Categories: Chy Firemate

Chy Firemate VEABT007 Module User Manual

Chy Firemate VEABT007 Module

Features

  • On-chip low power microcontroller
  • 128KB of In-system programmable flash
  • 8KB SRAM
  • On board crystal and PCB Antenna

Application

  • Mobile device accessories (Android/ iOS)
  • Wireless data communication
  • Remote sensors

Pin definition (from right to left)

Pin No. Description Pin Type Functions
1 BLE_RX Digital I/O UART RX
2 BLE_TX Digital I/O UART TX
3 WAKE_UP Output Digital I/O
4 STATUS Input Digital I/O
5 GND Digital I/O GND
6 V+ Digital I/O VDD
7 BLE_EN Digital I/O VDD Enable

How to use

  • Before sending any UART Command, “WAKE_UP 1 → 0” must be done by external MCU.
  • If the RF module is connected to Smart Devices (Android/ iOS), the pin STATUS will be logic “1” to inform external MCU.
  • Beacon
    • Send Command ‘R’ to send live measured data from external through Beacon.
    • This is default mode, and RF module send data only. Cannot receive any data.
  • BLE
    • Send Command ‘M’ to switch mode from Beacon to BLE.
    • After the mode switch successfully, the external MCU can receive data from Smartphone.
  • Receiver
    • Send Command ‘E’/’G’/’I’ to switch mode from Beacon to Receiver.
    • Only specific Beacon data can be received, and the external MCU receives the data from UART
  • Protocol:
    • UART Baud Rate: 115200, 8, N, 1
    • Commands
      ‘M’: Mode Switch
      External MCU →RF Module
      Starter Len OP S/N CK End
      # M (0D 0A)h

      External MCU RF Module

      Starter Len OP Indi CK End
      > M (0D 0A)h

      ‘I’:Scan Product Information of multiple products External MCU →RF Module

      Starter Len OP Filter1 Filter2 Filter3 Filter4 Filter5
      ‘#’ ‘I’
      Filter6 Filter7 Filter8 CK End
      (0D 0A)h

      External MCU RF Module

      Starter Len OP Beacon Data RSSI CK End
      ‘>’ ‘I’ (0D 0A)h

      ‘C’: Scan stop
      External MCU →RF Module

      Starter Len OP CK End
      ‘#’ ‘C’ (0D 0A)h

      External MCU RF Module

      Starter Len OP CK End
      ‘>’ ‘C’ (0D 0A)h

      ‘X’: Setting RF Module parameter External MCU →RF Module

      Starter Len OP Setting FP Prod. S/N Cal. Date Tx Power CK End
      # X (0D 0A)h

      External MCU RF Module

      Starter Len OP FP Prod SN Cal Date Tx Power BLE_Ver CK End
      > X (0D 0A)h

      ‘R’: Send Beacon data External MCU →RF Module

      Starter Len OP Beacon Data CK End
      ‘#’ ‘R’ (0D 0A)h

      External MCU RF Module

      Starter Len OP Indi CK End
      ‘>’ ‘R’ (0D 0A)h

      ‘E’: Scan beacon information of one product External MCU →RF Module

      Starter Len OP Product Code CK End
      ‘#’ ‘E’ (0D 0A)h

      External MCU RF Module

      Starter Len OP Beacon Data RSSI CK End
      ‘>’ ‘E’ (0D 0A)h

      ‘G’: Scan beacon information of all products External MCU →RF Module

      Starter Len OP CK End
      ‘#’ ‘G’ (0D 0A)h

      External MCU RF Module

      Starter Len OP Beacon Data RSSI CK End
      ‘>’ ‘G’ (0D 0A)h

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).

End Product Labeling

This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following:
“Contains FCC ID: VEABT007”

End Product Manual Information

The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 0.5cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 0.5 cm is maintained between the antenna and users. As long as the condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

Documents / Resources

Chy Firemate VEABT007 Module [pdf] User Manual
BT007, VEABT007, VEABT007 Module
Share

Recent Posts

LG OLED83C1 Smart LED TV User Guide

OLED83C1 Smart LED TV OLED83C1* *MFL71773112* (2103-REV00) www.lg.com AA 1 1 2 QU QU 21BUIGJOEFS6OJUF…

46 seconds ago

Rockpi Trading RK3328 Rock Pi E SBC Features Rockchip User Manual

RK3328 Rock Pi E SBC Features Rockchip ROCK Pi E User Manual ROCK Pi E…

1 min ago

Pure Resonance PTT1 Push To Talk Microphone User Manual

PTT1 Push To Talk Microphone INSTALLATION AND OPERATION MANUAL Caution: Please read this manual carefully…

3 mins ago

Cloudy Bay LCSL430SMXX 4 Head WiFi/BLE Ceiling Track Light Instruction Manual

LCSL430SMXX 4 Head WiFi/BLE Ceiling Track Light LCSL430SMXX Thank you for purchasing CloudyBay Smart LED…

4 mins ago

Clarke CHG1600 Hot Air Gun Instruction Manual

CHG1600 Hot Air Gun HOT AIR GUN MODEL NO: CHG1600 PART NO: 3400762 USER INSTRUCTIONS…

7 mins ago

CARSON 907342 FlixBus 2.4 GHz RC Electric Bus Instruction Manual

907342 FlixBus 2.4 GHz RC Electric Bus FlixBus 2.4 GHz 100% RTR (READY-TO-RUN) MODEL DE…

10 mins ago