort with its adjustment capabilities.
Important
Avoid touching the display panel when adjusting the monitor.

Monitor Overview

1. Light Sensor (MPG ARTYMIS 323CQR)	9. Power Jack
2. Microphone (MPG ARTYMIS 323CQR)	10. DisplayPort
3. Headset Hanger	11. HDMI Port
4. Macro Key To activate the Gaming OSD Application.	12. USB Type-C Port This port supports DisplayPort Alternate (DP Alt) Mode and up to 5V/3A power delivery.
5. Navi Key	13. Headphone Jack
6. Power Button	14. USB 2.0 Type B Upstream Port For USB Upstream Cable. Important Check the package for USB Upstream Cable and connect it to the PC and monitor. Once this cable is connected, to the USB Type A Downstream Ports on the monitor will be ready for use.
7. Cable Routing Hole	15. USB 2.0 Type-A Port
8. Kensington Lock

Connecting the Monitor to PC

1. Turn off your computer.
2. Connect the video cable from the monitor to your computer.
3. Connect the power cord to the monitor power jack. (Figure A)
4. Plug the power cord into the electrical outlet. (Figure B)
5. Turn on the monitor. (Figure C)
6. Power on the computer and the monitor will auto-detect the signal source.

OSD Setup

This chapter provides you with essential information on OSD Setup.
Important
All information is subject to change without prior notice.
Navi Key
The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu.

Up/Down/Left/Right:

• selecting function menus and items
• adjusting function values
• entering into/exiting from function menus

Press (OK):

• launching the On-Screen Display (OSD)
• entering submenus
• confirming a selection or setting

Hot Key

• Users may enter into preset function menus by moving the Navi Key up, down, left or right when the OSD menu is inactive.
• Users may customize their own Hot Keys to enter into different function menus.

OSD Menus

  Important
When receiving HDR signals, Night Vision, MPRT, Low Blue Light, HDCR, Brightness, Contrast, Color Temperature, Auto Brightness Control, and Ambient RGB Light will be grayed out.
G.I. (MPG ARTYMIS 323CQR)

1st Level Menu	2nd Level Menu	Description
Auto Brightness Control	OFF	• Through the internal Light Sensor and AI (Artificial Intelligence) algorithm, this function detects the ambient light and automatically sets the monitor to optimal brightness for users. • When Auto Brightness Control is set to Auto or Customize, the brightness of OSD will be grayed out. • Customize allows users to adjust the auto-brightness curve. • HDCR and MPRT will be set to OFF while Auto or Customize is selected.
	Auto
	Customize
Ambient RGB Light	OFF	• Through the internal RGB Sensor and AI algorithm, this function detects the ambient color temperature and presents the best light effects synced to the environment. • The Color Temperature of OSD will be grayed out while this function is enabled.
	ON
Sound Tune	OFF	• Through the internal digital array microphone and AI algorithm, this function enables Active Noise Cancellation (ANC) technology. • For Sound Tune to properly work, the computer needs to be connected to the USB Upstream port of the monitor.
	ON
KVM	Auto	• Auto allows the monitor to automatically switch between USB input sources, such as keyboards, mice, or other USB devices. • Users can also designate an Upstream port or USB Type-C as the only USB signal source.
	Upstream
	Type-C

Smart Crosshair	Icon	None	• Through the AI algorithm, this function enhances the visibility of the in-game crosshair. • Users can select the color and position of the crosshair.
	Color	White
		Red
		Auto
	Position
	Reset

Gaming

1st Level Menu	2nd/3rd Level Menu	Description
Game Mode	User	• Use the Up or Down Button to select and preview mode effects. • Press the OK button to confirm and apply your mode type.
	FPS
	Racing
	RTS
	RPG
Night Vision	OFF	• This function optimizes background brightness and is recommended for FPS games.
	Normal
	Strong
	Strongest
	A.I.
Response Time	Normal	• Users can adjust Response Time in any mode. • Response Time will be grayed out while MPRT is enabled.
	Fast
	Fastest

