Contents hide
1 CONIC SQW49 49*20w Matrix Zoom Moving Head
2 Safety Instructions
3 Technical Specifications
4 How to Control The Unit
5 DMX Channel List
6 Trouble shooting
7 Documents / Resources
7.1 References

CONIC LOGO

CONIC SQW49 49*20w Matrix Zoom Moving Head

CONIC SQW49 49 20w Matrix Zoom Moving Head

statement
The product has well capability and intact packing when leave factory. All of the user should comply with warning item and manual, any misuse cause of the damages are not included in our guarantee, and also can’t be responsible for any malfunction & problem owing to ignore the manual.

Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.

  • Unpack and check carefully there is no transportation damage before using the unit.
  • Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
  • It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
  • The unit is for indoor use only. Use only in a dry location.
  • The unit must be installed in a location with adequate ventilation, at least 50 cm from adjacent surfaces. Be sure that no ventilation slots are blocked.
  • Disconnect main power before replacement or servicing.
  • Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
  • Use safety cable when fixes this unit. Do not handle the unit by taking its head only, but always by taking its base.
  • Maximum ambient temperature is Ta: 40℃. Do not operate it where the temperature is higher than this Unit surface temperature may reach up to 85℃. Do not touch the housing bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving.
  • the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
  • Do not touch any wire during operation as high voltage might be causing the electric shock.

Warning:

  • To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
  • Do not open the unit within five minutes after switching off.
  • The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.

Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people.

Technical Specifications

  • Light Sources: 49*20W 4IN1 RGBW LED
  • Beam Angle: 4°- 46°
  • Power Consumption: 760W±5%,power factor PF≥0.95; standby power: 26W Power Voltage: AC 100-240V, 50/60Hz
  • Dimension: 477mm×272mm×579.5mm
  • Net Weight: 22.5 kg
  • Carton Package 1in1 size: 60*60*46cm
  • Gross Weight: 27.2 kg
  • Flight Case Package 2in1 size: 79*56*79cm
  • Gross Weight: 87.8 kg

Control

  • DMX Channel: 22/25/33/229/206 Channels
  • Control Modes: DMX512/Master-Slave/Auto Run/Music/Artnet

Pan/Tilt

  • Pan: 540°, accuracy 2.11°/step, fine-tuning accuracy: 0.008°
  • Tilt: 270° , accuracy 0.86 °/ step, fine-tuning accuracy: 0.0034 °
  • Pan/Tilt  Resolution: 8/16 bit
  • Tilt infinite rotation; Using photoelectric reset system

Construction

  • Display:180° reversible 1.8 inch TFT colorful Display
  • Data In/Out socket: 3-pin & 5-pin XLR sockets
  • Power Socket: Power Con in
  • Protection Rating: IP20

Features

  • Full light domain dimming, 65536 levels of dimming accuracy;
  • Fast strobe 1~25Hz; preset various kinds of color macro function; preset various kinds of effect macro function Led temperature protection & Speed of fan automatic adjustment based on the temperature of the head. Single LED control, zoom effect, Tilt infinite rotation.

3 lux DateCONIC SQW49 49 20w Matrix Zoom Moving Head 1

How to Control The UnitCONIC SQW49 49 20w Matrix Zoom Moving Head 2

Display:

  • MENU: To select the programming functions
  • DOWN: To go backward in the selected functions
  • UP: To go forward in the selected functions
  • ENTER: To confirm the selected functions

Set DMX Address Code

  1. Press “Menu” to “Set DMX Address”, and press “ENTER” keys to enter into
  2. Show “Set DMX Address DMX Address:001”, Press the “UP and DOWN” keys to amended
  3. Press “ENTER” keys to save and Exit, Press the “MENU” Keys does not save and Exit
 1.Pan Degree1)540 °, 2)360 °Pan running angle selection
2.Mic Sense001 – 100Sound sensitivity

adjustment

 

 

 

 

 

 

 

 

 

 

Menu

3.LanguageEnglishChinese
4.No Signal1.Black Out  2.Hold 
5.Fan Set1.Auto 2. Low 3.High 
6.ArtNet SetArtNet Enable：1.ON  2.OFF
2.Universe:0—255 
3.IP Mode：A.2.X.X.X Auto

B.10.X.X.X Auto C.Custom

4.Custom IP192.168.000.001
5.SubNetMask255.000.000.000
7.ResetYesReset
No
8.DefaultYesDefault
No
 

 

 

 

 

9.Adjust

Pass Word：up+down+up+down
1.Pan0 – 255
2.Tilt0 – 255
3.Focus0 – 255
4.Red0 – 255
5.Green0 – 255
6.Blue0 – 255
7.White0 – 255
AddressSetting from 001 – 512
 

 

 

 

 

Reverse

 

 

 

 

Forward or reversed setting

 

