VTC703AHD
VTC703AHD-Q2
VTC703AHD-Q4
7” 1080P Full HD Digital
Wireless 2/4 Channel Monitor and Camera System
with Digital Video Recorder
USER MANUAL
Please read the instructional complete before use and keep it for future reference.
Product Features
- 1080P Full HD Image Quality System
- 7” All View Angle IPS TFT LCD Panel
- 4 Channel Wireless Monitor with Single, Dual, or Quad View
- Waterproofed, Heavy Duty Wireless Camera
- Reliable Wireless Operational Range up to 300 ft
- Built-in Camera Microphone for Audio Monitoring
- Built-in DVR for Audio/Video Recording up to 4 Channels
- Easy Installation and Operation
Contents
 |
 |
 |
 |
| Monitor Set (1x) |
Camera Set (1x for 1Ch) (2x for Q2) (4x for Q4) |
12V Adapter Power Chords(2x for Ch) (3x for Q2) (5x for Q4) |
Mounting HW |
Before Installation
- Please check the contents.
- Perform bench test. Ensure the product is working before installation by connecting the monitor and the camera to 12VDC.
- Perform a pre-install test, before mounting the monitor and the camera. In very rare instances, a running engine causes interference, resulting in image freezing and jerky object movements. In such a situation, the monitor and the camera need to be moved and positioned at various places to determine the best performance position.
- For recording, please use the high-speed C10 SD memory card.
Wiring
| a. Monitor wiring: | |
 |
Use 12V Adapter. Or Use a power chord. Power cord RED: to ACC+ BLACK: to ground / chassis |
| b. Camera wiring: | |
 |
Use a power chord. Power cord RED: to ACC+ BLACK: to ground/chassis |
Monitor Installation
a. Install the monitor bracket using the 3 self-tapping screws.
- Screw in the center.
- Adjust the angle.
- Tighten all screws.
b. Install the monitor using 2 bolts on each side.
* Do not tighten bolts. 
c. Adjust the monitor angle.
* Tighten all bolts.
Operation
The wireless camera system is operated using the buttons on the front face of the monitor. These are 7 buttons.
Each button has a different function in three different modes. Three different modes are Split Screen Multi-Channel Display Mode, Single Channel Screen Display, and Menu Display Mode.
1. Monitor Button Functions
Split Screen Multi-Channel Display Mode
| Button | Function |
 |
Screen Display On / Off |
 |
Audio Channel – |
 |
– |
 |
Audio Channel + |
 |
Display Mode: Display Channel 1 |
 |
Flip Screen Display Vertically |
 |
Flip Screen Display Horizontally |
Single Channel Screen Display Mode
| Button | Function |
|
Screen Display On / Off |
|
Brightness – |
|
Enter Menu Button |
|
Brightness + |
|
Display Mode: Next Channel |
|
Flip Screen Display Vertically |
|
Flip Screen Display Horizontally |
Menu Mode
| Button | Function | |
|
Screen Display On / Off | |
|
Previous Menu Item | – Decrease |
|
Exit Menu | |
|
Next Menu Item | + Increase |
|
– | |
|
– | |
|
Select Submenu | Confirm |
2. Menu Button – Single Channel Screen Display Mode
 |
Pairing: By pairing assign a camera to each channel |
 |
Pairing: By pairing assign a camera to each channel |
 |
Picture Orientation: Flip L/R, Flip U/D |
 |
Screen Display Settings: Dual, or Quad split screen on/off |
 |
Camera Settings: The camera on/off, Display Scan time |
 |
System Settings: Set date/time, Set parking guidelines |
 |
Playback: Playback recorded video |
 |
Record Settings: Format SD, Rewrite on/off |
3. Pairing:
For a wireless camera to transmit video to a monitor, each camera must be paired with a specific monitor channel (or screen division).
In the following example, Ch 1 has been selected (Ch 1 single-screen display mode).
The menu button is pressed.
‘Pairing’ is selected and the monitor starts count-down immediately.
During the count-down, unplug and plug the camera power, a couple of times.
When pairing is successful, the camera video will be displayed.
To stop pairing, press the menu button ().
4. Picture Settings:
| Decrease | Increase |
 |
Brightness |
 |
Contrast |
 |
Hue |
 |
Volume |
5. Picture Orientation:
 |
Normal Camera pointing forward: An object on the front-right side of the vehicle is displayed on the right side of the screen. |
 |
Normal Camera pointing backward – installed as a rearview camera: Flip image horizontally. An object at the rear-right side of the vehicle is displayed on the right side of the screen. |
 |
Normal Camera installed upside down: Rotate the image (180 degrees) to get the normal view. |
 |
Rearview camera installed upside down: Flip horizontally and rotate the image (180 degrees) to get the normal view. |
6. Screen Display Setting:
The screen divisions, applicable to enabled cameras in “Camera Settings” are enabled (white-colored) and non-applicable screen divisions are disabled (grayed out).
