Riokko YM119 OBD2 Scanner Color Screen Code Reader Instruction Manual

1. Uvod

Thank you for choosing the Riokko YM119 OBD2 Scanner. This device is designed to assist vehicle owners and technicians in diagnosing engine-related issues by reading and clearing diagnostic trouble codes (DTCs), viewing live data, and performing various diagnostic tests on OBDII/EOBD compliant vehicles manufactured since 1996.

The YM119 provides a user-friendly interface with a color screen, making vehicle diagnostics accessible and efficient. This manual will guide you through the setup, operation, maintenance, and troubleshooting of your new scanner.

Ključne karakteristike:

• Engine Fault Diagnosis (Read/Clear DTCs)
• Live Data Stream Display
• Zamrzni okvir podataka Viewing
• I/M Readiness Status Check
• Test O2 senzora
• Test ugrađenog monitora
• Test komponenata
• Vehicle Information Retrieval (VIN, CIN, CVN)
• Biblioteka za pretragu DTC-a
• Battery Voltage Test

2. Sigurnosne informacije

Always read and understand all safety messages and instructions in this manual before operating the scanner. Failure to do so may result in injury or damage to the scanner or vehicle.

• Sigurnost vozila: Always perform automotive testing in a safe environment. Do not wear loose clothing or jewelry when working on an engine. Keep hair, clothing, hands, tools, and test equipment away from all moving or hot engine parts.
• električna sigurnost: The vehicle's battery can produce explosive gases. Keep sparks, open flames, and smoking materials away from the battery. Always wear eye protection and appropriate clothing when working near the battery.
• ventilacija: Ensure the work area is well-ventilated. Exhaust fumes contain carbon monoxide, a poisonous gas.
• Paljenje: Do not connect or disconnect test equipment with the ignition on or engine running, unless specifically instructed to do so by the manual.
• Napajanje: The scanner is powered directly from the vehicle's OBDII port. Ensure the vehicle's battery is adequately charged before performing diagnostics.

3. Proizvod je gotovview

The Riokko YM119 OBD2 Scanner features a compact design with a color display and intuitive button layout for easy navigation and operation.

Figure 3.1: Riokko YM119 OBD2 Scanner. This image shows the front view of the blue scanner unit, highlighting its color screen with menu icons (Diagnosis, Battery, DTC Lib, Setting) and the array of control buttons (EXIT, UP, BAT, LEFT, OK, RIGHT, DOWN) below the screen. The attached OBDII cable and connector are also visible.

Scanner Components:

• Ekran u boji: Displays menu options, diagnostic data, and results.
• OBDII konektorski kabel: Connects the scanner to the vehicle's OBDII port.
• Navigacijski gumbi:
  • Dugme OK: Potvrđuje izbor ili ulazi u meni.
  • Dugme EXIT: Vraća na prethodni ekran ili izlazi iz funkcije.
  • GORE/DOLJE tipke: Scrolls through menu options or data.
  • LIJEVO/DESNO tipke: Moves cursor or changes values (if applicable).
  • Dugme BAT: Quickly accesses the battery test function.

Figure 3.2: Professional OBDII Scanner Features. This diagram illustrates the various diagnostic capabilities of the Riokko YM119 scanner, including Engine Fault Diagnostics, Quick Clear Fault Code, Estimate Battery Life Test, Real-time Data Stream, Free Frame Record Information, I/M Read Status, Oxygen Sensor Monitoring Results, Vehicle Identification Number, and Diagnostic Trouble Code Library.

4. Podešavanje

The Riokko YM119 scanner is designed for quick and easy setup. No batteries are required as it draws power directly from the vehicle's OBDII port.

Povezivanje skenera:

1. Locate the vehicle's 16-pin Data Link Connector (DLC). The DLC is usually located under the dashboard on the driver's side. Refer to your vehicle's service manual for the exact location if you cannot find it.
2. Turn the vehicle's ignition to the OFF position.
3. Firmly plug the scanner's OBDII connector into the vehicle's DLC.
4. Turn the vehicle's ignition to the ON position (engine off). The scanner will automatically power on and display the main menu.

Note: If the scanner does not power on, ensure the connection is secure and check the vehicle's fuse for the OBDII port.

5. Uputstvo za upotrebu

Once the scanner is connected and powered on, you can navigate through the main menu using the UP, DOWN, LEFT, RIGHT, OK, and EXIT buttons.

Figure 5.1: OBD II Diagnostic Test Items. This image displays the scanner's menu, showing various diagnostic options such as Read Codes, Erase Codes, View Freeze Frame, I/M Readiness, Vehicle Information, Live PCM Data, Realtime Curve, O2 Sensor Test, On-board Mon. Test, and Component Test.

5.1. Diagnosis Menu

From the main menu, select 'Diagnosis' and press OK to enter the diagnostic functions.

• Pročitajte kodove:

  This function reads the Diagnostic Trouble Codes (DTCs) stored in the vehicle's Engine Control Unit (ECU). These codes indicate specific issues detected by the vehicle's onboard diagnostic system.

  1. Select 'Read Codes' and press OK.
  2. The scanner will display any stored Pending, Confirmed, or Permanent DTCs.
  3. Use UP/DOWN to scroll through codes if multiple are present.
• Obriši kodove:

  This function clears all stored DTCs from the vehicle's ECU and turns off the Malfunction Indicator Lamp (MIL), poznata i kao lampica za provjeru motora. Warning: Clearing codes does not fix the underlying problem. Ensure the issue is resolved before clearing codes, or the light will likely return.

