Categories: BRANDMOTION

BRANDMOTION TRNS-2100 Transparent Trailer Ultra Wide Display Mirror User Guide

TRNS-2100 Transparent Trailer Ultra Wide Display Mirror
User Guide

Kit Contents

Kit Contents:
1x Video Mirror
2x 10m 4-Pin Video Harness
1x 20m 4-Pin Video Harness
2x External Video Connectors
1x Coiled 4-Pin Harness
1x Power harness

CLICK HERE for our recommended cameras

Installation of the Transparent Trailer Mirror

Part 1 Attaching the Transparent Trailer Mirror to the windshield
1. Remove the Transparent Trailer Mirror from the protective sleeve and ensure that the mirror and mounting arm are oriented as illustrated.
2. Remove the old mirror from the mount on the windshield as per the manufacturer’s directions. Be sure to use the proper removal tool if required.
3. Install new mirror on to D-tab and tighten with a Phillips screwdriver. Please call our offices and select option one if your mirror mount does not look like the illustration.
4. Take care not to overtighten. Overtightening could result in damage to your windshield.
Part 2 Powering the Transparent Trailer Mirror
1. Connect the power harness to the plug on the mirror. Route the harness across the headliner, down the A-pillar, and to the desired location in the kick panel.
2. Ensure that the harness will not be pinched when trim panels are replaced.
Part 3 Wiring the Transparent Trailer Mirror
1. Connect the RED wire from the mirror harness to 12-volt accessory power.
2. Connect the BLACK wire to solid ground.
Chassis ground in the kick panel is recommended.
3. The GREEN wire can be used to trigger Video 1. Otherwise, the mirror will always prioritize Video 2. Green wire can be hooked to a 12V+ switch or any other signal wire required for the desired functionality
Part 4 Function test of the Transparent Trailer Mirror
1. Connect the camera directly to AV2 on the mirror harness
2. Test mirror and camera by turning on ignition power. You should be able to see the view from the rear camera after the mirror powers up.
Part 5 Installing the Rear Trailer Camera Harness and Trailer Plug
1. Using the larger 20m (65 ft) cable harness, connect to the 4-pin connector of the camera and run to the front of the trailer. We recommend running along with the ceiling or under the body along with the frame.
2. Zip tie the cable up along the frame rails. Some trailers have holes cut into the frame rail for factory wiring, try to follow these.
3. Make sure to use the male-ended plug for the trailer. (If the wrong one is used the plug will not be correct for the camera.)
4. Connect the 4-pin harness(s) to the appropriate trailer connector
Part 6 Installing the Vehicle Harness and Plug
1. Using the included template, drill a 1” hole facing the rear of the vehicle’s bumper to mount the vehicle plug. Look behind the bumper or bumper cover to make sure there is nothing on the backside of where the plug is going to go.
2. Using the same template, drill two 3/16” holes for the mounting screws. If you are using the online instructions and do not have a template, you can insert the plug to mark your hole locations, remove the plug, and drill your 3/16” holes
3. Unwind your two 10m harnesses that are attached to the plug and feed through the 1” hole.
4. Attach the plug to the vehicle by removing the 2 nuts and washers. Then attach the plug to the vehicle and secure with the original washers and nuts.
5. Run the harness from the rear of the truck to the area where the mirror is located. If you have a second camera mounted on the trailer, you will need to run both harnesses.
6. Connect the 4-pin connector to the mirror harness 4-pin connector.

FAQ Section

WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov

Installation Instructions – TRNS-2100
AR_04/15/21

Documents / Resources

BRANDMOTION TRNS-2100 Transparent Trailer Ultra Wide Display Mirror [pdf] User Guide
TRNS-2100, Transparent Trailer Ultra Wide Display Mirror, TRNS-2100 Transparent Trailer Ultra Wide Display Mirror

References

Share

Recent Posts

BOFIDAR Touch Screen Bluetooth Smartwatch

BOFIDAR BOFIDAR Touch Screen Bluetooth Smartwatch Specifications PACKAGE DIMENSIONS: 94 x 3.5 x 1.22 inches…

2 mins ago

KICKER CXA360.4 4-Channel 4×90-Watts Class A-B Full-Range Car Audio Amplifier Owner’s Manual

CXA360.4 4-Channel 4x90-Watts Class A-B Full-Range Car Audio Amplifier CX AMPLIFIERS Owner's Manual CXA360.4 Manual…

5 mins ago

PreSonus Studio 68c USB Audio Interface

PreSonus Studio 68c USB Audio Interface Overview Introduction Thank you for purchasing a PreSonus® STUDIO24c…

6 mins ago

Zhizhi S37 Smart Watch for Men Women Fitness

Zhizhi Zhizhi S37 Smart Watch for Men Women Fitness Specifications PACKAGE DIMENSIONS: 38 x 3.7…

8 mins ago

KAKTIN Touch Screen Smartwatch

KAKTIN Touch Screen Smartwatch Specifications PRODUCT DIMENSIONS: 09 x 1.5 x 0.41 inches ITEM WEIGHT:…

14 mins ago

faytech 116N4200APLBMX 11.6 Inch APL Surface Mount Phase 3 User Manual

116N4200APLBMX 11.6 Inch APL Surface Mount Phase 3 BMX 11.6inch APL SurfaceMount Phase3 116N4200APLBMX Manual…

14 mins ago