Use or button to the enabled screen division, and then use the OK button to select. Selected screen divisions will pink background 
.
VTC703AHD-Q2: There are only two cameras and if they are paired with Ch 1 and Ch 2, they only 
will be enabled for selection. Other 2-screen divisions ( 
, 
and 
) will be disabled (greyed-out).
VTC703AHD-Q4: If Camera 2 is turned off in the camera setting menu (
), the screen divisions, (, ) will be disabled from selection and grayed out.
When ‘Split Off’ (
) is selected, the split-screen display will not be displayed.
7. Camera Settings:
 |
ON: The selected camera is monitored and recorded. OFF: Not monitored. Not recorded. |
 |
Auto Scan Time. Set the duration time for each channel to be displayed during auto scanning for monitoring purposes. |
 |
Auto Scan ON or OFF. Display a camera for the specified auto-scan time and display the next camera for the specified auto-scan time. And so on. |
Defaults:
VTC703AHD-Q2: Camera 1 and Camera 2 are turned on from the factory.
VTC703AHD-Q4: All cameras are turned on from the factory.
8. System Settings:
 |
Set System Time |
 |
Select UI Language |
 |
Auto-Dim On or Off. The setting dims the display when it becomes dark |
 |
Trigger off display – Not available in this version |
 |
Parking guidelines on/Off |
 |
Reset the system to the factory defaults |
9. Playback Recording:
The recorded video can be played on the monitor.
Here are the steps:
a. From the main menu, select ‘Play’ and the available storage media will be displayed.
b. Select a storage media (by clicking the 
button) and the recording list will be displayed.
c. Use the ‘Up’ or ‘Down’ button to a video file (.MP4) and press the ‘select’ button and the selected video will be played.
d. The recorded video can be played by a PC media player. Remove the SD card and place it on a PC.
10. Record Settings:
 |
ON: Overwrite the oldest recording when storage is full. OFF: Stop recording when storage is full. |
 |
ON: Format SD card. Support up to 128GB Class 10 |
Monitor, Camera, and Wireless Specifications
1. Monitor Specification
| Panel: | 7″ Digital Panel TFT IPS panel |
| View Angle: | Full Angle of View |
| Resolution: | 1024*600 |
| Display Ratio: | 16:09 |
| Audio: | Built-in Speaker with Volume Control Buttons |
| Image Control: | Reverse / Non-Reverse (Horizontal Flip) |
| Parking Guidelines: | Display / No-Display (Selectable) |
| Operating Voltage : | DC12V & DC24V (MAX. to 36V) |
| Power Consumption: | Less than 5W |
| Max. Current: | Less 450mA |
| Storage temperature: | -30°C-80°C |
| Working temperature: | -20°C to 70°C |
2. Camera Specification
| Image Sensor: | 1/3 CMOS sensor |
| Effective Pixels: | 1920 x 1080 |
| Video Transmission: | 1080P AHD |
| View Angle: | 170° (Diagonal) |
| IR Night Vision: | IR |
| Night Vision IR distance: | up to 12ft |
| Audio: | Microphone Built-in |
| Environment: | IP68 |
| Operating Voltage: | DC 12V & 24V |
| Power Consumption: | < 5W |
| Max. Current: | < 450mA |
| Storage temperature: | -30°C-80°C |
| Working temperature: | -20°C to 70°C |
3. Wireless Specification
| Operating frequency: | 2.4GHz-2.4835GHz |
| Output Power: | 17±1dBm @TYp 20dBm@max (if necessary) |
| Modulation Type: | FSK/GFSK |
| RX Sensitivity: | -89dBm(Typical)@4MHz BER:CE-3 |
| RF Bit Rate: | 4MHz BERCE-3 |
| Spread Spectrum: | FHSS |
| Distance: | > 300 ft Open Line of Sight |
4. DVR Specification
| Recording: | Per channel |
| Resolution: | 640×480 or 1024×608 |
| Frame per Second | 30fps |
| Memory Card | SD Class 10 or above |
| Storage Size | Max. 128GB |
WARRANTY INFORMATION
This one-year limited warranty is given to the end-user or the retail purchaser (referred to this warranty as “Original Purchaser”) that it will be free from defects in material and
workmanship for a period of one year from the date of the purchase of the new product (excluding accessory items such as power cords, cradle, memory card, adaptor, and
cables).