Pan

1.Yes
2.No
 

Tilt

1.Yes
2.No
 

Display

1.Yes
2.No
 

 

 

 

 

 

Information

1.CH

Value

 Each channel show CH

value

2.Temp

____

 Show the temperature of

led board

3.Soft

V.XXX

 Show the version

number

4.IP002.016.035.052Default IP
5.Mask255.000.000.000Default submask
 

 

 

 

 

Channel

1.22Channels 

 

 

 

Select channel mode

2.25Channels
3.33Channels
4.229Channels
5.206Channels
 

 

Mode

DMX 512
AUTO
SOUND
  1.Pan:0–255 
2.Pan Rotation：

0–255

 

 

 

 

 

Mode

 

 

 

 

 

Manual control

3.Tilt:0–255 

 

 

 

 

Manual control

4.Tilt Rotation：0–255
5.Focus:0–255
6.Red1：0–255
7.Greed1：0–255
8.Blue1：0–255
9.White1：0–255
10.Strobe1：0-255
11.Red2：0–255
12.Greed2：0–255
13.Blue2：0–255
14.White2：0–255
15.Strobe2：0-255
 

Alone/Master

1.Master 

Alone/Master

2.Alone

DMX Channel List

ChannelDisplayFunctionValue
CH-1RedRed dimming0 — 255
CH-2Red adjustmentRed adjustment0 — 255
CH-3GreenGreen dimming0 — 255
CH-4Green adjustmentGreen adjustment0 — 255
CH-5BlueBlue dimming0 — 255
CH-6Blue adjustmentBlue dimming0 — 255
CH-7WhiteWhite dimming0 — 255
CH-8White adjustmentWhite adjustment0 — 255
CH-9linear color temperatureNo effect0—4
Color temperature from warm to cold5—255
 

 

CH-10

 

 

Macro color

No effect0–9
Macro color 110–19
  Macro color 220–29
…. (10 numbers 1 macro color)….
CH-10Macro colorMacro color 24240–249
Macro color 25250–255
CH-11Dimmerdark to bright linear dimming0 — 255
CH-12Dimmer adjustDimmer adjustment control0 — 255
 

 

CH-13

 

 

Strobe

Turn on the light0—3
Synchro strobe speed

 

slow to fast (1HZ-25HZ)

 

 

4—203

Random strobe204–255
CH-14PanPan control0 — 255
CH-15Pan adjustmentPan adjustment control0 — 255
CH-16TiltTilt control0 — 255
CH-17Tilt adjustmentTilt adjustment control0 — 255
CH-18Pan/Tilt SpeedSpeed fast to slow0 — 255
 

 

 

 

CH-19

 

 

 

 

Tilt infinite rotation control

No Funtion0—55
Infinite rotation from slow to fast56—155
Infinite rotation reversal from slow to fast156—255
CH-20ZoomZoom0—255
  Mode -10 — 49
 

 

CH-21

 

 

Dimming Mode

Mode -250 — 99
Mode -3100—149
Mode -4150—255
 

 

CH-22

 

 

Reset

NO0-250
Reset within 5s251—255

Model 2 – 25Channels

ChannelDisplayFunctionValue
CH-1PanPan control0 — 255
CH-2Pan adjustmentPan adjustment control0 — 255
CH-3TiltPan control0 — 255
CH-4Tilt adjustmentTilt adjustment control0 — 255
CH-5Pan/Tilt speedSpeed from fast to slow0 — 255
 

 

CH-6

 

 

Tilt infinite control

No effect0—-55
Go from slow to fast56—-155
Reverse from slow to fast156—-25

5

CH-7ZoomZoom0 — 255
CH-8Dimmerdark to bright linear dimming0 — 255
 

 

 

 

CH-9

 

 

 

 

Strobe

Turn on the light0—3
Synchro strobe speed

 

From slow to fast (1HZ-25HZ)

4—203
Random strobe204–255
CH-10R dimmingdark to bright linear dimming0-255
CH-11G dimmingdark to bright linear dimming0-255
CH-12B dimmingdark to bright linear dimming0-255
CH-13W dimmingdark to bright linear dimming0-255
CH-14linear color temperatureNo effect0—4
Color temperature from warm to cold5—255
 

 

 

 

CH-15

 

 

 

 

Macro color

No effect0–9
Macro color 110–19
Macro color 220–29
….(10 numbers 1 macro color)….
Macro color 24240–249
Macro color 25250–255
  No0–2
pattern 13–5
pattern 26–9
CH-16Static pattern………(3 numbers 1 pattern)…..
pattern 59174–176
pattern 60177–255
 

 

 

 

 

 

 

 

 

CH-17

 

 

 

 

 

 

 

 

 

Dynamic pattern

NO0–9
dynamic pattern 110–11
dynamic pattern 212–13
……(2 numbers 1 pattern)…..
dynamic pattern 93194–195
dynamic pattern 94196–255
 

