User Manual for LEDYI Lighting models including: V1-K, Rotary LED Dimmer
Rotary LED Dimmer Model No.: V1-K. Rotary dimming/Numeric display/Max 20A/Four PWM frequency/Linear or logarithmic dimming/Multiple protection View
Rotary LED Dimmer Model No.: V1-K. Rotary dimming/Numeric display/Max 20A/Four PWM frequency/Linear or logarithmic dimming/Multiple protection.
prieš 2 dienas — User Manual Ver 1.1.0. Operation temperature. Case temperature (Max.) Environment. IP rating. Technical Parameters. Output power. 240W/480W Max.
Rotary LED Dimmer Model No.: V1-K Rotary dimming/Numeric display/Max 20A/Four PWM frequency/Linear or logarithmic dimming/Multiple protection Features Rotary dimmer with digital numeric display, visible dimming level. Match with RF 2.4G single zone or multiple zone dimming remote control optional. 0-100% dimming smoothly without any ash. High load current up to 20A. Logarithmic or linear dimming curve selectable. PWM frequency 500Hz, 2kHz, 8kHz or 16kHz selectable. Over-heat / Over-load / Short circuit protection, recover automatically. Light on/off fade time 3s selectable. Technical Parameters Input and Output Input voltage Input current Output voltage Output current Output power Output type 12-24VDC 20A 12-24VDC 1CH,20A Max. 240W/480W Max. @ (12V/24V) 500Hz PWM Constant voltage Dimming data Input signal Control distance Dimming gray scale Dimming range Dimming curve PWM Frequency Rotary knob + RF 2.4GHz 15m(Barrier-free space) 100 levels 0 -100% Logarithmic or linear 500Hz, 2kHz, 8kHz, 16kHz Safety and EMC EMC standard (EMC) Safety standard(LVD) Radio Equipment(RED) Certification ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED Environment Operation temperature Case temperature (Max.) IP rating Ta: -30 OC ~ +55 OC T c: +85OC IP20 Warranty and Protection Warranty 5 years Protection Reverse polarity Over-heat Over-load Short circuit User Manual Ver 1.1.0 Mechanical Structures and Installations Digital display Match key Rotary switch % OFF ON DC12-24V 20A Max. IN OUT VV V1-K Rotary LED Dimmer LED indicator Installation rack Dip switch setting LED output LED output + Power input + Power input - VV 107.00 mm 75.00 mm OFF ON Wiring Diagram 38.00 mm 75.00 mm 24.50 mm V1-K % OFF ON DC12-24V 20A Max. IN VV OUT VV Single color LED strip + Power Supply 12-24VDC Constant Voltage AC100-240V Page 1 Match Remote Control (two match ways) End user can choose the suitable match/delete ways. Two options are offered for selection: Use Match key Match: Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. The LED indicator fast flash a few times means match is successful. Delete: Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted. Use Power Restart Match: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. .Delete: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. PWM frequency setting 16KHz 8KHz 2KHz 500Hz 10A 10A 15A 20A 12 12 12 12 We can select four PWM frequency: 500Hz, 2kHz, 8kHz or 16kHz. Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video). Dimming curve setting PPW WMM dduuttyy((%%)) PWM duty(%) Linear dimming curve 110000 9900 8800 7700 6600 5500 4400 3300 2200 1100 Gamma=1.0 10 20 30 40 50 60 70 80 90 100 Brightness(%) 3 Logarithmic dimming curve 100 Gamma=1.6 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) 3 User Manual Ver 1.1.0 Light on/off fade time Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s. V1-K Rotary LED Dimmer Malfunctions Analysis & Troubleshooting Malfunctions No light Uneven intensity between front and rear,with voltage drop Causes 1. No power. 2. Wrong connection or insecure. 1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability. Troubleshooting 1. Check the power. 2. Check the connection. 1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater. Page 2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6