onvis SMS2-OD Smart Motion Sensor

Mga detalye

• Product Name: Smart Motion Sensor SMS2-OD
• Compatibility: Thread and Apple Home Hub
• Features: Quick Start Guide, Motion Detection, Smart Home Integration
• Additional Requirements: Apple Home Hub Setting

Mga Instruksyon sa Paggamit sa Produkto

Setting Up the Smart Motion Sensor

1. Ensure you have an Apple Home Hub set up in your home.
2. Follow the Quick Start Guide provided with the sensor for initial setup.
3. Place the sensor in a strategic location where motion detection is required.
4. Connect the sensor to your Apple Home Hub following the instructions.

Using the Smart Motion Sensor
Once set up, the smart motion sensor will detect motion and trigger actions based on your smart home settings. You can adjust sensitivity and other settings through the Apple Home Hub interface.

Pag-troubleshoot
If you encounter any issues with the sensor, refer to the user manual for troubleshooting steps. Ensure the sensor is within range of the Apple Home Hub for proper functionality.

Mga tip

1. The CONNECTED hub is required to be a Thread HomeKit Hub.
   • iOS Home APP* Home Settings— Home Hubs & Bridges— choose the hub
   • Apple TV 4K A2843(3rd Cen), A2169(2nd Cen)
   • Apple HomePod (2nd Gen)
   • Apple HomePod mini
   • Apple TV 4K A2737(3rd Cen), A1842(1 Cen)
   • Apple HomePod (1st Gen)
   • Kontaka suporta@onvistech.com alang sa tabang.

DALI NGA PAGSUGOD GIYA

1. Insert the included 2 AA alkaline batteries and close the cover.
2. Siguruha nga ang Bluetooth sa imong iOS aparato naa.
3. Gamita ang Home app, o i-download ang libre nga Onvis Home App ug ablihi kini.
4. Tap “+” in the top right corner and scan the QR code on the SMS2-OD to add the accessory to your Apple Home system.
5. Set up a Thread Apple Home hub as the CONNECTED hub to enable BLE+Thread connection, remote control and notification.
6. For troubleshooting visit: https://www.onvistech.com/Support/9.html

Mubo nga sulat:

• Kung DILI magamit ang pag-scan sa QR code, mahimo nimong i-input ang SETUP code nga giimprinta sa label sa QR code.
• Kung ang app nag-aghat sa "Dili makadugang sa Onvis-XXXXXX", palihug i-reset ug idugang pag-usab ang aparato. Palihug itago ang QR code para magamit sa umaabot.
• Ang paggamit sa usa ka accessory nga makapahimo sa HomeKit nagkinahanglan sa mosunod nga mga permiso:
  • Mga setting> iCloud> iCloud Drive> Pag-on
  • Mga setting> iCloud> Keychain> Pag-on
  • Mga setting> Privacy> HomeKit> Onvis Home> Pag-on

Thread ug Apple Home Hub Setting

• Ang pagkontrol sa kini nga accessory nga gipagana sa HomeKit nga awtomatiko ug layo sa balay nanginahanglan usa ka HomePod, HomePod mini, o Apple TV nga gipahimutang ingon usa ka hub sa balay. Girekomenda nga mag-update ka sa pinakabag-o nga software ug operating system.
• To build an Apple Thread network, a Thread enabled Apple Home hub device is required to be the CONNECTED hub (seen in the Home app) in the Apple Home system. If you have multiple hubs, please turn off the Non-Thread hubs temporarily, then one Thread hub will automatically be assigned as the CONNECTED hub.
• You may find the instruction here: https://support.apple.com/en-us/HT207057

Pagpaila sa Produkto

• Onvis Smart Motion Sensor SMS2-OD is an Apple ecosystem compatible, Thread + BLE5.O enabled, battery powered multi-sensor: Motion, Bright/Dark. Temperature and Humidity. It keeps you updated of your home conditions, and offers sensor status for Apple Home automations. It is designed with an IP66 waterproof rating to easily adapt to outdoor use scenarios.

• Detect ONLY when needed, Active/lnactive controllable
• Adjustable nga pagkasensitibo
• Linkable with bright/dark condition
• Records of detection, activation/deactivation-

Ibalik ang Mga Setting sa Pabrika
Unscrew the battery compartment, press and hold the reset button for 5 seconds, Onvis SMS2-OD will be reset to factory settings after the LED flashing green-red-green-red lights.

Mga detalye

• Model: SMS2-OD
• Wireless connection: Thread+Bluetooth Low Energy 5.0
• Motion detection: meters, 100 0 (1603 ft, 100 0)
• Operating temperature: -IOC 45C (14 ‘VI 13 T)
• Operating humidity: 5%-95% RH
• Accuracy: Typical±0.3 C, Typical±5% RH
• Dimension: 3.3*3.3*1.7inch/84*84*43mm
• Pagbatok sa Tubig: IP66
• Usage: Indoor & outdoor
• Power: 2xAA Replaceable Alkaline Batteries
• Battery standby time: 4 years

Mga Instruksyon sa Pag-instalar

Direktang Paggamit
Place the SMS2-OD on a flat surface like a shelf, table or desk.
Installation with Stickers
Clean and dry the target surface, peel off the sticker cover and stick the device on the surface.

Pag-instalar nga adunay Holder

1. Screw the holder pedestal into the device.

Loosen the knob to adjust detection direction. Tighten the knob to fix the direction.

Walay Tubag

1. Palihug susiha ang lebel sa baterya. Siguroha nga ang lebel sa baterya dili ubos sa 5%.
2. If SMS2-OD is under BLE5.0 connection, the range is limited to BLE range only. So if BLE connection is poor, please consider setting up a Thread network for SMS2-OD for better connection.
3. If the connection of SMS2-OD and the Thread network is too weak, try putting a Thread router to improve the Thread connection.

Pag-update sa Firmware

1. A red dot on the SMS2-OD icon in the Onvis Home app means a newer firmware is available.
2. Tap the SMS2-OD icon to enter main page, and then tap the upper right to enter details.
3. Follow the app prompting to complete firmware update. Do not quit the app during firmware update. Wait about 20 seconds for SMS2-OD to reboot and reconnect.

FAQ

Why does the response slow down to 4-8 seconds?
The connection with the hub might have been switched to bluetooth. A reboot of the home hub
and device will restore the Thread connection.

Why did I fail to set up my Onvis Smart Motion Sensor SMS2-OD to Onvis Home app?

1. Siguroha nga ang Bluetooth gipagana sa imong iOS device.
2. Make sure your SMS2-OD is within connecting range of your iOS device.
3. Before setting up, reset the device by long pressing the reset button for about 5 seconds until the LED flashing green-red-green-red lights.
4. Scan the setup code on the device or instruction manual.
5. Kung ang app nag-aghat nga "dili makadugang sa aparato" pagkahuman sa pag-scan sa code sa pag-setup:
   • remove this SMS2-OD that was added before and close the app;
   • ibalik ang accessory sa mga setting sa pabrika;
   • idugang pag-usab ang accessory;
   • i-update ang firmware sa device ngadto sa pinakabag-o nga bersyon.

Mga Dokumento / Mga Kapanguhaan

onvis SMS2-OD Smart Motion Sensor [pdf] Manwal sa Gumagamit 2ARJH-SMS2-OD, 2ARJHSMS2OD, SMS2-OD Smart Motion Sensor, SMS2-OD, Smart Motion Sensor, Motion Sensor, Sensor

Mga pakisayran

• Manwal sa Gumagamit