 

CH-18

Pattern translation

(With 17 channels)

 

 

Select a dynamic pattern scene

 

 

0-255

 

 

CH-19

Dynamic pattern speed (with 17 channels)No effect0—9
Forward, from fast to slow（with 17CH）10—132
Reverse, from slow to fast(with 17CH)133—255
CH-20Back color Rdark to bright linear dimming0-255
CH-21Back color Gdark to bright linear dimming0-255
CH-22Back color Bdark to bright linear dimming0-255
CH-23Back color Wdark to bright linear dimming0-255
CH-24 

 

 

 

Dimming Mode

Mode -10 — 49
Mode -250 — 99
Mode -3100—149
Mode -4150—255
 

 

CH-25

 

 

Reset

NO0-250
Reset within 5s251-255

Model 3 – 33Channel

ChannelDisplayFunctionValue
CH-1PanPan control0 — 255
CH-2Pan adjustmentPan adjustment control0 — 255
CH-3TiltPan control0 — 255
CH-4Tilt adjustmentTilt adjustment control0 — 255
CH-5Pan/Tilt speedSpeed from fast to slow0 — 255
 

 

CH-6

 

 

Tilt infinite control

No effect0—-55
Go from slow to fast56—-155
Reverse from slow to156—-255
  fast 
CH-7ZoomZoom0-255
CH-8Dimmerdark to bright linear dimming0 — 255
CH-9Dimmer adjustDimmer adjusting control0 — 255
CH-10 

 

Strobe

No effect0—3
Synchro strobe speed

From slow to fast (1HZ-25HZ)

 

 

4—203

Random strobe204–255
CH-11RedRed dimming0-255
CH-12Red adjustmentRed adjustment0-255
CH-13GreenGreen dimming0-255
CH-14Green adjustmentGreen adjustment0-255
CH-15BlueBlue dimming0-255
CH-16Blue adjustmentBlue dimming0-255
CH-17WhiteWhite dimming0-255
CH-18White adjustmentWhite adjustment0-255
CH-19 Mode -10 — 49
Mode -250 — 99
 Dimming ModeMode -3100—149
Mode -4150—255
CH-20linear color temperatureNo effect0—4
Color temperature

from warm to cold

5—255
 

 

 

 

CH-21

 

 

 

 

Macro color

No effect0–9
Macro color 110–19
Macro color 220–29
….(10 numbers 1 macro color)….
Macro color 24240–249
Macro color 25250–255
 

 

 

 

 

 

 

CH-22

 

 

 

 

 

 

 

Static pattern

No effect0–2
pattern 13–5
pattern 26–9
………… (3 numbers and one type)
pattern 59174–176
Pattern 60177–255
    
CH-23Dynamic patternNo effect0–9
dynamic pattern 110–11
dynamic pattern 212–13
………..…… (2 numbers and one type)
dynamic pattern 93194–195
dynamic pattern 94196–255
CH-24Pattern translation (with 23 channels)Select a dynamic pattern scene0–255
CH-25Dynamic pattern effect speedNO0–9
Forward, from fast to

slow(with 23CH）

10–132
Reverse, from slow to fast(with 23CH)133–255
CH-26Pattern effect fadePattern effect fade0-255
CH-27Background dimmingBackground 0-100% dimming0-255
CH-28Background strobeBackground strobe0-255
CH-29Pattern Back  RPattern effect R0-255
CH-30Pattern Back  GPattern effect G0-255
CH-31Pattern Back  BPattern effect B0-255
CH-32Pattern Back  WPattern effect W0-255
CH-33ResetNo effect0-250
Reset within 5S251-255

Model 4 – 229Channels

ChannelDisplayFunctionValue
CH-1PanPan control0 — 255
CH-2Pan adjustmentPan adjustment control0 — 255
CH-3TiltPan control0 — 255
CH-4Tilt adjustmentTilt adjustment control0 — 255
CH-5Pan/Tilt speedSpeed from fast to slow0 — 255
 

 

CH-6

 

 

Tilt infinite control

No effect0—-55
Go from slow to fast56—-155
Reverse from slow to fast156—-255
CH-7ZoomZoom0-255
CH-8Dimmerdark to bright linear dimming0 — 255
CH-9Dimmer adjustDimmer adjusting control0 — 255
CH-10 

 

Strobe

No effect0—3
Synchro strobe speed

From slow to fast (1HZ-25HZ)

 

 

4—203

Random strobe204–255
CH-11RedRed dimming0-255
CH-12Red adjustmentRed adjustment0-255
CH-13GreenGreen dimming0-255
CH-14Green adjustmentGreen adjustment0-255
CH-15BlueBlue dimming0-255
CH-16Blue adjustmentBlue dimming0-255
CH-17WhiteWhite dimming0-255
CH-18White adjustmentWhite adjustment0-255
CH-19 

