Cloudy Bay logo

INSTALLATION INSTRUCTIONS
CBST03BLXX12V
PLEASE READ CAREFULLY BEFORE INSTALLING THE FIXTURE

Save these instructions, as you may need them at a later date.

CBST03BLORB12V Indoor or Outdoor Step Light

Thank you for purchasing CloudyBay Smart LED Lighting Fixtures.
 Indoor/Outdoor Step LightCloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light

GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, contact and obtain the services of a qualified electrician. Use UL or IEC-approved wire only for input/output connections. Remove fixture and mounting components from the box, and make sure that no parts are missing, by referencing the illustration in the illustration instructions.

  1. warning 2Make sure you have low voltage transformer or adaptor before you start your project
  2. Make sure you connect your step light to a proper low voltage power source
  3. Improper voltage input may destroy your lights and make your warranty invalid

warning 2Turn the power off before installation, inspection, or removal.
Use all necessary precautions while performing this procedure.
Consult a qualified electrician to ensure the correct branch circuit conductor. Min 90°C supply conductors.
This Integrated LED Fixture has no lamp/bulb to replace.

DON’T SUBMERGE THE LIGHT BODY INTO WATER INSTALLING IT IN AN AREA WITH HIGH SALTY MOISTURE OR A CORROSIVE ENVIRONMENT WILL LEAD TO FAST CORROSION SINCE IT IS NOT DESIGNED FOR THIS PURPOSE

TROUBLESHOOTING

If the fixture does not light:

  • Check the switch to ensure that there are no defects.
  • Check fuse/circuit breaker for trips, then check wiring connections.
    Cloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light - icon

CLEANING AND MAINTENANCE:

CAUTION: Ensure fixture temperature is cool enough to touch.
DO NOT clean or perform maintenance while the fixture is energized.Cloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light - icon 1

  • Clean lens and fixture with a non-abrasive cleaning solution.
  • Do not open fixtures to clean LED. Do not touch the LED.
  • Do not spray liquid directly on to LED, LED driver or wiring.

3-Year Limited Warranty

LIMITED WARRANTY: This fixture is warranted to be free from defects in workmanship and material for up to 3-years. Based upon reasonable household usage, when used in accordance with the package and included instructions. If this fixture does not last for the time period guaranteed, the manufacturer will send you a replacement fixture upon receipt of the returned fixture, register the receipt, and proof of purchase. To contact us, please email us at [email protected] to find out how to return the fixture. We are committed to making high-quality products. Returning the fixture will help us monitor and further improve product quality. This replacement is the sole remedy available, and LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED.Cloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light - fig

  1. OUTLET BOX (EXCLUDED)
  2. FIXTURE SCREWS
  3. MOUNTING BRACKET
  4. BLACK FiXTURE WIRE ONE
  5. BLACK FIXTURE WIRE TWO
  6. WIRE NUTS
  7. LIGHT BODY INTEGRATED WITH FACE COVER *
  8. LOW VOLTAGE WIRE ONE
  9. LOW VOLTAGE WIRE TWO
  10. WASHER

*(2PCS 6×25 and 2PCS 6×16 SCREW INCLUDED)
+ Please add washers between the MOUNTING BRACKET and this type of Junction Box so that a light body can be inserted into the mounting bracket

Cloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light - icon3Please follow these steps for installation.Cloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light - icon3

  1. Fix the Mounting Bracket(3) to the OUTLET BOX(1) with attached FIXTURE SCREW(2)
  2. Pull out low voltage wires from OUTLET BOX(1). Unlike Line voltage products, you don’t need to specify live wire/ neutral wire. Connect LOW VOLTAGE WIRE ONE(8) to BLACK FIXTURE WIRE ONE(4), LOW VOLTAGE WIRE TWO(9) TO BLACK FIXTURE WIRE TWO(5). Please make sure the wires are firm connected, and seal the WIRE NUTS(6) with silicone to ensure stable performance in long term.
  3. Check the MOUNTING BRACKET(3) is fixed flat on OUTLET BOX(1)’s surface, press the SPRING CLIP evenly into the MOUNTING BRACKET(3) until all clips have a good connection with MOUNTING BRACKET(3)’s edge.
  4. Installation Complete For Outdoor application: caulk the connection area between face cover and wall with outdoor rated sealant for stable performance.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Documents / Resources

Cloudy Bay CBST03BLORB12V Indoor or Outdoor Step Light [pdf] Instruction Manual
CBST03BLORB12V, 2A4FVCBST03BLORB12V, CBST03BLORB12V, Indoor or Outdoor Step Light, CBST03BLORB12V Indoor or Outdoor Step Light, Smart LED Lighting Fixtures

Leave a comment

Your email address will not be published.