1st Level Menu	2nd/3rd Level Menu		Description
MPRT	OFF		• When MPRT is enabled, Brightness cannot be enabled and will be grayed out. • Response time will be grayed out while MPRT is enabled. • MPRT is available when the refresh rate is over 85Hz.
	ON
Refresh Rate	Location	Left Top	• Location is adjustable in OSD Menu. Press the OK button to confirm and apply your Refresh Rate Location. • This monitor follows and works at the Operating System’s preset Screen Refresh Rate.
		Right Top
		Left Bottom
		Right Bottom
		Customize
	OFF
	ON
Alarm Clock	Location	Left Top	• After setting the time, press the OK button to activate the timer. • Users can select their own location.
		Right Top
		Left Bottom
		Right Bottom
		Customize
	OFF
	15:00	00:01 ~ 99:59
	30:00
	45:00
	60:00

1st Level Menu	2nd/3rd Level Menu		Description
KVM (MAG ARTYMIS 324CP)	Auto		• Auto allows the monitor to automatically switch between USB input sources, such as keyboards, mice, or other USB devices. • Users can also designate an Upstream port or USB Type-C as the only USB signal source.
	Upstream
	Type-C
Smart Crosshair (MAG ARTYMIS 324CP)	Icon	None	• Through the AI algorithm, this function enhances the visibility of the in-game crosshair. • Users can select the color and position of the crosshair.
	Color	White
		Red
		Auto
	Position
	Reset
FreeSync Premium	OFF		• FreeSync Premium prevents screen tearing. • MPRT will be disabled if FreeSync Premium is enabled.
	ON

Professional

1st Level Menu	2nd Level Menu	Description
Pro Mode	User	• Use the Up or Down Button to select and preview mode effects. • Press the OK button to confirm and apply your mode type.
	Anti-Blue
	Movie
	Office
	sRGB
	ECO
Low Blue Light	OFF	• Low Blue Light protects your eyes against blue light. When enabled, Low Blue Light adjusts the screen color temperature to a more yellow glow. • When Pro Mode is set to Anti-Blue, it is mandatory to enable Low Blue Light.
	ON
HDCR	OFF	• HDCR enhances image quality by increasing the contrast of images. • When HDCR is set to ON, Brightness will be grayed out. • HDCR and MPRT cannot be enabled simultaneously.
	ON
MPRT	OFF	• When MPRT is enabled, Brightness cannot be enabled and will be grayed out. • Response time will be grayed out while MPRT is enabled. • MPRT is available when the refresh rate is over 85Hz.
	ON
Image Enhancement	OFF	• Image Enhancement enhances image edges to improve their acutance.
	Weak
	Medium
	Strong
	Strongest

Image

1st Level Menu	2nd/3rd Level Menu		Description
Brightness	0-100		• Properly adjust Brightness according to the surrounding lighting. • Brightness will be grayed out when MPRT or HDCR are enabled.
Contrast	0-100		• Properly adjust Contrast to relax your eyes.
Sharpness	0-5		• Sharpness improves the clarity and details of images.
Color Temperature	Cool		• Use the Up or Down Button to select and preview mode effects. • Press the OK button to confirm and apply your mode type. • Users can adjust Color Temperature in Customization mode.
	Normal
	Warm
	Customization	R (0-100)
		G (0-100)
		B (0-100)
Screen Size	Auto		• Users can adjust Screen Size in any mode, any resolution, and any screen refresh rate.
	4:3
	16:9

Input Source

1st Level Menu	2nd Level Menu	Description
HDMI1		• Users can adjust Input Source in any mode.
HDMI2
DP
Type-C
Auto Scan	OFF	• Users can use the Navi Key to select Input Source at the below status: • While “Auto Scan” is set to “OFF” with the monitor at power saving mode; • While the “No Signal” message box is shown on the monitor.
	ON

Navi Key

1st Level Menu	2nd Level Menu	Description
Up / Down / Left / Right	OFF	• All Navi Key items can be adjusted via OSD Menus.
	Brightness
	Game Mode
	Smart Crosshair
	Alarm Clock
	Input Source
	Refresh Rate
	Info. On-Screen
	Night Vision
	KVM

