Bissell 2306 Series CrossWave PET User Guide

Bissell 2306 Series CrossWave PET

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR CROSSWAVE® PET.
When using an electrical appliance, basic precautions should be observed, including the following:

Warning Icon WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

  • Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
  • Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.
  • Use indoors only.
  • Do not allow to be used as a toy. Close attention is necessary when used by or near children.
  • Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.
  • Do not use with damaged cord or plug. If appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
  • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
  • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
  • Do not handle plug or appliance with wet hands.
    Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
    Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
    Turn off all controls before plugging or unplugging appliance.
    Use extra care when cleaning on stairs.
    Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
  • Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
  • Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
  • Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
  • Use only BISSELL cleaning products intended for use with this appliance to prevent
    internal component damage. See the Cleaning Fluid section of this guide.
  • Do not immerse. Use only on surfaces moistened by the cleaning process.
  • Keep appliance on a level surface.
  • Do not carry the appliance while in use.
  • Always install float before any wet pick-up operation.

Warning Icon WARNING: Risk Of Injury. Brush May Start Unexpectedly. Unplug Before Cleaning or Servicing.
Warning Icon WARNING: To Reduce The Risk Of Injury From Moving Parts – Unplug Before Servicing.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

Induction

Thanks for buying a BISSELL

CrossWave® Pet We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your multi-surface cleaner works as well in two years as it does today, so this guide has tips, maintaining , and if there is a problem, take guideline from troubleshooting . Your multi-surface cleaner needs a little assembly before you can put it to work, so flip to assembly instructions and let’s get started!

What’s In The Box?

Box Items Induction

Getting to Know Your CrossWave® Pet

  1. Upper Handle
  2. SmartClean Fingertip Controls
  3. Strainer
  4. Float Stack
  5. Easy Remove Brush Window
  6. Integrated Carry Handle
  7. Dirty Water Tank
  8. Foot
  9. Solution Spray Trigger
  10. Quick Release Cord Wrap
  11. Clean Water Tank
  12. Lower Cord Wrap
  13. Rinse Cup
  14. Rinse and Storage Tray

Product Overview

Your BISSELL CrossWave® Pet machine comes in three easy to assemble components and does
not require any tools to assemble. The unit also comes with a three-piece Rinse and Storage Tray.

  • Handle
  • Body
  • Clean Water Tank
  • Rinse and Storage Tray
  • Brush Roll Drying Tray with Rinse Cup

Assembly

Warning Icon WARNING: Do not plug in your CrossWave® Pet until you are familiar with all instructions and operating procedures.

  1. Insert handle into body of unit until you hear a click.
    Assembly Induction
  2. Then, on the back of the machine, align clean water tank with the grooves and slide tank into place until you hear a click.
    Assembly Induction
  3. Wrap the cord around the quick release cord wrap and the lower cord wrap.
    Assembly Induction
  4. The multi-functional rinse and storage tray includes a machine storage tray, brush roll drying tray with rinse funnel, and rinse cup. To assemble, slide the over hang in the middle of the brush roll drying tray with rinse funnel down into the opening on the storage tray that is indicated with arrows. Then, place the rinse cup into the rinse funnel.
    Assembly Induction

NOTE: To easily unwrap the cord for use, just turn the quick release cord wrap downward
to remove the cord from the cord wrap.

Cleaning Formulas

WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the hard floor device.

CROSSWAVE® FORMULAS

 Cleaning Formulas Induction Cleaning Formulas Induction    Cleaning Formulas Induction Cleaning Formulas Induction 

Multi-Surface Formula

Wood Floor Formula

Area Rug Formula

Multi-Surface Pet with Febreze Formula

Great for cleaning ALL sealed floors and area rugs

Restore your wood floors’ natural shine

 

Removes stuck on and embedded dirt from area rugs

Removes Pet odors to clean and refresh

Keep plenty of CrossWave® formulas on hand so you can clean your hard floors and area rugs whenever it fits your schedule. Always use CrossWave® formulas in your machine. Other solutions may harm the machine and void the warranty.

