Cut Control LED Outdoor Lamp

IP44 DE Cut Control LED sa gawas Lamp - lamp

IP44 DE Cut Control LED sa gawas Lamp -utdoo

Cut control
Mga panudlo aron magamit

  1. Push main cable through cable entry part of the wall bracket and ensure tight seal.
  2. Attach wall bracket. Pay attention of position „top“. Use the washer gaskets with rubberized face against to the wall bracket. Seal unused mounting holes.
  3. Establish ground connection and connect power lines.
  4. Hook light housing into notch of the wall bracket. Press luminaire to the wall bracket and tight set screws flush and evenly. Avoid pinched cables.
  5. Turn the protection cover of the sensor by 180° to the right.
  6. Time setting: adjust the lighting time with the timecontrol as requested between 5 seconds and 8 minutes.
  7. Lux setting: adjust the lux with the lux-control as requested between 10-2000 lux.
  8. Turn back the protection cover of the sensor by 180° to the left to protect the small adjusting wheels and to ensure the motion detection.

Light technology:

230V Power LED/2700K + 3000K
system performance:
2700K: 16,5 W/996 lm + 3000K: 16,5 W/1078 lm
IP44 DE Cut Control LED sa gawas Lamp - EEC EEC

Teknikal nga kasayuran:

naglihok nga voltage: 230V / 50Hz

IP44 DE Cut Control LED sa gawas Lamp - safety klase sa pagpanalipod
IP44 DE Cut Control LED sa gawas Lamp -clas safety class 1
IP44 DE Cut Control LED sa gawas Lamp - Luminai Luminaire is suitable for mounting on normal inflammable surfaces.
IP44 DE Cut Control LED sa gawas Lamp - conform conformity mark

  • detection range: 9 m max.
  • time setting: 5 sec – 8 min
  • anggulo sa pagkakita: 120°
  • light-control: 10-2000 lux
  • working temperature: -25° ~+45°C

Sensor information:

IP44 DE Cut Control LED sa gawas Lamp - sensor

Mubo nga sulat:
Please don’t adjust the two functional controllers too much. That is because the two functional controllers are connected to the components directly. There is a small stopper in each of the two components. When you adjust the controllers from start to end, the excessive turn will damage the stopper, and lead to the 360°non-stop turn around. Please consider that the adjust range limit is 270°. Factory setting: lux-control is max, time setting is min.

  • Unrest objects hinder the correct initial operation of the sensor.
  • In front of the detection area there should be no obstacles or unrest objects effecting detection.
  • Avoid an installation near air temperature alteration zones, such as: air condition, central heating, etc.

Pagmentinar:

This luminaire contains built-in LED lamps. The LED lamps can be replaced by IP44.de in case of a failure of the LED. In this case, please get in touch with your retailer.

Pag-atiman:

Regularly clean luminaire from dirt and deposits. Do not use a high pressure cleaner for cleaning. Please note care instructions at www.IP44.de.

Safety:

We point out that the electric connection of light fixtures has to be done by a certified installer. We assume no accountability for damages which are a result of non-appropriate mounting or application of the luminaire. Modifications on the luminaire will result in loss of warranty.

Cut control

Anschlussschema 3-adrig
wiring diagram 3-core

IP44 DE Cut Control LED sa gawas Lamp - cut control

cut control
Anschlussschema 4-adrig
wiring diagram 4-coreIP44 DE Cut Control LED sa gawas Lamp - cut controlj

[protektado sa email].
www.IP44.de

Mga Dokumento / Mga Kapanguhaan

IP44 DE Cut Control LED sa gawas Lamp [pdf] Mga instruksyon
Cut Control, LED Outdoor Lamp, Cut Control LED Outdoor Lamp, Outdoor Lamp, Lamp

Leave sa usa ka comment

Ang imong email address dili nga gipatik.