Setting

1st Level Menu	2nd Level Menu	Description
Language	繁體中文	• Users have to press the OK button to confirm and apply the Language setting. • Language is an independent setting. Users’ own language settings will override the factory default. When users set Reset to Yes, the Language will not be changed.
	English
	Français
	Deutsch
	Italiano
	Español
	한국어
	日本語
	Русский
	Português
	简体中文
	Bahasa Indonesia
	Türkçe
	(More languages coming soon)

1st Level Menu	2nd Level Menu	Description
Transparency	0~5	• Users can adjust Transparency in any mode.
OSD Time Out	5~30s	• Users can adjust OSD Time Out in any mode.
RGB LED (MPG ARTYMIS 323CQR)	OFF	• Users can adjust RGB LED to ON or OFF.
	ON
Power Button	OFF	• When set to OFF, users can press the power button to turn off the monitor.
	Standby	• When set to Standby, users can press the power button to turn off the panel and backlight.
Info. On-Screen	OFF	• The information on the monitor status will be shown on the right side of the screen. • Users can enable or disable the Info. On-Screen.
	ON
HDMI CEC	OFF	• HDMI CEC (Consumer Electronics Control) supports Sony PlayStation®, Nintendo® Switch™, Xbox Series X|S consoles, and various audio-visual devices that are CEC- capable. • If HDMI CEC is set to ON: • The monitor will automatically power on when the CEC device is turned on. • The CEC device will enter power-saving mode when the monitor is turned off. • When Sony PlayStation®, Nintendo® Switch™, or Xbox console is connected, Game and Pro Mode will be automatically set to User mode (Default) and can be adjusted to users’ preferred modes later.
	ON
Reset	YES	• Users can Reset and restore settings to the original OSD Default in any mode.
	NO

Specifications

Monitor	MPG ARTYMIS 323CQR	MAG ARTYMIS 324CP
Size	31.5 inch
Curvature	1000R
Panel Type	VA
Resolution	2560 x 1440 @165Hz	1920 x 1080 @165Hz
Aspect Ratio	16:9
Brightness (nits)	400	300
Contrast Ratio	2500:1	3000:1
Refresh Rate	165Hz
Response Time	4ms(GTG)
MPRT	1ms
I/O	• DisplayPort x 1 • HDMI Port x 2 • USB Type-C Port x 1 • USB 2.0 Type-A Port x 2 • USB 2.0 Type-B Upstream Port x 1 • Headphone Jack x 1
View Angles	178°(H), 178°(V)
DCI-P3*/ sRGB	89.8% / 113%	92.6% / 116.8%
Surface Treatment	Anti-glare
Display Colors	1.07B (8 bit +FRC)
Monitor Power Options	100~240Vac, 50/60Hz, 2A
Power Consumption (Typical)	Power On < 105W Standby < 0.5W Power Off < 0.3W

* Based on CIE1976 test standards.

Monitor		MPG ARTYMIS 323CQR	MAG ARTYMIS 324CP
Adjustment (Tilt)		-5° ~ 20°
Adjustment (Height)		0 ~ 100mm
Adjustment (Swivel)		-30° ~ 30°
Kensington Lock		Yes
VESA Mounting		• Plate Type: 100 x 100 mm • Screw Type: M4 x 10 mm • Thread Diameter: 4 mm • Thread Pitch: 0.7 mm • Thread Length: 10 mm
Dimension (W x H x D)		701.4 x 473.4 x 317.7 mm
Weight		9.0 Kg (Net) / 12.8 Kg (Gross)	8.7 Kg (Net) / 11.8 Kg (Gross)
Environment	Operating	• Temperature: 0℃ to 40℃ • Humidity: 20% to 90%, non-condensing • Altitude: 0 ~ 5000m
	Storage	• Temperature: -20℃ to 60℃ • Humidity: 10% to 90%, non-condensing