  

  Figure 5.2: Check and Turn Off Engine Light. This image demonstrates the scanner's ability to diagnose and clear the engine fault light, showing a dashboard with the engine light illuminated before diagnosis and off after the fault is cleared.

  1. Select 'Erase Codes' and press OK.
  2. Potvrdite svoj izbor kada se to od vas zatraži.
  3. The MIL will turn off, and DTCs will be cleared.
• View Zamrzni okvir:

  Freeze Frame Data is a snapshot of sensor values recorded by the ECU at the moment a DTC was set. This data can help identify the conditions under which the fault occurred.

  

  Slika 5.3: View Freeze Frame and DTCs. This image shows the scanner's display for Freeze Frame data, including parameters like LOAD_PCT, ECT, MAP, RPM, VSS, and MAF, along with a section for 'Since DTCs Cleared' showing monitor status.

  1. Odaberite 'View Freeze Frame' and press OK.
  2. The scanner will display the recorded parameters. Use UP/DOWN to scroll.
• I/M spremnost:

  I/M Readiness (Inspection/Maintenance Readiness) indicates whether the various emissions-related systems on the vehicle are operating correctly and have completed their self-tests. This is crucial for emissions testing.

  1. Select 'I/M Readiness' and press OK.
  2. The scanner will display the status of various monitors (e.g., Misfire Monitor, Fuel System Monitor, Catalyst Monitor) as 'OK' (complete) or 'INC' (incomplete).
• Live PCM Data:

  This function displays real-time operational parameters from the vehicle's Powertrain Control Module (PCM). This data can be viewed as numerical values or graphical curves.

  

  Figure 5.4: Real-time Data Stream. This image shows the scanner displaying live PCM data, with multiple parameters listed numerically and a section for 'Realtime Curve' indicating graphical representation of data.

  1. Select 'Live PCM Data' and press OK.
  2. Choose 'View Data' for numerical values or 'Graph Data' for graphical representation (if available for the parameter).
  3. Use UP/DOWN to scroll through parameters.
• Podaci o vozilu:

  Retrieves vehicle information such as Vehicle Identification Number (VIN), Calibration ID (CIN), and Calibration Verification Number (CVN).

  1. Select 'Vehicle Information' and press OK.
  2. The scanner will display the available information.
• Test O2 senzora:

  Monitors the results of oxygen sensor tests.

  1. Select 'O2 Sensor Test' and press OK.
  2. View rezultate testa.
• Test ugrađenog monitora:

  Dohvaća rezultate ispitivanja komponenti i sistema pogonskog sklopa povezanih s emisijama koje se ne prate kontinuirano.

  1. Select 'On-Board Mon. Test' and press OK.
  2. View rezultate testa.
• Test komponente:

  Allows for testing of specific components or systems by initiating an on-demand test.

  1. Select 'Component Test' and press OK.
  2. Follow on-screen prompts to perform the test.

5.2. Test baterije

The YM119 can perform a quick test of the vehicle's battery voltage.

Figure 5.5: Estimate Battery Life Test. This image shows a hand interacting with the scanner, which displays the 'Battery' menu option, indicating the scanner's capability to monitor battery life and understand battery index.

1. From the main menu, select 'Battery' or press the 'BAT' button.
2. Skener će prikazati trenutni nivo napunjenosti baterijetage.

5.3. DTC Lib (DTC Library)

This function allows you to look up the definition of a Diagnostic Trouble Code (DTC).

1. From the main menu, select 'DTC Lib' and press OK.
2. Enter the DTC using the navigation buttons (UP/DOWN for numbers, LEFT/RIGHT to move cursor).
3. Pritisnite OK za view definicija koda.

5.4. Podešavanje

The 'Setting' menu allows you to customize various scanner preferences.

• Jezik: Promijenite jezik prikaza.
• jedinice: Prebacivanje između metričkih i imperijalnih jedinica za prikaz podataka.
• Zvučni signal: Turn the button press sound on or off.
• O: View scanner information such as software version.

6. Održavanje

Proper care and maintenance will ensure the longevity and reliable operation of your Riokko YM119 scanner.

• čišćenje: Koristite meku, damp krpu za čišćenje vanjštine skenera. Ne koristite abrazivna sredstva za čišćenje ili rastvarače.
• Skladištenje: Store the scanner in a clean, dry environment away from extreme temperatures, direct sunlight, and excessive dust. Keep it in its original packaging or a protective case when not in use.
• Održavanje kablova: Do not pull on the cable to disconnect the scanner from the vehicle. Always grasp the connector firmly. Avoid kinking or bending the cable excessively.
• Ažuriranja softvera: This model typically does not require user-performed software updates. If an update becomes available, it would be provided by the manufacturer with specific instructions.

7. Otkrivanje problema

If you encounter issues with your Riokko YM119 scanner, refer to the following common problems and solutions:

If the problem persists after trying these solutions, please contact Riokko customer support for further assistance.

8. Specifikacije

9. Jamstvo i podrška

Riokko products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Riokko website.

Korisnička podrška:

If you have any questions, require technical assistance, or need to report an issue with your Riokko YM119 scanner, please contact Riokko customer support through their official website or the contact information provided with your purchase. Please have your model number (YM119) and purchase details ready when contacting support.