Categories: clearwater LIGHTS

clearwater LIGHTS Low Beam/High Beam Glendina LED Light Universal Kit Instruction Manual

clearwater LIGHTS Low Beam/High Beam Glendina LED Light Universal Kit

Specs and Parts List

Please be sure to read our instructions thoroughly before attempting installation.

The Glendina makes your motorcycle more visible to oncoming traffic during the day, and at night provides a wide pattern of light for more side illumination. They are a combination of a fog and visibility lights meant to make you more conspicuous. If you ride mostly on the street, during the day, Glendina is a good choice to help make you safer and more visible. This universal Glendina kit can fit over 300 bikes!

  • Modes: Low Beam/High Beam
  • LEDs: Three LEDs (ea)
  • Brightness: 900 Lm on High Beam, 200 Lm on Low Beam (ea)
  • Power: 10W/1A on High Beam (ea), 1W/0.1A on Low Beam (ea)
  • Optic: Driving Beam
  • Size: 1.8” Diameter
  • Weight: 4 oz (ea)

Mounting The Lights

  • First, park the motorcycle on hard pavement or concrete to insure the bike will be stable during the installation. If you can mount the bike on a stand with tie-down straps, this will help secure the motorcycle.
  • Follow the manufacturers guidelines for disconnecting the battery. This is important to prevent damage to the electrical system.
  • Pre-assemble the lights to the mounting brackets using the shoulder washers (if needed), along with the spacers and new bolts. Add 1 or 2 plastic washers to shoulder washer to make up difference in thickness of front fender if needed. Make sure to assemble one side at a time.
  • Gently screw all bolts in hand tight. Inspect the bolt length and spacer alignment before tightening the bolts. Follow the pictures below as a reference.
  • The mounting bracket can be mounted facing down (shown) or up to give the desired adjustability range.

Wiring

  • Be sure to route wires so that they cannot become tangled or caught in either a suspension or steering component. Check movement of both steering and suspension before riding the bike.
  • It is helpful to follow existing wire routing.
  • Before connecting wires together on the lights and bike, be sure to disconnect the negative terminal from the battery first, then the positive terminal.
  • Use the wiring diagram on Page 4 as reference.
  • Connect small red wires coming out of lights with a Posi-tap to a switched hot wire. This means one that turns off with the key. A low beam wire coming from the headlight assembly can often be used. Make sure both red wires are connected to the Posi-tap together. Refer to the Posi-tap installation instructions on Page 5.
  • Connect small black wires coming out of lights with a Posi-tap to a ground wire coming out of the headlight assembly. Or any ground on the bike.
  • Connect small yellow wires coming out of lights with a Posi-tap to a high beam wire (Voltage when high beam is switched on) coming out of the headlight assembly

High Beam Feature:

When your Glendina lights are installed, they will run at a lower brightness setting when the motorcycle headlight is switched to low, and 100% brightness when the motorcycle headlight is switched to high.

Wiring Diagram

How To Use Posi-Taps

  1. Strip black sleeve back 2.5” and strip the six wires back 0.5”
  2. Twist common colored wires together.
  3. Completely unscrew bottom cap from Posi-Tap.
  4. Feed the twisted wires through the bottom portion of the Posi-Tap.
  5. Hold onto the base to ensure the wires do not slip out of the bottom of the Posi-Tap, attach to Posi-Tap body and tighten.
  6. Unscrew the gray cap of the Posi-Tap.
  7. Twist the two common coloed wires backwards so when threading the grey cap back on, the wires will be in a relaxed state and not twisted.
  8. Slide the wire you wish to tap into through the slot in the cap.
  9. Re-attach the body of the Posi-Tap and tighten, this will relax the twist applied in step 7.

Aligning The Lights + Tips

Ask an assistant to help you with this procedure. Make sure the bike is on level ground and have an assistant sit on the bike. Press a level against the face of the light, and adjust its angle. The goal is to adjust the lights so that the light is level with the ground. Passengers and luggage may alter the alignment of the light, so further adjustments may be needed. You may find that a slight downward angle (5degrees) is helpful.

Do Not Kink The Grommet

To maintain the integrity of the water sealling grommet, do not kink, deform or put pressure on the grommet when dressing the wires during install of Clearwater Lights.

Thank you for purchasing your Clearwater Lights. We hope this product will help make you a safer rider. Please feel free to send us comments or suggestions at any time. We learn from you. Visit our website for more exciting products to help you see better at night.

Documents / Resources

clearwater LIGHTS Low Beam/High Beam Glendina LED Light Universal Kit [pdf] Instruction Manual
Low Beam, High Beam, Glendina LED Light Universal Kit, Low Beam Glendina LED Light Universal Kit, High Beam Glendina LED Light Universal Kit, Low Beam High Beam Glendina LED Light Universal Kit
Share

Recent Posts

audio-technica AT-ONE UHF Wireless Microphone System User Guide

AT-ONE UHF Wireless Microphone System Basic Specifications RF Power 10mW Operating Temperature +5 to +45…

6 mins ago

PowerA 1516956-01 (NA) Twin Charging Station for DualSense Wireless Controllers User Manual

1516956-01 (NA) Twin Charging Station for DualSense Wireless Controllers Customer Service Service client Kundendienst Servicio…

8 mins ago

audio-technica AT-ONE Series Wireless Systems Microphones User Manual

AT-ONE Series Wireless Systems Microphones AT-ONE Wireless Systems User Manual UHF Wireless Systems RF AF…

8 mins ago

YOTTA ENERGY DPI-208 Grid Support Utility Interactive Microinverter User Manual

DPI-208 Grid Support Utility Interactive Microinverter DPI-208 & DPI-480 Installation / User manual Ver. 1.0…

8 mins ago

auto Land PS-M2 Vehicle Power Stabilizer User Guide

PS-M2 Vehicle Power Stabilizer

22 mins ago

PHILIPS S5466 Wet and Dry Electric Shaver User Manual

S5466 Wet and Dry Electric Shaver 5000 Series S5466 2 5 min 2 1 hr…

23 mins ago