CLASSEN logo

POWERSTEER AERATOR
TA25DA
MAN4175385
Rev. C
CLASSEN TA25DA Powersteer Aerator
PARTS MANUAL
Operators Manual 4175836
CLASSEN logo 1

CALIFORNIA
Proposition 65 Warning
Diesel engine exhaust and some of its constituents are known to the State of  California to cause cancer, birth defectsand other reproductive harm.
Warning WARNING
The engine exhaust from this product contains chemicals known to the State  of California to cause cancer, birthdefects or other reproductive harm.
CALIFORNIA
Proposition 65 Warning
Battery posts, terminals, wiring insulation, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WASH HANDS AFTER HANDLING.
AERATOR

IMPORTANT MESSAGE
Thank you for purchasing this Classen product. You have purchased a world class product, one of the best designed and built anywhere.
This product comes with Parts and Operator’s Manuals. The useful life and good service you receive from this product depends to a large extent on how well you read and understand this manual. Treat this product properly and adjust it as instructed, and it will give you many years of reliable service.
See a Classen dealer for any service or parts needed. Classen service ensures that you continue to receive the best results possible from Classen products. You can trust Classen replacement parts because they are manufactured with the same high precision and quality as the original parts.
Classen designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this product only as directed in the manual, keep it in good repair and follow safety warnings and instructions. You’ll always be glad you did. Classen 1028 Street Road Southampton, PA 18966

SAFETY

NOTICE !!!
Unauthorized modifications may present extreme safety hazards to operators and bystanders and could also result in product damage.
Classen strongly warns against, rejects and disclaims any modifications, add-on accessories or product alterations that are not designed, developed, tested and approved by Classen Engineering Department.
Any Classen product that is altered, modified or changed in any manner not specifically authorized after original manufacture–including the addition of “after-market” accessories or component parts not specifically approved by Classen–will result in the Classen Warranty being voided.
Any and all liability for personal injury and/or property damage caused by any unauthorized modifications, add-on accessories or products not approved by Classen will be considered the responsibility of the individual(s) or company designing and/or making such changes. Classen will vigorously pursue full indemnification and costs from any party responsible for such unauthorized post-manufacture modifications and/or accessories should personal injury and/or property damage result.
This symbol means:
Warning ATTENTION!
BECOME ALERT!
Your safety and the safety of others is involved.
Signal word definitions
The signal words below are used to identify levels of hazard seriousness. These words appear in this manual and on the safety labels attached to Classen machines. For your safety and the safety of others, read and follow the information given with these signal words and/or the symbol shown above.
Warning DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
Warning WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
Warning CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices or property damage.
Warning CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, MAY result in property damage

Schiller Grounds Care, Inc.
1028 Street Road
Southampton, PA 18966 U.S.A
Phone: 215-357-5110
Fax: 215-357-8045
MODEL NUMBER
SERIAL NUMBER
MODEL NUMBER: This number appears on sales literature, technical manuals and price lists.
SERIAL NUMBER: This number appears only on your machine. It contains the model number followed consecutively by the serial number. Use this number when ordering parts or seeking warranty information.
MAINTENANCE SAFETY
In general

  • Maintain machine according to manufacturer’s schedule and instructions for maximum safety and best results.
  • Park machine on level ground.
  • Never allow untrained personnel to service machine.
  • Guards should only be removed by qualified maintenance technician for maintenance/service. Replace when work is complete.
  • Adjust or repair only after the engine has been stopped and the tines have stopped moving.
  • Disconnect spark plug wire(s) before doing any maintenance.
  • Replace parts if worn, damaged or faulty. For best results, always replace with parts recommended by the manufacturer.
  • Do not dismantle the machine without releasing or restraining forces which may cause parts to move suddenly.
  • Provide adequate support, e.g. jack stands for lifted machine or parts if working beneath.
  • Do not put hands or feet near or under rotating parts.
  • Clean up spilled oil or fuel thoroughly.
  • Replace faulty mufflers.
  • To reduce fire hazards, keep the engine, muffler, and fuel storage area free of grass, leaves, debris buildup or grease.

CLASSEN TA25DA Powersteer Aerator - icon Tines
The tines are sharp and can cut.
Use extra caution when handling. Remove obstructions with care.
Wrap the tines or wear gloves.

  • Only replace tines. Never straighten or weld.
  • Keep other persons away from tines.