 

 

 

Dimming Mode

Mode -10 — 49
Mode -250 — 99
Mode -3100—149
Mode -4150—255
CH-20linear color temperatureNo effect0—4
Color temperature from warm to cold5—255
 

 

 

 

CH-21

 

 

 

 

Macro color

No effect0–9
Macro color 110–19
Macro color 220–29
….(10 numbers 1 macro color)….
Macro color 24240–249
Macro color 25250–255
 

 

 

 

 

 

 

CH-22

 

 

 

 

 

 

 

Static pattern

No effect0–2
pattern 13–5
pattern 26–9
………… (3 numbers and one type)
pattern 59174–176
Pattern 60177–255
CH-23Dynamic patternNo effect0–9
dynamic pattern 110–11
dynamic pattern 212–13
………..…… (2 numbers and one type)
dynamic pattern 93194–195
dynamic pattern 94196–255
CH-24Pattern translation (with 23 channels)Select a dynamic pattern scene0–255
CH-25Dynamic pattern effect speedNO0–9
Forward, from fast to slow(with 23CH）10–132
Reverse, from slow to fast(with 23CH)133–255
CH-26Pattern effect fadePattern effect fade0-255
CH-27Background dimmingBackground 0-100% dimming0-255
CH-28Background strobeBackground strobe0-255
CH-29Pattern Back  RPattern effect R0-255
CH-30Pattern Back  GPattern effect G0-255
CH-31Pattern Back  BPattern effect B0-255
CH-32Pattern Back  WPattern effect W0-255
CH-33ResetNo effect0-250
Reset within 5S251-255
CH-34R1 LED dimming0–255R1 LED dimming
CH-35G1 LED dimming0–255G1 LED dimming
CH-36B1 LED dimming0–255B1 LED dimming
CH-37W1 LED dimming0–255W1 LED dimming
……..………………
CH-226R49 LED dimming0–255R49 LED dimming
CH-227G49 LED dimming0–255G49 LED dimming
CH-228B49 LED dimming0–255B49 LED dimming
CH-229W49 LED dimming0–255W49 LED dimming

Model 5-206Channels
(combined with ArtNet,1~10 channels are controlled by ordinary DMX512 , 11~206channels are controlled by ArtNet )

ChannelDisplayFunctionValue
CH-1PanPan control0 — 255
CH-2Pan adjustmentPan adjustment control0 — 255
CH-3TiltPan control0 — 255
CH-4Tilt adjustmentTilt adjustment control0 — 255
CH-5Pan/Tilt speedSpeed from fast to slow0 — 255
 

 

CH-6

 

 

Tilt infinite control

No effect0—-55
Go from slow to fast56—-155
Reverse from slow to fast156—-255
CH-7ZoomZoom0-255
CH-8ResetNo effect0-250
  Reset within 5S251-255
CH-9Dimmerdark to bright linear0 — 255
  dimming 
CH-10 

 

Strobe

No effect0—3
Synchro strobe speed

From slow to fast (1HZ-25HZ)

 

 

4—203

Random strobe204–255
dynamic pattern 93194–195
dynamic pattern 94196–255
CH-11R1 LED dimming0–255R1 LED dimming
CH-12G1 LED dimming0–255G1 LED dimming
CH-13B1 LED dimming0–255B1 LED dimming
CH-14W1 LED dimming0–255W1 LED dimming
……..………………
CH-203R49 LED dimming0–255R49 LED dimming
CH-204G49 LED dimming0–255G49 LED dimming
CH-205B49 LED dimming0–255B49 LED dimming
CH-206W49 LED dimming0–255W49 LED dimming

ShapeCONIC SQW49 49 20w Matrix Zoom Moving Head 3

Trouble shooting

Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

  1. Check the connection of power and main fuse.
  2. Measure the mains voltage on the main connector. 3. Check the power on LED.

B. Not responding to DMX controller

  1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
  2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
  3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one.
  4. Try to use another DMX controller.
  5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.

C. One of the channels is not working well

  1. The stepper motor might be damaged or the cable connected to the PCB is broken.
  2. The motor’s drive IC on the PCB might be out of condition.

Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

  • Clean with soft cloth using normal glass cleaning fluid.
  • Always dry the parts carefully.
  • Clean the external optics at least every 20 days.
  • Clean the internal optics at least every 30/60 days.

Documents / Resources

CONIC SQW49 49*20w Matrix Zoom Moving Head [pdf] User Manual
SQW49, SQW49 49 20w Matrix Zoom Moving Head, 49 20w Matrix Zoom Moving Head, Matrix Zoom Moving Head, Zoom Moving Head, Moving Head, Head, HCW49

References

Leave a comment

Your email address will not be published. Required fields are marked *