Categories: CANARM

CANARM 6691529997 Ceiling Fan Instruction Manual

NEED HELP?
Call or Email us first
Our service team is ready to answer your questions…
1-800-265-1833 (English) / 1-800-567-2513 (French)
IN CANADA – ressalescanad@ccocanarmna.ca – IN USA- ressalesusa@canarmna.ca
Monday — Friday8Am-5P pm

INSTALLATION INSTRUCATIONS
DOWNROD MOUNT SERIES

INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS READ ALL INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
INSTALLATION AND WIRING TO BE IN ACCORDANCE WITH CEC, NEC, LOCAL ELECTRICAL CODES and ANSI/NFPA 70. Consult a qualified electrician if you are not familiar with wiring.

TOOLS AND MATERIALS REQUIRED
– Philips Screw Driver
– Blade Screw Driver
– Step Ladder
– Wire Cutters
– Wiring supplies as required by electrical code.

NOTE: FOR OPTIMUM QUIETNESS, FULLY ASSEMBLE FAN AND RUN 24 HOURS
2555 Rue Bernard
Lefebvre Laval, Quebec
H7C 0A5
PH: (450) 665-2535
FX: (450) 665-0910
2157 Parkedale Ave.
Brockville, Ontario
K6V 5V6
PH: (613) 342-5424
FX: (613) 342-8437

SAFETY PRECAUTIONS

  1. Turn off power at the main electrical service box before starting the installation
  2. Electrical connections must comply with local code ordinances, national electrical codes, CEC, NEC, and ANSI/NFPA 70.
  3. Make sure the installation site you choose allows the fan blades to rotate freely without any obstructions.
  4. When mounting the fan on a ceiling outlet box, Use an approved (CSA for Canada and UL for the U.S.) ceiling fan box marked “FOR FAN SUPPORT”. Ensure the outlet box is securely installed in place such that it is able to support at least the fan weight.
  5. WARNING: To reduce the risk of fire, electric shock, or another personal injury, mount fan only on an outlet box or supporting system marked acceptable for fan support of 35 lbs (15,9 kg) or less and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
  6. Total Fan Weight For Reference: 52″approximate 7.0 kgs(15.44lbs).

WARNING

– To r reduce the risk of fire or electrical shock, ONLY use model CQ006 remote control for optional remote control adaptability.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.
– Mount floor or with the lowest moving parts at least 2.10 Meters (7 Feet) above grade level.
– DO NOT operate reversing switch while fan blades are in motion. Fan be turned off and rotating blades stopped, reverse chain pulled, the speed chain must be pulled again to start in the opposite direction.
– WARNING: TO REDUCE THE RISK OF INJURY TO PERSONS, ENSURE THE FAN LOWER COVER IS SECURELY ATTACHED TO THE FAN UPPER COVER BEFORE USE.

INSTRUCTIONS

The slide switch is for forwarding/reverse rotation.
In cold weather: Set to reverse rotation (clockwise). Airflow will be directed upward, circulating warm air.
In warm weather: Set to forward rotation (counter-clockwise). Airflow will be directed downward, circulating cold air.

REMOTE CONTROL

Install 9 V battery (not included). Operation buttons on the remote:
1 – Fan high speed
2 – Fan medium speed
3 – Fan low speed
0 – Fan off
– Ligh ton/off
– Light dimmer
*Hold down to increase or decrease the light.
The light has a memory function so the light will stay at the same brightness as the last time it was turned off.

ASSEMBLY DRAWING

  1. Wooden Joist
  2. Approved (CSA for Canada and UL for the U.S.) ceiling fan box (not provided)
  3. Ceiling
  4. J-Hook
  5. Rubber Gasket
  6. Screws & Lock Washers (set of 4)
  7. Mounting Bracket c/w Ground Wire
  8. Outlet Box Screws (not provided)
  9. Lock Pin
  10. Hemisphere Jam Screw
  11. Hemisphere
  12. Downrod c/w Ground Wire
  13. Ceiling Canopy
  14. Bolt
  15. Yoke Cover
  16. Motor Assembly
  17. Jam Screws
  18. Cotter Pin
  19. Flat Washer
  20. Light Kit
  21. Motor Screw & Lock Washer
  22. Blade

INSTALLATION

NOTE: All set screws must be checked and retightened where necessary, before and after installation.

