KRAMER VW-4 4 HDMI Output Cascading Video Wall Driver
Comprova què hi ha a la caixa
- VW-4 4 Output Video-Wall Driver
- 1 adaptador de corrent i cable
- 1 joc de suports
- 4 peus de goma
- 1 Guia d'inici ràpid
Get to know your VW-4
| # | característica | function |
| 1 | LED ON | S'il·lumina verd quan el dispositiu està encès. |
| 2 | LED D'ENTRADA | Lights green when a valid input signal is detected on the input. |
| 3 | OUTPUT LEDs (1 to 4) | Light green when an acceptor is detected on that output. |
| 4 | INPUT HDMI Connector | Connecteu-vos a una font HDMI. |
| 5 | LOOP HDMI Connector | Connect to an additional VW-4 device for configuring a large video wall or to a local monitor. |
| 6 | SERVICE USB Port | Use to perform firmware upgrade. |
| 7 | OUT HDMI Connectors (1 to 4) | Connect to up to 4 HDMI acceptors that make up the video wall configuration. The appropriate segments of the zoomed picture are output on these connectors for connection to the displays in the video-wall.
The output on these connectors is at 1080P resolution. |
| 8 | CONFIGURACIÓ DIP-interruptor de 4 vies | For fast, basic configuration of the device without needing to be connected to a PC, see Pas 6: Configure VW-4. |
| 9 | RS-232 3-pin terminal block connector | Use to setup and monitor the VW-4 via the Windows software and to upgrade the firmware. |
| 10 | Connector ETHERNET RJ-45 | Connect to a PC via a LAN to setup and monitor the VW-4 via the configuration app. |
| 11 | Connector de 5V CC | Connecteu-vos a l'adaptador d'alimentació subministrat. |
Mount VW-4
Install VW-4 using one of the following methods:
- Col·loqueu els peus de goma i col·loqueu la unitat sobre una superfície plana.
- Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/VW-4)..
- Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/VW-4).
PERILL
- Assegureu-vos que l’entorn (per exemple, temperatura ambiental màxima i flux d’aire) sigui compatible amb el dispositiu.
- Eviteu la càrrega mecànica desigual.
- S’ha d’utilitzar la consideració adequada de les qualificacions de la placa d’identificació de l’equip per evitar la sobrecàrrega dels circuits.
- Cal mantenir una connexió a terra fiable dels equips muntats en bastidor.
- L'alçada màxima de muntatge del dispositiu és de 2 metres.
Connecteu entrades i sortides
The three devices in this 6×2 diagram are designated 0, 1 and 2. Each output is designated by the device number and its outputs. For example, VW-4 (1) is the second device in this video wall configuration and VW-4 (1-2) is HDMI OUT 2 on that device. 
Connecta l’alimentació
Connect the power adapter to VW-4 and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution:
- Per als productes amb terminals de relé i ports GPI \ O, consulteu la classificació permesa per a una connexió externa, situada al costat del terminal o al Manual d'usuari.
- No hi ha peces reparables per l’operador a l’interior de la unitat.
advertència
- Utilitzeu només el cable d'alimentació que es subministra amb la unitat.
- Desconnecteu l’alimentació i desconnecteu la unitat de la paret abans d’instal·lar-la.
Configure VW-4
Configure VW-4 via
- DIP-switch settings – for basic video wall configuration.
- VW-4 app, via the Ethernet or RS-232.
- De manera remota, mitjançant ordres sèrie RS-232 transmeses per un sistema de pantalla tàctil, PC o un altre controlador sèrie.
Control RS-232 / Protocol 3000 Velocitat de transmissió: 115,200 Paritat: cap Bits de dades: 8 Format de l'ordre: ASCII Bits d'aturada: 1 Example: (Set Auto-sync Off to Fast): #SCLR-AS 1,2 Paràmetres Ethernet per defecte Adreça IP: 192.168.1.39 Passarel·la: 192.168.0.1 Màscara de subxarxa: 255.255.0.0 Port TCP #: 5000
Video Wall Configuration via DIP-switch Settings
You can use the DIP-switch settings to quickly configure a basic video wall (without bezel correction) of up to 4×4, consisting of 1 or more VW-4 devices.
When the video wall size is configured using the DIP-switches, it is not possible to set it up via the configuration app. (To use the app, make sure that the DIP-switches are all OFF).
| DIP 1 | DIP 2 | DIP 3 | DIP 4 | Columns x Rows Layout | notes |
| OFF | OFF | OFF | OFF | Basic setup is not used (default) | |
| OFF | OFF | OFF | ON | Full size picture (“1×1” wall) | Image appears on all displays. |
| OFF | OFF | ON | OFF | N / A | |
| OFF | OFF | ON | ON | N / A | |
| Un VW-4 Aparell | |||||
| OFF | ON | OFF | OFF | 2×2 wall (0) | |
| OFF | ON | OFF | ON | 4×1 wall (0) | |
| OFF | ON | ON | OFF | 1×4 wall (0) | |
| OFF | ON | ON | ON | N / A | |
| Tres VW-4 Dispositius | |||||
| ON | OFF | OFF | OFF | 3×3 wall, first unit (0) | |
| ON | OFF | OFF | ON | 3×3 wall, second unit (1) | |
| ON | OFF | ON | OFF | 3×3 wall, third unit (2) | |
| ON | OFF | ON | ON | N / A | |
| Quatre VW-4 Dispositius | |||||
| ON | ON | OFF | OFF | 4×4 wall, first unit (0) | |
| ON | ON | OFF | ON | 4×4 wall, second unit (1) | |
| ON | ON | ON | OFF | 4×4 wall, third unit (2) | |
| ON | ON | ON | ON | 4×4 wall, fourth unit (3) | |
Video Wall Configuration via the configuration app
Use the VW-4 Windows® Control Software app to configure a video wall of up to 8×8, consisting of 1 or more VW-4 devices (see www.kramerav.com/product/VW-4#Tab_Resources).
To configure the video wall (for example, a 3×2 video wall, using 2 devices)
- 1. Download the latest VW-4 Control Software app from www.kramerav.com/product/VW-4#Tab_Resources.
- Obriu l'aplicació.
- Feu clic a Connexió.
The Connection window opens, showing a list of all the connected VW-4 devices and the available RS-232 ports on your PC. The Connection window opens.
- Select a device under All Units and click . The selected device moves to the Selected Units area.
- Add the other connected devices.
- Feu clic a Acceptar.
- Select the Settings tab and then select the Output tab.
- If you need to change the device ID, enter the new ID under ID-NAME and press Enter on your keyboard.
You can set the ID number individually only when the device is directly connected to your PC. The ID number is set to each device, and according to that number each device is assigned its physical position in the video wall setup. - View the sink status of each device output and:
- Set OSD Info.
- Define Auto-Sync Off status.
- Set the HDCP per output and click Save.
- Seleccioneu la pestanya Disseny.
- Set the video wall size by either:
- Selecting Column and Row numbers (for example, 3 x 2). OR
- Clicking Quick Selection for common video wall configurations.
- Select horizontal and vertical bezel corrections (in pixels).
For each connected device, VW-4 App also enables performing factory reset, upgrading the firmware, viewing network settings and copying the EDID to the input from a selected EDID source.
Documents/Recursos
 |
KRAMER VW-4 4 HDMI Output Cascading Video Wall Driver [pdf] Guia d'usuari VW-4, 4 HDMI Output Cascading Video Wall Driver, VW-4 4 HDMI Output Cascading Video Wall Driver, Video Wall Driver, Wall Driver, Driver |