Preset Display Modes

MAG ARTYMIS 324CP

Standard	Resolution		HDMI	DP/ Type-C
VGA	640×480	@60Hz	V	V
		@67Hz	V	V
		@72Hz	V	V
		@75Hz	V	V
Dos-Mode	720×480	@60Hz	V	V
	720×576	@50Hz	V	V
SVGA	800×600	@56Hz	V	V
		@60Hz	V	V
		@72Hz	V	V
		@75Hz	V	V
XGA	1024×768	@60Hz	V	V
		@70Hz	V	V
		@75Hz	V	V
SXGA	1280×1024	@60Hz	V	V
		@75Hz	V	V
WXGA+	1440×900	@60Hz	V	V
WSXGA+	1680×1050	@60Hz	V	V
Full HD	1920×1080	@60Hz	V	V
		@120Hz	V	V
		@144Hz	V	V
		@165Hz	V	V
Video Timing Resolution	480P		V	V
	576P		V	V
	720P		V	V
	1080P		V	V
	1080P @120Hz		V	V

MPG ARTYMIS 323CQR

Standard	Resolution		HDMI	DP/ Type-C
VGA	640×480	@60Hz	V	V
		@67Hz	V	V
		@72Hz	V	V
		@75Hz	V	V
Dos-Mode	720×480	@60Hz	V	V
	720×576	@50Hz	V	V
SVGA	800×600	@56Hz	V	V
		@60Hz	V	V
		@72Hz	V	V
		@75Hz	V	V
XGA	1024×768	@60Hz	V	V
		@70Hz	V	V
		@75Hz	V	V
SXGA	1280×1024	@60Hz	V	V
		@75Hz	V	V
WXGA+	1440×900	@60Hz	V	V
WSXGA+	1680×1050	@60Hz	V	V
Full HD	1920×1080	@60Hz	V	V
		@120Hz	V	V
QHD	2560×1440	@60Hz	V	V
		@120Hz	V	V
		@144Hz	V	V
		@165Hz	X	V
Video Timing Resolution	480P		V	V
	576P		V	V
	720P		V	V
	1080P		V	V
	1080P @120Hz		V	V
	2160P @30Hz		V
	2160P @60Hz		V

Troubleshooting

The power LED is off.

• Press the monitor power button again.
• Check if the monitor power cable is properly connected.

No image.

• Check if the computer graphics card is properly installed.
• Check if the computer and monitor are connected to electrical outlets and are turned on.
• Check if the monitor signal cable is properly connected.
• The computer may be in Standby mode. Press any key to activate the monitor.

The screen image is not properly sized or centered.

• Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.

No Plug & Play.

• Check if the monitor power cable is properly connected.
• Check if the monitor signal cable is properly connected.
• Check if the computer and graphics card are Plug & Play compatible.

The icons, font, or screen are fuzzy, blurry, or have color problems.

• Avoid using any video extension cables.
• Adjust brightness and contrast.
• Adjust RGB color or tune the color temperature.
• Check if the monitor signal cable is properly connected.
• Check for bent pins on the signal cable connector.

The monitor starts flickering or shows waves.

• Change the refresh rate to match the capabilities of your monitor.
• Update your graphics card drivers.
• Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).

Safety Instructions

• Read the safety instructions carefully and thoroughly.
• All cautions and warnings on the device or User Guide should be noted.
• Refer servicing to qualified personnel only.

Power

• Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.
• If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.
• Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
• Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.
• Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
• If this device comes with an adapter, use only the MSI-provided AC adapter approved for use with this device.

Battery
Please take special precautions if this device comes with a battery.

• The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
• Avoid the disposal of a battery in a fire or a hot oven, or mechanically crushing or cutting of a battery, which can result in an explosion.
• Avoid leaving a battery in an extremely high temperature or extremely low air pressure environment that can result in an explosion or the leakage of flammable liquid or gas.
• Do not ingest the battery. If the coin/button cell battery is swallowed, it can cause severe internal burns and can lead to death. Keep new and used batteries away from children.