  1. MOUNTING
    – Take out fan motor housing.
    – Remove cotter pin and bolt from a yoke.
    – Loosen jam screw-in yoke until it is flush with the inside surface.
    – Obtain downrod, canopy, and yoke cover.
    – Place downrod inside canopy and yoke cover.
    – Route wires exiting motor through yoke cover, canopy, and downrod.
    – Insert bolt through the hole in shaft and downrod. Be careful not to damage or cut the fan wires.
    – Tighten flat washer and bolt. Secure with a cotter pin through the hole at the end of the bolt.
    – Secure downrod in position by tightening jam screws. Slide the yoke covers down so it is flush with the motor housing.
  2. INSTALL MOUNTING BRACKET
    WARNING: To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To UL/CSA Listed Outlet Box Marked Acceptable for Fan Support And Use Mounting Screws Provided With The Outlet Box.
    – Install J-Hook through the center of the outlet box and into the wooden joist.
    – Secure mounting bracket and rubber gaskets to the outlet box.
    – Hang the safety cable onto the J-hook.
    – Hang fan on a temporary hook or mounting bracket.
  3. ELECTRICAL HOOK-UP
    – This fan is equipped with a remote control unit for controlling the fan speeds and a light kit.
    A. Setting the code on the hand-held remote and the receiver.

    – remove the battery cover on the hand-held remote (Press firmly below the arrow and slide the battery cover off).
    – set code switches to the desired position.
    – set the code switches to the same positions on the receiver asset on the remote.
    B.
    Make the following wire connections to the receiver unit (see fig. 5) using the wire nuts supplied.
    – connect the male and female plug from the filter and the receiver.
    – connect the GREEN fan wire to the BARE (ground) wire.
    – connect BLACK receiver unit wire to BLACK supply wire.
    – connect WHITE receiver unit wire to WHITE supply wire.
    – connect WHITE receiver unit wire (MOTOR N) to WHITE fan wire.
    – connect BLACK receiver unit wire (MOTOR L) to BLACK fan wire.
    – connect BLUE receiver unit wire (FOR LIGHT) to BLUE light wire.
    – After making the wire connections, ensure the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
    – Ensure the splices after being made should be turned upward and pushed carefully up into the outlet box. In Quebec, the installation of this product must be carried out by a qualified electrician.
    In Quebec, the installation of this product must be carried out by a qualified electrician.
    NOTE: Once ground wires are connected, carefully tuck all wires and wire nuts into the metal outlet box making sure that the wires are clear of the hemisphere and downrod when positioned in the mounting bracket.
    C – Push all connected wires up into the ceiling box.
    – Position the receiver into the canopy as shown direction.
  4. MOUNTING FAN ASSEMBLY
    – Place two screws and washers on the mounting plate (marked B on diagram) which correspond with slots in the canopy. Screw-in two turns.
    – Position canopy to mounting plate aligning slots to screws (marked B on diagram) then turn to lock.
    – Position and tighten the two screws and washers (marked A on diagram) then tighten the two screws (marked B on diagram).
  5. ENGAGE HEMISPHERE (Downrod Mount Only)
    – Carefully rotate fan assembly until groove in hemisphere locks over the tab of canopy assembly.
    WARNING: Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.
    NOTE: When installing the fan on a sloped ceiling, make a sure tab on the hanger bracket facing towards the top of the slope. Depending on the slope, a longer downrod may be required to prevent fan blades from hitting the ceiling.
  6. MOUNTING BLADES TO MOTOR
    – Insert the blade arm into the fan as shown.
    – Tighten the blade arm to the motor with the screw and lock washer as shown.
    – Slightly turn the blade after installation and repeat the same step for the other blades.
  7. LIGHT KITS
    DETACHABLE LIGHT KITS
    (Refer to one of the following light kits for your model)
    – Remove light kit screws and washers.
    – Connect polarized connectors of light kit to corresponding connectors found in the switch housing.
    WARNING:
    BE SURE TO TURN OFF POWER BEFORE INSTALLING
    – Carefully tuck electrical wires back into switch housing, align light kit with switch housing, and secure with three light kit screws and washers.
    WARNING: Ensure that all connections, set screws, and screws are securely tightened before the next step.
    To clean the fixture, turn off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth.