This limited warranty does not cover any physical damage to, or misuse of, this product, damage caused by improper installation; improper use; misuse; neglect; repair of cracked, scratched, broken, or modified cosmetics; or parts that have been altered or removed; damages done by another device used with this product resulting from use of non BOYO®- brand parts. This warranty is VOID if you purchased this product as used, floor model sample, or refurbished; if the product has been altered or modified in any way (including but not limited to attempted repair without authorization from BOYO®- Vision Tech America, Inc. and/or alteration/removal of the serial number).
For warranty information, visit: https://www.visiontechamerica.com/get-warranty
For technical support:
Call: (888) 941-3060
Email: info@visiontechamerica.com
Visit: www.VisionTechAmerica.com 
Rear View Camera
REVθ83θ2θ13
1 YEAR LIMITED WARRANTY
This limited warranty is given to the end-user or the retail purchaser (referred to this warranty as “Original Purchaser”) that it will be free from defects in material and workmanship for a period of one year from the date of the purchase of the new product (excluding accessory items such as power cords, cradle, memory card, adaptor, and cables). A copy of the original proof of purchase and this warranty card with the RMA number given by Vision Tech America, Inc . is required to receive warranty service. In the unlikely event that the new product should fail due to a defect in material or workmanship, Vision Tech America, Inc . will repair or replace it with a new or refurbished product, where each party will be responsible for one-way shipping for the lower 48 states customers only. For International and U.S custom ers residing in Hawaii, Alaska, and Puerto Rico, the customer is responsible for freight charges incurred both ways.
This limited warranty does not cover any physical damage to this product, damage caused by improper installation; improper use; misuse; neglect; repair of cracked, scratched, broken, or modified cosmetics; or parts that have been altered or removed; damages done by another device used with this product resulting from use of non BOYO®- brand parts. This warranty is VOID if you purchased this product as used, floor model sample, or refurbished; if the product has been altered or modified in any way (including but not limited to attempted repair without authorization from BOYO~- Vision Tech America, Inc . and/or alteration/removal of the serial number). This limited warranty does not cover the vehicle of any damages or liabilities in which this product is installed or is being installed. This product does not guarantee avoidance of vehicle collision or accident.
If you are having trouble with the product, please contact our technical support at 888 -941-300S or email: info@visiontechamerica.com with your questions or comments.
If your product is eligible to receive a warranty, request warranty service online by visiting http://visiontechamerica.com/site/get-warranty/
This warranty is invalid if the factory-applied serial number has been altered or removed from the Product.
IMPORTANT: TO SEND DEFECTIVE PRODUCTS FOR WARRANTY SERVICE, YOU MUST RECEIVE RMA (RETURN MATERIAL AUTHORIZATION) AND INCLUDE ORIGINAL PROOF OF PURCHASE AND THIS WARRANTY CARD WITH THE SHIPMENT.
VISION TECH AMERICA CUSTOMER SERVICE CENTER
888-941 -300S or visit www.visiontechamerica.com
For an accessory or part not available from your authorized dealer, call
For U.S. 888-941-300S I International 714-446-&543 Product Registration
Vision Tech America, Inc.
Name…………………………………………….Company………………………………..
Address ………………………………………………………………………………………..
City……………………….State……………………………Zip…………………………….
Phone……………………………………………Email…………………………………….
Model No……………………………………..Serial No……………………………….
Purchased Date…………………………..Store Name…………………………….
City/State of Store……………………………………………………………………..
Place
Postage
StampVision Tech America, Inc.
1452 E. Valencia Drive
Fullerton, CA 92831Product Registration
Vision Tech America, Inc.
Name…………………………………………….Company………………………………..
Address ………………………………………………………………………………………..
City……………………….State……………………………Zip…………………………….
Phone……………………………………………Email…………………………………….
Model No……………………………………..Serial No……………………………….
Purchased Date…………………………..Store Name…………………………….
City/State of Store……………………………………………………………………..
Place
Postage
Stamp
HereVision Tech America, Inc.
1452 E. Valencia Drive
Fullerton, CA 92831
Documents / Resources
 |
BOYO VTC703AHD Wireless 2/4 Channel Monitor and Camera System [pdf] User Manual Wireless, Channel Monitor, Camera System, VTC703AHD |
Backup Camera and Monitor | Rear View Cameras 