CLASSEN TA25DA Powersteer Aerator - icon 1 Fuel

  • Petrol (gasoline) and diesel fuels are flammable; petrol  (gasoline) vapors are explosive. Use extra carewhen handling.
  • Store only in containers specifically designed for fuel.
  • When refueling or checking fuel level:
  • Stop the engine and allow to cool;
  • Do not smoke;
  • Refuel outdoors only;
  • Use a funnel;
  • Do not overfill;
  • If fuel is spilled, do not attempt to start the engine until the spill is cleaned up and vapors have cleared.
  • Replace caps on fuel containers and tanks securely.

Sparks from static electricity can start fires or cause explosions. Flowing fuel can generate static electricity.
To prevent static electricity sparks:

  • Keep fuel containers electrically grounded. Do not fill containers in a vehicle or on a truck or trailer bed with a plastic liner. Fill containers on the ground away from the vehicle.
  • When practical, remove petrol (gas) powered equipment from the truck or trailer and refuel it on the ground. If equipment must be refueled on the truck or trailer, refuel from a portable container rather than a dispenser nozzle.
  • Keep the dispenser nozzle in contact with the rim of the fuel tank or container opening until fueling is complete. Do not use a nozzle lock-open device.

Storage Safety

  • Stop the engine and allow to cool before storing.
  • Drain the fuel tank outdoors only.
  • Store fuel in an approved container in a cool, dry place.
  • Keep the machine and fuel containers in a locked storage place to prevent tampering and to keep children from playing with them.
  • Do not store the machine or fuel container near heating appliances with an open flame, such as a water heater, or an appliance with a pilot light.
  • Keep gasoline (petrol) storage area free of grass, leaves and excessive grease to reduce fire hazard.
  • Clean grass and debris from tines, drives, mufflers and engine to help prevent fires.

INTRODUCTION

THANK YOU
Thank you for purchasing a CLASSEN Aerator
READ THIS MANUAL
Read your operator’s manual carefully in its entirety. It con-  tains safety, operating, maintenance, and adjustment instruc- tions for your Aerator. By following the operating and mainte-nance instructions you will prolong the life of your equipment  and maintain its maximum efficiency. Failure to do so could result in personal injury or equipment damage.  This manual should be considered a permanent part of yourAerator and should remain with it if you sell it.
WARRANTY
Refer to last page.
MEASUREMENTS
U.S. Units of measure are used in this manual.
SERIAL NUMBERS
Write frame and engine serial numbers, plus model numbers in “Owner’s Record” section below. You may need these  numbers when you order parts. The serial number stick plateis located on the right rear of the Aerator frame.
ORDERING PARTS 
When ordering parts, always give the serial number and model of your Aerator as well as the quantity, part number and description of the part needed.
DIRECTIONS
“Right Hand” and “Left Hand” sides of the Aerator are deter- mined by facing the “back” of the Aerator as you would oper- ate the machine.

OWNER’S RECORD

DATE PURCHASED _______________________
AERATOR MODEL NUMBER _______________________
AERATOR SERIAL NUMBER _______________________
ENGINE MODEL NUMBER _______________________
ENGINE SERIAL NUMBER _______________________

PRE-DELIVERY CHECK LIST

Check the following before you deliver the Aerator to the customer.

  1. Guards and shields fastened in place.
  2. Decals fastened and legible.
  3. Weight bar installed.
  4. Gas lever on engine turned on.
  5. All lubrication points greased.
  6. 6:1 gearbox oil level.
  7. Engine oil level.
  8. Air cleaner.
  9. Touch up scratches.
  10. Chain(s) tight.
  11. Lowering handle working properly.
  12. Control handle(s) working to tighten V-belt(s).
  13. Add fuel, start engine, test run.
    DATE SET UP __________/__________/__________

DELIVERY CHECK LIST

Review the operators manual with the customer.

  1. Schiller Grounds Care, Inc. warranty.
  2. Safe operation and service.
  3. How to use controls.
  4. Operating the machine correctly.
  5. Transporting the Aerator.
  6. Correct fuel and lubricants.
  7. Daily and periodic inspections.
  8. Changing oil after break-in period.
  9. Servicing the Aerator regularly and correctly.
  10. Schiller Grounds Care, Inc. parts and service.
  11.  Give the customer the operators manual and encourage customer to read it.
    DATE DELIVERED __________/__________/________
    SIGNATURE __________________________________

