Campfire Audio ORBIT
Regulations and Operations Manual
2AS58-01 Orbit UI Earbuds with Charger Case
Regulatory Compliance Information
EU / UK Compliance
Campfire Audio hereby declares that this wireless device is in compliance with Directive 2014/53/EU and Radio Equipment Regulations 2017. A copy of the Declaration of Conformity is available at campfireaudio.com/compliance.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
FCC ID: 2AS58-01
ISED Statement
This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canadian radiation exposure limits set forth for an uncontrolled environment.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used installed and operated with a minimum distance of 0mm between the radiator and your body.
Operations: Orbit UI
| Function | Operation | Use Function Results | |
| 1 | First-time Bluetooth Pairing | Put the left and right earphones into the charging box to charge, open the cap of the charging box, and press and hold the reset button for 3 seconds to enter the Bluetooth pairing mode. Then open phone settings > Bluetooth devices > refresh devices and select “CAMPFIRE” | Left and right earphone lights flash alternately, indicator lights will go out after successful pairing. Pairing mode: all 4 LEDs will flash 3 times simultaneously. |
| 2 | ON | 1. Open the upper cover of the charging box and auto turn on the device and enter the automatic connection. 2. Press and hold the left and right earphones for 5 sec to shut down w/ earphones outside of the charging box | Power on prompt tone: “ON” |
| 3 | OFF | 1. Place earphones into the charging box and close the cap to automatically turn off 2. Long press the left and right earphones for 5s to shut down 3. Earphones will auto shut down after 10m without pairing 4. Earphones will turn off from low battery | Power off prompt tone: “OFF” |
| 4 | Rest | Long press the charging box for Los | |
| 5 | Auto re-connect | 1. Open the charging box cover 2. Earphones will connect to the last connected device | |
| 6 | Long-distance connection and automatic return connection | After disconnecting beyond the use distance range, the headset will auto-reconnect when back within range unless 10m has passed and earphones have turned off. | |
| 7 | Bluetooth Disconnected | 1. Auto disconnect when out of range 2.Manual disconnect/tum-off 3. Mobile phone is disconnected or has Bluetooth turned off | |
| 8 | Play and Pause Music | In the playback state, tap once on either earphone to play or pause music. |
| 9 | Previous song | Double-tap the left earphone | |
| 10 | Next song | Double-tap the right earphone | |
| 11 | Volume + | Long press the Right earphone and hold to continuously increase the volume | |
| 12 | Volume – | Long press the Left earphone and hold to continuously increase the volume | |
| 13 | Voice Assistant activation | Triple tap Left or Right earphone to wake up the voice assistant (Siri) | |
| 14 | Answer Call | Single-tap either earphone during an incoming call | |
| 15 | Hang up | During the call, single-tap either earphones | |
| 16 | Reject the call | Double-tap either earphone during an incoming call | |
| 17 | DUT mode | When the left and right earphones are paired double-tap the MFB button | |
| 18 | Charging box battery indicator | Open the cover of the charging box or click the button charging box to display the battery level | One light – 25% Two light – 50% Three light – 75% Four light – 100% |
| 19 | ‘Phone battery display | The earphone battery level and Bluetooth connection will be displayed on (the phone | |
| 20 | iPhone Volume sync | The volume of the earphones is synchronized with the volume of the mobile phone | |
| 21 | Charging box battery indicator | Open the cover of the charging box and press the button to display the battery level of the charging box | |
| 22 | Earphone charging | Place earphones in the charging box and close the cover. The device will disconnect after 3 seconds. One earphone can be placed in the charging box without affecting the use of the single earphone. | |
| 23 | Bluetooth pairing | Long press the charging box for 3s | Indicator lights will flash in a marquee pattern |
| 24 | reset | Long press the charging box for us to restore factory settings |
Documents / Resources
 | Campfire Audio 2AS58-01 Orbit UI Earbuds with Charger Case [pdf] User Manual 01, 2AS58-01, 2AS5801, Orbit UI Earbuds with Charger Case, 2AS58-01 Orbit UI Earbuds with Charger Case |
