Bluestone TWS2 True Wireless
Earbuds User Manual

Bluestone TWS2 True Wireless Earbuds User Manual

Product Overview

Bluestone TWS2 True Wireless Earbuds - Product Overview

Charging Case:

  1. Connect the Micro USB end of the provided Charging Cable into the Micro USB Port of the Charging Case.
  2. Connect the USB end of the USB Charging Cable into any USB Charging Port.
  3. Press the Charging Box Power Button. While charging the Charging Case Indicator Lights will blink.
  4. All four Charging Case Indicator Lights will turn off when it’s fully charged.

Charging Earbuds:

  1. Charge the Earbuds by placing them into the already charged Charging Case.
  2. The Ear Bud Indicator Lights will glow red while being charged and the Charging Case Indicator lights will glow blue.
  3. All Indicator Lights will turn off once the earbuds are fully charged.

Pair a Single Earbud:

  1. Hold down the Multi-Function Button for 3 Seconds.
  2. The Pairing Indicator Light will flash until the earbud appears on your device’s Bluetooth Interface.
  3. Select •BluestonelWS2″from your device’s Bluetooth Interface.
  4. Your Wireless Earbud should now be connected to your device.

Pair Both Earbuds (TWS):

  1. Simultaneously hold down the Multi-Function Button on Both earbuds for 3 Seconds.
  2. The Pairing Indicator Light will blink red and blue and a sound will prompt that they are being paired.
  3. The blue light will blink slowly to indicate that they have been successfully paired.
  4. Select “Bluestone TWS2” from your device’s Bluetooth Interface.

(If you have trouble pairing please refer to your Device’s Bluetooth Pairing Instructions as methods may differ.)

  • After a successful connection you can listen to music and make a phone call.
  • Shut down, play, and pause can be controlled by either multi-function button.
  • After pairing for the first time just press the multi-function button to automatically reconnect.

Make a Call:

  1. Connect the earbuds to your Phone’s Bluetooth.
  2. Use your Phone’s interface to make a call.
  3. To receive an incoming call press the Multi-Function Button once.
  4. To deny an incoming call quickly press the Multi-Function Button twice.

Listen to Music:

  1. Connect the earbuds to your Phone’s Bluetooth.
  2. Use your Phone’s interface to select your music.
  3. Once paired music will automatically play through the earbuds.
  4. Press the Multi-Function Button to Pause/Play Music.

Turn Off the Earbuds:

  1. Press the Multi-function Button for up to 5 Seconds or until the red light starts to blink.
  2. The earbuds will automatically turn off if they are out of reach of the Bluetooth Device or if the Bluetooth Device shuts down.

IMPORTANT SAFEGUARDS

  • Do not use this unit for anything other than its intended use.
  • Keep the unit away from heat source, direct sunlight, humidity, water or any other liquid.
  • Do not expose the device to extremely high or low temperatures, as it may damage the battery.
  • Do not operate the unit if it has been wet or moist to prevent against electric shock and/or injury to yourself and damage to the unit.
  • Do not use the unit if it has been dropped or damaged in any way.
  • Repairs to electrical equipment should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.
  • Keep the unit out of reach of children.
  • This unit is not a toy.

BATTERY DISPOSAL:
This product contains a lithium polymer battery. Lithium polymer batteries are environmentally safe when fully discharged. Please refer to your local and state laws for battery disposal procedures.

©SM TEK GROUP INC, All rights reserved.
BlueStone is a trademark of SM TEK GROUP INC.
New York, NY 10001
www.smtskgroup.com

1 Year Limited Warranty
Please Email [email protected]

Made in China


Bluestone TWS2 True Wireless Earbuds User Manual – Optimized PDF
Bluestone TWS2 True Wireless Earbuds User Manual – Original PDF

Leave a comment

Your email address will not be published. Required fields are marked *