Bosch Dishwasher User Manual - Optimized PDF Bosch Dishwasher User Manual - Original PDF
This manual contains many DANGER, WARNING, and CAUTION indicators concerning the consequences of failure to use, assemble, maintain, store, inspect and dispose of a Bosch-equipped eBike in a safe manner.
Save all safety warnings and instructions for future reference. The term battery pack used in these operating instructions refers to all original Bosch eBike battery packs.
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important safety and operat-ing instructions for this battery charger.
NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
NOTICE: Changes or modifications made to this equipment not expressly approved by the Robert Bosch GmbH may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
|Charger 4A Charger|
|Rated voltage of the rechargeable battery||V=||36|
|Charging current (max.)||A||4|
|Charging time for PowerTube 750 approx.||h||6|
|Operating temperature||°F||32 to 104|
|Storage temperature||°F||50 to 104|
|Article number||1 270 020 343|
|Rated voltage – cables||V~||300|
|Rated voltage – connectors/plug-in connectors||V~||125|
|Rated current – connectors/plug-in connectors||A||10|
|Material – cables||PVC|
|Safety standard – cables||UL 62|
|Safety standard – connectors/plug-in connectors||UL 817|
Connecting the charger to the mains
Note the household voltage! The voltage of the power supply must correspond to the specifica-tions given on the battery charger nameplate. Plug the device connector (3) of the power cable into the device socket (2) on the charger. Connect the power cable (country-specific) to the mains. Use only the supplied input connection: standard AC power cord ((3) in the diagram) when connecting to the household electrical supply. Switch the battery off and remove it from its holder on the eBike. When doing so, read and observe the operating instructions of the battery. Ensure the battery is placed on clean surfaces only. Avoid getting dirt, e.g. sand or soil, in the charging socket and contacts in particular. Plug the charging connector (5) of the charger into the socket (6) on the battery.
Charging the battery when inserted in the bicycle
Switch the battery off. Clean the cover of the charg-ing socket (7). Avoid getting dirt, e.g. sand or soil, in the charging socket and contacts in particular. Lift the cover of the charging socket (7) and plug the charging connector (5) into the charging socket (6).
The charging process begins as soon as the charger is connected to the battery or charging socket on the bike and to the mains.
Note: The charging process is only possible when the temperature of the eBike battery is within the permit-ted charging temperature range.
Note: The drive unit is deactivated during the charging process. The battery can be charged with or without the onboard computer. When charging without the onboard computer, the charging progress can be observed via the battery charge indicator. When the onboard computer is connected, a charging notification appears on the display. The state of charge is displayed by the battery charge indicator (8) on the battery and by the bars on the onboard computer. The LEDs on the battery charge indicator (8) will flash during the charging process. Each solid illuminated LED represents approximately 20 % of the charging capacity. The flashing LED indicates the next 20 %currently charging. Once the eBike battery is fully charged, the LEDs extinguish immediately and the onboard computer is switched off. The charging process is terminated. The state of charge can be displayed for 5 seconds by pressing the on/off button (9) on the eBike battery. Disconnect the charger from the mains and the battery from the charger. When the battery is disconnected from the charger, the battery is automatically switched off.
After-sales service and advice on using products
If you have any questions about the eBike system and its components, contact an authorized bicycle dealer. For contact details of authorized bike dealerships, please visit www.bosch-ebike.com. Please contact an authorized bicycle dealer if the battery is no longer working.
|BOSCH BPC3410 Standard Charger [pdf] Owner's Manual|
BPC3410, Standard Charger, BPC3410 Standard Charger
Nintendo Neon Purple/ Neon Orange Joy-Con (L-R) Specifications BRAND: Nintendo VIDEO GAME PLATFORM: Nintendo Switch…
00182600 MC-100 Optical 3-Button Mouse 3-Button Mouse 00182600 A MC-100 B 1 G Warranty Disclaimer…
00182648 Pesaro Mini Mouse xx182648 A B C G Note on environmental protection: xx182649 After…
GECME003D-U Espresso Machines 15 Bar with Milk Frother COFFEE MAKER INSTRUCTION MANUAL GECME003D-U IMPORTANT SAFEGUARDS…
LAP-C202S-WUSR VeSync Core 200S Plus Smart True HEPA Air Purifier CoreTM 200S Series USER MANUAL…