PARTS SECTION

MAIN FRAME ASSEMBLY

FIGURE 1CLASSEN TA25DA Powersteer Aerator - fig1

ITEMPART NO.DESCRIPTIONQTY
120942DECAL, “DANGER”1
2C5000835/16” FLAT WASHER8
3C5001155/16” LOCK WASHER8
4C5001405/16” x 3/4” BOLT3
54171825DECAL, CLASSEN PRO2
64175359S-GUARD, PULLEY, ASSEMBL1
74173339DECAL, “POWERSTEER”2
8C500147BOLT, 5/16-18 x 1-1/21
9C5001015/16” NUT5
10C5001635/16” x 3/4” CARRIAGE BOLT4
11C5001695/16” LOCK NUT4
12C400393.17CHAIN GUARD, (L.H.)1
13C400394.17CHAIN GUARD, (R.H.)1
14C5001343/8” x 1-1/4” BOLT2
15C400085.17CLUTCH ARM, (R.H.)1
16C5000423/8” FLAT WASHER12
17C5000413/8” LOCK NUT2
18C5000291/4” x 3/4” BOLT4
19C5001361/4” NUT4
20C5000011/4” x 28 GREASE FITTING2
21C5001371/4” LOCK WASHER4
22C5000113/16” x 1” SQ. KEY4
23C100021BRASS BUSHING4
24C400021.17IDLER ARM, (R.H.)1
25C5001293/8” NUT7
26C5001303/8” LOCK WASHER4
27C100010IDLER PULLEY2
28C5000913/8” x 2” BOLT2
29C400087.17IDLER ARM, (L.H.)1
30C400083.17CLUTCH ARM, (L.H.)1
31C5001703/8” x 4-1/2” BOLT2
32C5001145/16” x 2-1/4” TAP BOLT4
33 34 35C300049.17 4174338.7 C400079.17CHAIN TIGHTENING PLATE LINKAGE ARM SPLIT DRIVETA-25D MAIN FRAME4
364171963DECAL, “CLASSEN”2
374174350WEIGHT BAR1
38C400015.7SPRING ARM3
39C100040FRAME SPRING1
40C1000318” REAR TIRE ASSEMBLY2
41C200012KEYED SHAFT2
42C300009.17WEIGHT STOP FLAT2
43C5001943/4” FLAT WASHER1
44C5001641/4” FENDER WASHER1
45 46C400026.7 C300006.7AXLE SUPPORT ARM, (RH) PIVOT FLAT6
47C5001311/2” LOCK NUT12
48C5001351/2” x 2-1/2” BOLT2
49C300005.7BUSHING SPACER 502
50C5001491/2” x 2” BOLT2
51C5001061/2” NUT4
52C5000061/2” LOCK WASHER2
53C5001741/2” x 1-3/4” BOLT2
54C100049PIN, REAR AXLE2
55C5000341/2” FLAT WASHER8
56*2000577DECAL, “ALL GUARDS”1
57*4171157DECAL, “POWERSTEER”.1
58*C100055DECAL, “SERIAL NUMBER”1
59*C100257DECAL, “PATENT”1
60*C100073LUBRICATION TAG1
61C5000433/8” x 1” BOLT1
62C5000965/32” x 3” BRIDGE PIN CLIP2
63C400025.7AXLE SUPPORT ARM (LH)1
64C5001653/8” X 4-1/2” BOLT1

*NOT ILLUSTRATED

POWER TRAIN ASSEMBLY

FIGURE 2

CLASSEN TA25DA Powersteer Aerator - POWER

ITEMPART NO.DESCRIPTIONQTY
1C100039BX-43 V-BELT2
2C1000133/4” BEARING w/ COLLAR4
3 4C200022 C500101JACK SHAFT ASSEMBLY, (R.H.) 5/16” NUT1
5C5001155/16” LOCK WASHER21
6C5000835/16” FLAT WASHER15
7C5001733/16” x 7/8” HALF MOON KEY20
8C5000745/16” x 1-3/4” BOLT2
941749298” PULLEY & HUB w/o KEY8
10 11C200021 C100037JACK SHAFT ASSEMBLY, (L.H.) 4.0 HP HONDA ENGINE2
12C5001475/16” x 1-1/2” BOLT1
13C1000383” x 3/4” PULLEY w/ HUB1
14C5002313/16” x 1-3/4” SQ. KEY79
15C1000041” BEARING w/ COLLAR2
16C5001501/2” x 1-1/2” BOLT1
17C5000341/2” FLAT WASHER4
18C5001311/2” LOCK NUT8
19 20C300011.7 C200009OUTSIDE DRUM SHAFT SPACER#40 x 36 SPROCKET & HUB15
21C3001312” MACHINERY WASHER8
22C5000031/4” x 7/8” HALF MOON KEY2
23 24C700017.7 C100032.7TINE DISC SHAFT ASSEMBLY  PLUGGING TINE2
25C5001695/16” LOCK NUT2
26C5001061/2” NUT2
27C5000061/2” LOCK WASHER2
28C100043IDLER PULLEY36
29C5001741/2” x 1-3/4” BOLT84
30 31 32C100151 C100155 C300057.7#40 x 75 PITCH CHAIN w/ LINK  1” FLANGE BEARING w/ COLLAR 3/16” LOWER PLATE3
33C5001303/8” LOCK WASHER3
34C5001293/8” NUT3
35C100108#40 x 139 PITCH CHAIN2
36C100109WATER DRUM PLUG1
37C100083SMALL STEEL WASHER2
38C100087SMALL RUBBER GASKET1
39C100086WATER DRUM 403
40C700010DRUM AXLE3
41C100084LARGE RUBBER GASKET2
42 43C700011 C200015INNER HALF-PLATE w/ STUDS #40 x 30 SPROCKET1