Filling Your Clean Water Tank

  1. The clean water tank is located on the back of the machine.
    Filling Clean Water Tank Induction
  2. Lift the clean water tank straight up to remove from the machine.
    Filling Clean Water Tank Induction
  3. Unscrew the cap from the clean water tank. The clean water tank has two measuring volumes depending on the amount of space you would like to clean
    Filling Clean Water Tank Induction
  4. For large area cleaning (up to 700 sq ft)
    a. Fill formula tank with warm tap water to the second water fill line.
    b. Then add formula to the second formula fill line.
    Filling Clean Water Tank Induction
    For small area cleaning (<350 sq ft)
    a. Fill formula tank with warm tap water to the first water fill line.
    b. Then add formula to the first formula fill line.
    Filling Clean Water Tank Induction
  5. Screw the cap back onto the clean water tank.
    Filling Clean Water Tank Induction
  6. On the back of the machine, align clean water tank with the grooves and slide tank into place until you hear a click.

    Filling Clean Water Tank Induction

A few notes about filling the clean water tank:
• Fill with warm (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE.

Cleaning Your Hard Floors

  1. Plug machine into a properly grounded outlet.
    Cleaning Hard Floors Induction
  2. Select cleaning mode: To start cleaning your hard floors, turn the machine ON pressing the HARD FLOOR button. Once the setting is selected, the dry vacuum will turn on. To turn OFF, press the HARD FLOOR setting a second time.
    Cleaning Hard Floors Induction
  3. Recline the body of the machine backward to start the brush roll spinning. To stop the brush roll spinning, you will need to stand the machine upright.
    Cleaning Hard Floors Induction
  4. Before each use, hold the solution spray trigger for 10 seconds to prime the system with cleaning solution. LED lights illuminate when holding the trigger.
    Cleaning Hard Floors Induction
    NOTE: When solution is flowing, you will see bubbles forming at the edges of the brush roll window.
  5. To clean, hold the solution spray trigger to apply solution on both forward and backward passes.
    Cleaning Hard Floors Induction
  6. To dry hard floors faster, release the trigger and clean a second pass without dispensing solution.
    Cleaning Hard Floors Induction

TIP: When cleaning excessively dirty or muddy hard floors or if your brush roll looks dirty, use the easy clean storage tray to rinse your brush roll before cleaning your area rugs.

TIP: For overly challenging and stuck-on messes on your hard floors, activate the RUG mode and hold your CrossWave® Pet over the mess. Using short passes while holding the trigger allows the multi-surface brush to go to work.

Cleaning Area Rugs

NOTE: Before cleaning area rugs, test an inconspicuous area of the rug for colorfastness. Also, please check manufacturer’s tag before cleaning area rugs for any specialized cleaning instructions. Not for use on silk or delicate area rugs.

  1. Plug machine into a properly grounded outlet.
    Cleaning Induction
  2. Select cleaning mode: To start cleaning your rugs, turn the machine ON pressing the RUG button. Once the setting is selected, the dry vacuum will turn on. To turn OFF, press the RUG setting a second time.
    Cleaning Induction
  3. Recline the body of the machine backward to start the brush roll spinning. To stop the brush roll spinning, you will need to stand the machine upright.
    Cleaning Induction
  4. Before each use, hold the solution spray trigger for 10 seconds to prime the system with cleaning solution. LED lights illuminate when holding the trigger.
    Cleaning Induction
    NOTE: When solution is flowing, you will see bubbles forming at the edges of the brush roll window.
  5. To clean, hold the solution spray trigger to apply solution on both forward and backward passes.
    diagramCleaning Induction
  6. To dry area rugs faster, release the trigger and clean a second pass without dispensing solution.
    Cleaning Induction

NOTE: The RUG button dispenses twice the solution of the HARD FLOOR button
to help with area rug cleaning.

NOTICE: Do not over wet carpet. Be careful not to run over loose objects or
edges of area rugs. Stalling the brush may result in premature belt failure.

