Milesight VS370-915M Radar Human Presence Sensor

1. Packing List

The package contains the following items:

• VS370 Sensor
• Magnetic Bracket
• ER14505 Li-SOCl₂ Batteries
• Quick Start Guide
• Warranty Card

2. Hardware Introduction

The Milesight VS370-915M sensor features several key hardware components:

• 1/4-20UNC Bracket Hole: A standard threaded hole for mounting the sensor using compatible brackets.
• NFC Area: Located on the device, this area is used for configuration via NFC technology.
• Fresnel Lens: This lens is designed to focus the radar waves for optimal detection.
• Batteries Compartment: The enclosure where the ER14505 batteries are inserted.
• Reset Button: A physical button used for device reset operations.

The sensor supports connectivity and features such as OTA (Over-The-Air updates), D2D (Milesight's D2D protocol), and PIR (Passive Infrared) compatibility indication.

3. Button Description

The sensor's functions are controlled via its buttons and battery insertion/removal:

Note on Reboot: The provided table lists 'Remove the batteries' as the action for 'Reboot'. This is an unusual instruction for rebooting a device; typically, a short press of a reset button is used. The document explicitly states this action for reboot in this section.

4. Power Supply

The sensor is powered by two ER14505 Li-SOCl₂ batteries. The diagram illustrates the correct method for inserting these batteries into the compartment, ensuring the positive (+) and negative (-) terminals are aligned correctly.

5. Configuration

The Milesight VS370-915M can be configured using the "Milesight ToolBox" mobile application, available for both Android and iOS smartphones. Configuration can be performed via Bluetooth or NFC.

NFC Configuration:

1. Download and install the "Milesight ToolBox" App from your smartphone's app store. Ensure your smartphone supports NFC.
2. Enable the NFC function on your smartphone.
3. Open the "Milesight ToolBox" App. Place your smartphone's NFC area against the sensor's NFC area. The app will read or write data to the device, displaying a success prompt upon completion.
4. For enhanced security, it is strongly recommended to set a custom password for the device. The default password is '123456'.

Bluetooth Configuration:

1. Download and install the "Milesight ToolBox" App from your smartphone's app store. Ensure your smartphone supports Bluetooth.
2. Enable Bluetooth and location services on your smartphone.
3. Open the "Milesight ToolBox" App. Select the Bluetooth configuration method, search for the target device, and initiate a connection.
4. Enter the Bluetooth password to read or write device data. A success prompt will appear upon successful connection.
5. For enhanced security, it is strongly recommended to set a custom password for the device. The default password is '123456'.

6. Installation

Location: The sensor should be mounted on a wall at a height between 2.5 and 2.9 meters. Ceiling installation is not supported.

Installation Steps:

1. Step 1: Prepare the mounting surface and attach the bracket.
2. Step 2: Mount the sensor onto the bracket.
3. Step 3: Adjust the sensor's tilt angle to optimize detection coverage.
4. Step 4: Ensure the sensor is securely installed and positioned correctly.

Installation Notes:

• For optimal performance, install the device at a higher position and tilt it downwards. Adjust the tilt angle according to the specific environment to ensure the target is within the detection range.
• To avoid interference from reflections, do not point the device directly at smooth surfaces such as walls, metal, or glass at close range.
• To prevent potential interference between devices, avoid placing multiple sensors too close to each other, which could lead to overlapping detection zones.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.