HANDLE & CONTROL ASSEMBLY

FIGURE 3

CLASSEN TA25DA Powersteer Aerator - CONTROL

ITEMPART NO.DESCRIPTIONQTY
1C300006.7FLAT, PIVOT2
2C500034WASHER, 1/2 FLAT5
3C500131NUT, 1/2-13 LOCK8
4C500149BOLT, 1/2-13 x 22
5C500043BOLT, 3/8-16 X 14
6C500042WASHER, 3/8″ FLAT3
7C500130WASHER, 3/8 LOCK6
8C500129NUT, 3/8-165
9C500041NUT, 3/8-16 LOCK12
10C500134BOLT, 3/8-16 x 1-1/42
11C500101NUT, 5/16-185
12C500169NUT, 5/16-18 LOCK10
13C500162BOLT, 3/8-16 X 6-1/21
14C100007GRIP, RUBBER2
15C100034SPRING, CLUTCH CABLE2
16C100035SPRING, THROTTLE1
17 18C100149 C400081.7CABLE W/ENDS, THROTTLE HANDLE, L.H. CONTROL1
19C400090.7HANDLE, R.H. CONTROL1
20C400088.7ARM, THROTTLE1
21C500079BOLT, 3/8-16 X 1-3/41
224174339LINKAGE ARM4
234174322UPPER HANDLE2
244174329LOWER HANDLE, MAIN1
254174323HANDLE, LIFT, TA251
26 274172652 C500154SPACER – 9/16 OD x 3/8 ID x 3/8 BOLT, 3/8-16 x 2-1/21
2894268-03NUT-FL NYLON LOCK2
2994262-014BLT-FLG HD2
304173160GRIP – 1″ X 10″4
31C400446SPACER, 5/16 X 22
324174340HANDLE BRACE SPLIT DRV1