Maintenance: Rinse and Storage Tray

Warning Icon WARNING: To reduce the risk of fi re, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.

  1. Place unit on rinse and storage tray.
    Maintenance Induction
  2. Fill rinse cup with water.
    Maintenance Induction
  3. Pour water into rinse funnel to fill the MAX line of the rinse and storage tray.
    Maintenance Induction
  4. Turn the machine ON by pressing the Hard Floor button.
    Maintenance Induction
  5. Recline the machine while in storage tray. Allow the machine to run for 10-15 seconds until all water is picked up. Repeat as needed.
    Maintenance Induction
  6. Grasp brush roll window at the front of the window and pull upward to remove.
    Maintenance Induction
  7. Pull brush roll out by grabbing the brush roll tab and pulling upward.
    Maintenance Induction
  8. Place the brush roll upright in the brush roll drying tray to dry.
    Maintenance Induction
  9. Replace brush roll by inserting the brush roll end into the right side of the foot. Then lock the pull tab into place by pressing downward.
    Maintenance Induction
  10. Replace the brush roll window by first lining up the brush window tabs with the edges of the foot. Then press the window back into place until you hear a click.
    Maintenance Induction

Machine Storage
Put the unit away in a closet or basement until the next use. Store cleaner in a protected, dry area

NOTE: Any solution remaining in the clean water tank should be emptied prior to machine storage.

NOTICE: To reduce the risk of a leaking condition, do not store unit where freezing may occur. Damage to internal components may result.

Maintenance: Dirty Water Tank

WARNING: To reduce the risk of fi re, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting

  1. To release dirty water tank, press down on recessed button on the top of the dirty tank.
    Maintenance Induction
  2. Grab the front handle while pressing down on button and pull dirty water tank away from the unit.
    Maintenance Induction
  3. Grasp top of dirty water tank in recessed areas on each side of the filter and pull upward to
    remove the top of the tank.
    Maintenance Induction
    Did You Know?
    The float is what prevents your dirty tank from overflowing. When your dirty tank is full, the float will shut off your suction motor creating a high pitched sound indicating it is time to empty your dirty water tank.
  4. Remove strainer from dirty tank then throw debris in trash.
    Maintenance Induction
  5. Pour dirty water out. Rinse the inside of the dirty water tank.
    Maintenance Induction
  6. Remove the filter from the top of the dirty water tank by pulling it up.
    Maintenance Induction
  7. Hand wash the vacuum filter and screen with warm water and mild detergent.
    Maintenance Induction
  8. Rinse the float located at the bottom of the top of the dirty water tank.
    Maintenance Induction
  9. If the inside area where the dirty water tank sits is dirty, wipe it clean with a rag or towel.
    Maintenance Induction
  10. Leave parts out to dry before reassembling.
    Maintenance Induction
  11. Place vacuum filter back into the top of the dirty water tank.
    Maintenance Induction
    NOTE: Make sure to clean your dirty tank and let all components dry out after each use to keep your product at its best.
  12. Place strainer back into dirty water tank.
    Maintenance Induction
  13. Once parts are dry, reassemble and replace the top of dirty water tank.
    Maintenance Induction
  14. Angle the dirt tank back into body of machine inserting bottom first. Then tilt the top of the dirt tank toward the machine and push into place until you hear a click.
    Maintenance Induction

Maintenance: Brush Roll and Chamber

Warning Icon WARNING: To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.

  1. Grasp brush roll window at the front and pull upward to remove.
    Maintenance Induction
  2. Pull brush roll out by grabbing the brush roll tab and pulling upward.
    Maintenance Induction
  3. With warm water, rinse your brush roll window and brush roll.
    Maintenance Induction
  4. If your brush roll chamber is dirty, clean with a rag or towel.
    Maintenance Induction
  5. Let your brush roll and brush roll window chamber dry before reassembling.
    Maintenance Induction
  6. Replace brush roll by inserting the brush roll end into the right side of the foot. Then lock
    the pull tab into place by pressing downward.
    Maintenance Induction
  7. Replace the brush roll window by first lining up both brush window tabs with the edges of the foot. Then press the window back into place until you hear a click.
    Maintenance Induction

TIP: Running your machine with a wet brush roll will help the brush roll dry faster. The trigger should not be pressed.
NOTE: The brush roll is not dishwasher or automatic washing machine safe. Please follow cleaning instructions above.

