Categories: clearwater LIGHTS

clearwater LIGHTS 1635968474 CAN Opener User Manual

clearwater LIGHTS 1635968474 CAN Opener

Features

 

Summary of Features

  1. Independent dimming feature
    1. Independent dimming of two sets of Clearwater lights using the BMW Wonder Wheel (handlebar mounted rotary dimmer is included for non-Wonder Wheel bikes)
    2. The dimmer has 11 brightness levels. Starting at 3%, then increasing from 10-100% in 10% increments
  2. Automatic Dimmer
    1. Dimmer setting compensates automatically using the bike’s photocell
    2. Factory preset for day, night, and high beam illumination
  3. On/Off function for Erica/Krista/Sevina/Darla lights
    No separate switch is required, uses factory turn signal cancel button
  4. Turn Signal Dimming
    Clearwater Lights can be set to dim while turn signals are activated.
  5. Horn Activation Mode
    Programmable to illuminate or strobe with horn button (off road use only)
  6. High Beam Mode
    Clearwater Erica/Krista/Sevina lights programmable to activate or strobe (off-road use only) with a flash-to-pass button
  7. Hazard Flasher Alert Mode
    Programmable to strobe when switching the hazard button on/off (off-road use only)
  8. Clearwater Brake Light Module (optional)
    Programmable LED brake module includes standard brake/tail California-legal strobe mode, and speed-sensitive mode
  9. Auxiliary CANopener relay drives
    1. Auxiliary turn on (1/4 amp maximum) -YELLOW wire
    2. Auxiliary horn (1/4 amp maximum) – GRAY wire
    3. Auxiliary high beam relay drive (1/4 amp maximum) – GREEN wire
      WARNING: Do not connect auxiliary accessories without a relay!
  10. Factory Default Reset
    Reset all functions to the default settings

Mounting Locations

The CANopener module can be found mounted under the seat on most liquid cooled BMW’s.

CANopener location on an R1200GSW/GSAW

Mounting Locations

operation

DIMMING CONTROL (Wonder Wheel equipped bikes) Information on Dimming: Two modulated brightness channels are adjustable using the Wonder Wheel. Each channel is programmable for (11) brightness settings (3, 10-100%) in three different modes (day, night, and high beam). Settings are stored, and will be remembered when restarting the bike or disconnecting the battery. The dimmer is programmed at the factory for the most useful day/night settings. Follow the procedure below to enter dimming mode

  • Step 1: To enter into dimming mode, first press & release the TSC button shown in the figure to the right.
  • Step 2: To adjust Glenda/Darla lights, hold the Wonder Wheel to the Left for 2 seconds. To adjust Krista/Erica/Sevina lights, hold Wonder Wheel to the Right for 2 seconds. The lights should flash twice. The brightness level can then be adjusted by rotating the Wonder Wheel forward and back.
  • Step 3: To exit dimming mode, press and release the TSC button again. This will lock in the brightness setting.

Note – Remember that each set of lights are adjustable for day and night. Day and night settings are automatically selected by the ambient light level reaching the bike’s photocell. To adjust the night dimmer, simply cover the dash display using your hand or a towel. Activating the high beam switches the lights to 100%. If you want your high beam dimmed, simply perform the same commands (above) in high beam.

DIMMING CONTROL (Non-Wonder Wheel) If the motorcycle does not have the GPS Prep Package (Wonder Wheel), your light kit will come equipped with a handlebar mounted knob for dimming control. Separate day/night settings, seperate channel dimming, and strobe functions are not available.

Default Settings:

DIMMING CONTROL

ON/OFF FUNCTION FOR ERICA/KRISTA/SEVINA
The Krista/Erica/Sevina lights can be manually deactivated. Toggle these modes by holding the TSC button for two seconds.

  • Mode 1 – on and dimmable (default)
  • Mode 2 – off

(Krista/Erica/Sevina lights can automatically be shut off if the TSC button is pressed and released 3 times. This is great if the rider forgets is the lights are on or off.)

TURN SIGNAL DIMMING
The front Clearwater lights, and Billie tail light can be programmed to dim when the turn signals are activated. To toggle the Turn Signal Dimming mode on and off, press and release the (TSC) button, hold the right Turn Signal while pressing and releasing the front (hand) brake lever 5 times.