European Union:
Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with the local regulations.
Taiwan:
Please recycle used batteries
For better environmental protection, waste batteries should be collected separately for recycling or special disposal.
California, USA:
The button cell battery may contain perchlorate material and requires special handling when recycled or disposed of in California. For further information
please visit: https://dtsc.ca.gov/perchlorate/
Environment

• To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.
• Use this device only on a hard, flat, and steady surface.
• To prevent the device from tipping over, secure the device to a desk, wall, or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.
• To prevent fire or shock hazards, keep this device away from humidity and high temperature.
• Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.
• The maximum operating temperature is around 40℃.
• When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than an industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.
• ∙ Always keep strong magnetic or electrical objects away from the device.
• If any of the following situations arises, get the device checked by service personnel:
  • The power cord or plug is damaged.
  • Liquid has penetrated into the device.
  • The device has been exposed to moisture.
  • The device does not work well or you can not get it working according to the User Guide.
  • The device has dropped and been damaged.
  • The device has an obvious sign of breakage.

TÜV Rheinland Certification

TÜV Rheinland Low Blue Light Certification
Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light.

www.tuv.com

• Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.
• Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.
• Take breaks for 20 minutes every 2 hours.
• Look away from the screen and gaze at a distant object for at least 20 seconds during breaks.
• Make stretches to relieve body fatigue or pain during breaks.
• Use the Reader/Anti-Blue mode or turn on the optional Low Blue Light function.

TÜV Rheinland Flicker Free Certification

www.tuv.com

• TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flickers for the human eye and therefore strains the eyes of users.
• TÜV Rheinland has defined a catalog of tests, which sets out minimum standards at various frequency ranges. The test catalog is based on internationally applicable standards or standards common within the industry and exceeds these requirements.
• The product has been tested in the laboratory according to these criteria.
• The keyword “Flicker Free” confirms that the device has no visible and invisible flicker defined in this standard within the range of 0 – 3000 Hz under various brightness settings.
• The display will not support Flicker-Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by-products.)

Regulatory Notices

CE Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under the Directives of the Official Journal of the European Union.
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.

Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and an AC power cord, if any, must be used in order to comply with the emission limits.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

MSI Computer Corp.
901 Canada Court, City of Industry, CA 91748, USA
(626) 913-0828
www.msi.com

WEEE Statement
Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
Chemical Substances Information
In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information on chemical substances in products at: https://csr.msi.com/global/index
RoHS Statement
Japan JIS C 0950 Material Declaration
A Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006. https://csr.msi.com/global/Japan-JIS-C-0950-Material-Declarations
India RoHS
This product complies with the “India E-waste (Management and Handling) Rule 2011” and prohibits the use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Turkey EEE Regulation
Conforms to the EEE Regulations of the Republic Of Turkey.
Ukraine Restriction of Hazardous Substances
The equipment complies with the requirements of the Technical Regulation, approved by the Resolution of Cabinet of the Ministry of Ukraine as of December 3, 2008, № 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.
Vietnam RoHS
As of December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.
Green Product Features

• Reduced energy consumption during use and stand-by
• Limited use of substances harmful to the environment and health
• Easily dismantled and recycled
• Reduced use of natural resources by encouraging recycling
• Extended product lifetime through easy upgrades
• Reduced solid waste production through take-back policy

Environmental Policy

• The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
• Users should contact the local authorized point of collection for recycling and disposal of their end-of-life products.
• Visit the MSI website and locate a nearby distributor for further recycling information.
• Users may also reach us at [email protected] for information regarding the proper disposal, take-back, recycling, and disassembly of MSI products.

Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:

1. Take a 10-minute break for every 30 minutes of screen time.
2.  Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.

Copyright and Trademarks Notice
Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.
Technical Support
If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or a local distributor. Alternatively,
please visit https://www.msi.com/support/ for further guidance.

Revision
V1.0, 2022/03

Documents / Resources

Coolblue 323CQR ARTYMIS Series LCD Monitor [pdf] User Guide 323CQR, ARTYMIS Series LCD Monitor, LCD Monitor, 324CP, 3DB3

References

• SupportCenter | MSI Global - The Leading Brand in High-end Gaming & Professional Creation
• csr
• csr
• MSI - Redirect