Troubleshooting

Problem

Possible Causes

Remedies

 

 

Reduced spray OR no spray

Clean water tank may be empty Refill tank Clean water tank may not be seated completely
Clean water tank may not be seated completely Turn power OFF / Remove and reseat tank
System isn’t completely primed Hold trigger for 10 to 15 seconds
Brush window is not latched in place Turn power OFF / Unplug machine and re-install brush window
Not holding trigger to spray solution Hold trigger continuously while using the machine
Spray tips on foot clogged Use a pin to clean the spray tips located underneath the brush roll window
 

 

Loss of suction power

Tanks may not be seated properly Turn Power OFF / Remove both tanks and reseat them so they fit properly
Dirty tank has picked up maximum amount of dirty water and has reached full line Empty dirty tank and make sure to make slow cleaning passes back and forth while cleaning
Brush window is not latched in place Turn Power OFF / Unplug machine and re-install brush window
Debris channel in foot is clogged Clean the channel with a paper towel
Filter clogged by debris Remove debris clogging the filter screen and clean the filter
Brush roll is not turning Brush roll is not installed properly Turn Power OFF / Unplug machine and follow instructions for replacing brush roll
Machine is standing upright Recline machine to make brush roll turn on
Obstruction has caused brush roll to stop Turn Power OFF / Unplug machine and remove brush window and brush roll cleaning hair and string off of brush ends
Machine won’t turn on Obstruction has caused brush roll to stop and shut down machine Unplug machine to reset the system. While the machine is unplugged, remove the brush window and brush roll cleaning hair and string off of brush ends
Handle not inserted properly into body of machine Remove the handle and re-insert into the body of the machine making sure to push down until you hear a “click”
Machine is leaking Cap of clean water tank is not closed properly Remove the clean water tank and re-apply the cap
Machine is streaking Too much water applied Go over area without spraying down water
Previous floor care products used Contact product manufacturer regarding how to remove

Warranty

If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Care by E-mail or telephone as described below.
Limited Three-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL will repair or replace (with new, refurbished, lightly used, or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for three years any defective or malfunctioning part. See information below on “If your BISSELL product should require service”. This warranty applies to product used for personal, and not commercial or rental, service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User’s Guide is not covered. This warranty will only be valid if the product is used in the same country in which it was sold.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

NOTE: Please keep your original sales receipt. It provides proof of date of
purchase in the event of a warranty claim.

Service

If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.
Website: www.BISSELL.ca/service-centers
E-mail:   www.BISSELL.ca/email-us
Call:       BISSELL Consumer Care 1-800-263-2535
Monday – Friday 8am – 10pm ET
Saturday               9am – 8pm ET
Sunday                10am – 7pm ET

Please do not return this product to the store. Other maintenance or service not included in the manual should be performed by an authorized service representative. For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-263-2535.

Register your product today!

Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:

Faster Service
Supplying your information now saves you time should you need to contact us with questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.BISSELL.ca/registration!

Visit us online at: BISSELL.ca When contacting BISSELL, have model number of cleaner
available.
Please record your
Model Number: ________________________________
Please record your
Purchase Date: _________________________________
NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim. See the Warranty  for details

Parts & Supplies
For Parts and Supplies, go to BISSELL.ca and enter your model number in the search field.

We can’t wait to hear from you!
We really do read your comments, tweets, and posts. Rate this product on BISSELL.ca
or any of our retailer sites and let us (and millions of your closest friends) know what you think!

 

 

 

 

Bissell 2306 Series CrossWave PET User Guide – Download [optimized]
Bissell 2306 Series CrossWave PET User Guide – Download

Leave a comment

Your email address will not be published.