HORN ACTIVATION MODE
The Clearwater lights can be programmed for three different modes when the horn button is pressed. Toggle these modes by pressing and releasing the TSC, then hold the front (hand) brake lever and press and release the TSC (5) times. The brake and Clearwater lights will flash to indicate the mode selected:

  • Mode 1 – horn does not affect lights
  • Mode 2 – horn activates lights 100% (default)
  • Mode 3 – horn strobes lights (if two sets of Clearwater lights are installed, they will alternate flashing

HIGH BEAM MODE
The Krista/Erica/Sevina lights can be programmed for three modes of operation in conjunction with high beams. Toggle these modes by pressing and releasing the (TSC) button, holding the front brake lever then pressing and releasing the FTP button (See Fig. A below) (5) times:

  • Mode 1 – All Clearwater lights turn on 100% when high beam or flashto-pass is pressed. Krista/Erica/Sevina lights will not turn on with high beam or flash-to-pass if Krista/Erica/Sevina lights are switched off.
  • Mode 2 – HIGH BEAM ACTIVATION. All Clearwater lights turn on 100% when high beam or flash-to-pass is pressed. Krista/Erica/Sevina lights will turn on when High beam or flash-to-pass is pressed, even when Krista/Erica/Sevina lights are switched off (default on Version 1.6 or greater).
  • Mode 3 – HIGH BEAM FLASH MODE: Same as Mode 2, but lights will flash for 2 seconds when the flash-to-pass button is triggered 3 times.

HAZARD FLASHER ALERT MODE
The Clearwater lights can be programmed to strobe when the hazard flasher button is toggled on. Toggle these modes by pressing and releasing the (TSC) button, holding down the hazard flasher button, then press and release the (hand) brake lever (5) times:

  • Mode 1 – OFF, no flash with emergency flasher button (default)
  • Mode 2 – strobe with emergency flasher when the button is held down (Version 1.90 or earlier), or toggled on (Version 1.91 and later). If two sets of Clearwater lights are installed, they will alternate flashing.
    WARNING: The use of strobe mode may not be legal on public highways. Check your local regulations. This mode is intended for parades and escorts under certain conditions.

AUXILIARY CANopener RELAY DRIVES

  • Auxiliary turn on (1/4 amp maximum) Useful for turning on aux fuse boxes or a PDM-60.
  • Auxiliary horn (1/4 amp maximum) Useful for adding an aux air horn. MUST use a relay.
  • Auxiliary high beam relay drive (1/4 amp maximum) Useful for adding an aux high beam.

FACTORY DEFAULT RESET

To reset the CANopener to the factory settings, press and release the (TSC) button, hold the left turn signal switch, and press and release the flash-to-pass button (6) times. All factory preset dimmer levels and modes will be selected. A successful reset is indicated by five flashes of all Clearwater lights

DIXI FUNCTIONALITY

Dixi lights operate similarly to two sets of our lights. The Outer Ring of LEDs (A) can be turned on and off by holding in the TSC for 2 seconds just like a set of Krista’s, Ericas or Levinas. The Inner LEDs (B) are designed to come on with the engine just like a set of Darla’s but can be shut off (Version 2.3+) by holding the TSC Left for 5 seconds and turned back on by holding the TSC to the right for 3 seconds. The Inner and Outer rings of LEDs is dimmed together using the same dimming operation as the Krista/Erica/Sevina channel. Refer to Page 5, Step 2 for further dimming operation details.

Documents / Resources

clearwater LIGHTS 1635968474 CAN Opener [pdf] User Manual
1635968474 CAN Opener, 1635968474, CAN Opener
Share

Recent Posts

blyss 3663602844723 449W Curved Chrome Towel Warmer Instruction Manual

3663602844723 449W Curved Chrome Towel Warmer 3663602844624 3663602844631 3663602844648 3663602844655 3663602844662 3663602844679 3663602844686 3663602844693 3663602844709…

24 seconds ago

CAMBRIDGE AUDIO Edge W Power Amplifier Instruction Manual

Edge W Power Amplifier EN DE FR ES IT SV RU P.02 P.10 P.18 P.26…

7 mins ago

JOYO YS-10B Portable Amplifier Musical Instrument Speaker Owner’s Manual

YS-10B Portable Amplifier Musical Instrument Speaker FCC Statement This equipment has been tested and found…

7 mins ago

ALESIS Drums Nitro Mesh Kit Instructions

Drums Nitro Mesh Kit Nitro Mesh Kit ­ Frequently Asked Questions Can I fold this…

12 mins ago

IKEA MATÄLSKARE Forced Air Oven Stainless Steel Instruction Manual

MATÄLSKARE Forced Air Oven Stainless Steel MATÄLSKARE CN GB www. IKEA.com ENGLISH The IKEA after…

12 mins ago

INVENTUM PW810W Bathroom Scale Instruction Manual

PW810W Bathroom Scale BATHROOM SCALE · PERSONENWAAGE · PÈSE PERSONNE personenweegschaal PW810W · gebruiksaanwijzing ·…

13 mins ago