Classen Warranty Statement

2-Year Limited Warranty
This Classen Product is warranted against defects in materials and workmanship for a period of two (2) years from the date of purchase from an authorized dealer under the following terms and conditions. Schiller Grounds Care’s responsibility under  this limited warranty is restricted to repairing or replacing, at its option, any covered part found to be defective in material or workmanship during the warranty period. All parts replaced under warranty will be considered as part of the original product and any warranty on the replaced parts will expire coincidentally with the original product warranty.
SCHILLER GROUNDS CARE, INC. MAKES NO EXPRESS OR IMPLIED WARRANTIES, REPRESENTATIONS, OR PROMISES EXCEPT THOSE CONTAINED HEREIN. THERE ARE NO OTHER WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALL WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH ABOVE ARE SPECIFICALLY DISCLAIMED. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE DURATION OF THIS WRITTEN LIMITED WARRANTY.
To Obtain Warranty Service – Warranty service must be performed by an authorized Classen dealer. To locate a dealer, please visit: www.classenturfcare.com and click on FIND A DEALER. For further assistance, write or email the Technical Services Department of Schiller Grounds Care
Schiller Grounds Care, Inc.
1028 Street Road
Southampton, PA 18966
techservicesupport@schillergc.com
ABOUT YOUR WARRANTY
The warranty period begins on the date of purchase by the original retail or commercial customer from an authorized Classen dealer and is not transferable. Warranty service must be performed by an authorized Classen dealer. If a warranty replacement becomes necessary, the authorized dealer must be prepared to provide the physical component for verification (freight prepaid) upon request from Schiller Grounds Care. Warranty service will be performed without charge to the original  purchaser for parts and labor. The original purchaser is responsible for the expense of delivering the equipment, part, oraccessory to and from an authorized dealer’s service center. The purchaser is responsible for any premium charged for overtime labor requested by the purchaser and for any service and/or maintenance not directly related to any defect covered under this limited warranty. Proof of purchase will be required to substantiate any warranty claim. Without proof of the initial purchase date from an authorized dealer, the manufacturing date of the product will be used to establish the warranty period.
EXCLUSIONS
This warranty only covers defects in materials or workmanship.
Engines and Other Manufacturers – Schiller Grounds Care makes no warranty with respect to engines or engine parts such as spark plugs, lubricants, starters, and carburetors. The engine warranty is covered by the engine manufacturer. Consult the Operator’s Manual for the engine provided with your product or ask an authorized dealer for the terms and conditions of these warranties. Schiller Grounds Care makes no warranty with respect to other parts not of its manufacture such as tires, batteries, gearboxes, or similar. These other parts may be covered by the warranties of their respective manufacturers. Wear Items – This limited warranty does not cover damages or defects from normal wear and tear. This limited warranty does not include routine maintenance and normal maintenance parts, including but not limited to tires, batteries, transmissions, clutches, filters, gearboxes, blades, tines, belts, chains, cables, or bearings.
Negligence and Improper Maintenance or Repair – This limited warranty does not cover any equipment that has been subject to lack of reasonable and proper maintenance, misuse, lack of proper storage, or accidents. This limited warranty does not cover any damage to the equipment that is caused by a freight carrier or is the result of failure to follow the operating instructions within the Owner’s Manual. This limited warranty does not cover any defects due to repairs, modifications, or alternations made to the product by anyone other than Schiller Grounds Care or its authorized dealers. In addition, this limited warranty does not cover repairs made necessary due to a lack of proper protection during storage. This limited warranty does not cover damage caused by the use of parts, supplies, or accessories, including, without limitation, filters, spark plugs, carburetors, ignition, drive belts, brakes, gasoline, fuel, oil, or lubricants, which in the reasonable judgment of Schiller Grounds Care, are either incompatible with the product, adversely affect its operation, performance, durability or are other than as recommended in the Operator’s Manual or other operational instructions provided by Schiller Grounds Care.
Improper Use – This limited warranty does not cover any Classen Product, part, or accessory that (i) has been subject to misuse, abuse, neglect, negligence, or accident, or that has not been assembled, operated, or maintained in accordance with the operating or maintenance instructions specified in the Operator’s Manual; or (ii) has been altered or modified so as to adversely affect its operation, performance or durability, or that has been altered or modified in ways not approved by Schiller Grounds Care. To the extent permitted by law, neither Schiller Grounds Care nor any company affiliated with it makes any warranties, representations, or promises as to the quality, performance, or freedom from defect of the Classen Product, part, or accessory covered by this limited warranty. The authorized dealer makes no warranty of its own and such dealer has no authority to make any representation, warranty, or promise on behalf of Schiller Ground Care or to modify the terms or limitations of this limited warranty in any way.
Other Exclusions – This limited warranty does not include reconditioned, refurbished, used, or demonstration equipment. This limited warranty excludes failures due to acts of nature beyond the manufacturer’s control.
Extended Warranty – Schiller Grounds Care disclaims responsibility for any separately purchased extended warranty. ALL WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH ABOVE ARE SPECIFICALLY DISCLAIMED.
THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE DURATION OF THIS WRITTEN LIMITED WARRANTY.
Disclaimer of Consequential Damage – Schiller Grounds Care disclaims any responsibility for incidental or consequential damages including, but not limited to, the expense for gasoline, the expense of delivering the product to an authorized service dealer, the expense of returning the product to the purchaser, mechanic’s travel time, telephone charges, rental of a like product during the repair timeframe, travel, loss of revenue, loss of time, or inconvenience. SCHILLER GROUNDS CARE, INC. DISCLAIMS ALL LIABILITY FOR INDIRECT, INCIDENTAL, AND/OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE USE OF THE CLASSEN PRODUCTS COVERED BY THIS LIMITED WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

MAY 2022

Documents / Resources

CLASSEN TA25DA Powersteer Aerator [pdf] User Manual
TA25DA Powersteer Aerator, TA25DA, Powersteer Aerator, Aerator

References

Leave a comment

Your email address will not be published. Required fields are marked *