AeroCool Mirage L240 ARGB Uputstvo za upotrebu tečnog hlađenja

Uvod

The AeroCool Mirage L240 ARGB Liquid Cooler is a high-performance all-in-one (AIO) liquid cooling solution designed for efficient heat dissipation from your CPU. Featuring a 240mm radiator, two 120mm Addressable RGB (ARGB) fans, and a unique infinity mirror pump design, it provides both superior cooling capabilities and stunning visual effects for your PC build. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your cooler.

Figure 1: AeroCool Mirage L240 ARGB Liquid Cooler with its vibrant ARGB fans and pump.

Šta je u kutiji

Molimo Vas da provjerite da li su sve komponente prisutne prije početka instalacije.

• AeroCool Mirage L240 ARGB Liquid Cooler (Radiator, Pump, and Tubing pre-assembled)
• 2 x 120mm ARGB ventilatora
• Komplet hardvera za montažu (za Intel i AMD sockete)
• Vijci za montažu ventilatora i hladnjaka
• Termalna pasta (unaprijed nanesena ili u tubi)
• ARGB Controller (if not motherboard sync compatible)
• Korisnički priručnik (ovaj dokument)

Note: The provided product information only listed "Camera body" for "whats_in_the_box". This is a generic list for a liquid cooler.

Specifikacije

Postavljanje i instalacija

Follow these steps carefully to install your AeroCool Mirage L240 ARGB Liquid Cooler.

1. Pripremite svoj sistem

• Isključite računar i iskopčajte ga iz zidne utičnice.
• Otvorite kućište računara i uklonite postojeći hladnjak procesora.
• Clean the CPU surface thoroughly with isopropyl alcohol to remove old thermal paste.

2. Ugradite radijator i ventilatore

1. Attach the two 120mm ARGB fans to the radiator using the long fan screws provided. Ensure the fan airflow direction is as desired (typically exhaust out of the case or intake into the case).
2. Mount the radiator assembly to an available 240mm fan mount location in your PC case (e.g., top, front, or rear). Use the shorter radiator screws to secure it.

Figure 2: Radiator and fans assembled, ready for mounting in the PC case.

3. Install CPU Pump/Cold Plate

1. Select the appropriate mounting brackets for your CPU socket (Intel or AMD) from the hardware kit. Attach them to the pump unit.
2. If thermal paste is not pre-applied, apply a small pea-sized amount to the center of your CPU's integrated heat spreader (IHS).
3. Carefully place the pump/cold plate assembly onto the CPU, aligning the mounting holes.
4. Secure the pump to the motherboard using the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Figure 3: The copper cold plate of the pump unit, which makes contact with the CPU.

4. Povežite kablove

• Connect the pump's 3-pin power cable to the "CPU_FAN" or "AIO_PUMP" header on your motherboard.
• Connect each fan's 4-pin PWM cable to available fan headers on your motherboard (e.g., "SYS_FAN").
• Connect the ARGB cables from the fans and pump to your motherboard's 3-pin 5V ARGB header or to the included ARGB controller. Ensure correct polarity to avoid damage.
• Organize cables for good airflow and aesthetics.

Uputstvo za upotrebu

Once installed, the AeroCool Mirage L240 ARGB Liquid Cooler operates automatically based on your motherboard's fan control settings. The pump runs continuously to circulate coolant, and fan speeds adjust according to CPU temperature.

ARGB kontrola rasvjete

• Sinhronizacija matične ploče: If connected to a compatible motherboard ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync).
• ARGB kontroler: If using the included ARGB controller (if applicable), refer to its specific instructions for changing lighting modes, colors, and brightness.

Održavanje

Redovno održavanje pomaže u osiguravanju dugotrajnosti i optimalnih performansi vašeg hladnjaka tekućine.

• Čišćenje prašine: Periodically (every 3-6 months, or more often in dusty environments) power off your PC and use compressed air to clean dust from the radiator fins and fan blades. This prevents airflow restriction and maintains cooling efficiency.
• Vizuelni pregled: Check the tubing and connections for any signs of leaks or damage. While rare, early detection can prevent issues.
• Rad ventilatora: Ensure all fans are spinning freely and quietly. Replace any fans that become noisy or stop working.

Figure 4: Regularly clean dust from the radiator and fan blades for optimal performance.

Rješavanje problema

If you encounter issues with your AeroCool Mirage L240 ARGB Liquid Cooler, refer to the following common problems and solutions.

Garancija i podrška

AeroCool products are designed for reliability and performance. For warranty information, technical support, or to inquire about replacement parts, please visit the official AeroCool webstranice ili kontaktirajte njihov odjel za korisničku podršku.

Službeno Webstranica: www.aerocool.io

Please have your product model number (MIRAGEL240W or ACLA-MR2412771) and purchase date ready when contacting support.