TROUBLESHOOTING SUGGESTIONS
TROUBLE

  1. The fan will not start
    – Check wiring connections to the fan.
    – Check fuses and circuit breakers.
    – Check wiring connections in the switch housing.
    CAUTION: Turn the power off for the last two items.
  2. Fan sounds noisy
    – Check to make sure that all screws in the motor housing are snug.
    – Check to make sure that blade bracket screws are tight.
    – Check to make sure that barrettes in switch housing are not rattling against the wall of the switch housing.
    – If fan has a light kit make sure switch housing screws and set screws are tight.
    – Some fan motors are sensitive to signals from solid-state variable controls. If the solid-state controller is used, change to an alternative control. (See a representative for a list of available controls.)
    – Allow a 24-hour break-in period to eliminate most noises.
  3. Fan wobbles
    – Check that all blades are screwed firmly into blade brackets. or shakes excessively.
    – Check that blade brackets are secured firmly to the motor.
    – Check the distance from tip of the blades to the ceiling.
    – Check the distance between blade tip to blade tip. All measurements should be equal. Loosen blade screws and position blade until even then re-tighten.
    – Check that the downrod hemisphere notch is engaged in the canopy.
    – Check to make sure that jam screws in the downrod are tightened.
    – Make sure canopy and mounting bracket are tightened securely to the wooden joist.
    – Make sure warpage has not occurred in wooden blades. If so, contact the customer service department for replacement parts.

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information
Unique Identifier: CANARMNA
Responsible Party
CanarmInc.
808 Commerce Park Drive, Ogdensburg, New York, USA 13669 1-800-267-4427
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

5 YEAR LIMITED WARRANTY

“Thank you” for purchasing our product. It is our policy to furnish you with high-quality products at a fair price. With proper installation, your fan should provide you with years of money-saving comfort.
This fan is guaranteed to be free from defects in workmanship and material for a period of five (5) years from the date of purchase. Within the first (1) year from the date of purchase, any defective product should be returned to your RETAIL OUTLET along with proof of purchase. For the balance of the warranty, four (4) years, the MOTOR WINDINGS ONLY shall be free of defects. We will correct such defects or replace the motor assembly at the ow option if the product is returned, FREIGHT PREPAID, to us. The returned fan must be accompanied by your proof of purchase and a cheque for 520.00 for handing and labor charges. AA costs of removing and re-installing the product we YOUR RESPONSIBILITY damage to any part as such by accident, misuse, improper installation or by affixing any accessories IS NOT covered by this warranty. As a result of varying climatic conditions in our area, this warranty does not cover any changes in finishes, including rusting, pitting, corroding, tarnishing or peeling. WARRANTY VOID: In cases of alteration, abuse, installation not in accordance with instructions or REMOVAL of the CSA Sticker.

Documents / Resources

CANARM 6691529997 Ceiling Fan [pdf] Instruction Manual
6691529997, Ceiling Fan, 6691529997 Ceiling Fan, Fan

Recent Posts

KAYOBA 017104 4-in-1 161 Parts Construction Set Instruction Manual

017104 4-in-1 161 Parts Construction Set Item no. 017104 Rätten till ändringar förbehålles. Vid eventuella…

45 seconds ago

KAYOBA 003153 Home Gym Exercise Machine Instruction Manual

003153 Home Gym Exercise Machine

2 mins ago

KAYOBA 003150 Spinning Bike Instruction Manual

003150 Spinning Bike

3 mins ago

Menuett 014466 Cordless Steam Iron Instruction Manual

014466 Cordless Steam Iron

4 mins ago

DAM DH422X Dehumidifier User Guide

DH422X Dehumidifier FR Veuillez lire attentivement le livret "Consignes de sécurité et d'utilisation" avant la…

4 mins ago

Kruger Matz KM0770 Wireless Controller Owner’s Manual

KM0770 Wireless Controller Wireless controller KM0770 NÁVOD K OBSLUZE CS BEDIENUNGSANLEITUNG DE OWNER'S MANUAL EN…

5 mins ago