Bissell 2288 Series Iconpet Cordless Vacuum Cleaner User Guide

2288 Series Iconpet Cordless Vacuum Cleaner

ICONPET® CORDLESS VACUUM
MODEL SERIES 2288, 2774
Go online for a comprehensive walkthrough of your product!
This guide has everything you need to get ready for first use, including setting up, using and maintaining your machine, but online you’ll find additional resources like tips and troubleshooting, videos, product registration, parts and more. Go to support.BISSELL.com.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR APPLIANCE. When using an electrical appliance, basic precautions should be observed, including the following:

WARNING

· Keep charger cord away from heated surfaces. · To unplug, grasp the charger plug, not the cord.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

· Do not handle charger plug or appliance with wet hands.

· Keep hair, loose clothing, fingers, and all parts of body away from openings · Battery pack, charging port on the hand vac and charger output are not to

and moving parts. Brush Roll continues to rotate when in use.

be short-circuited.

· Brush Roll continues to turn while product is turned ON and handle is in use. · The appliance must be disconnected from the battery charger when

To avoid damage to carpet, rugs, furniture and flooring, avoid tipping cleaner removing the battery.

or setting it on furniture, fringed area rugs, or carpeted stairs during tool use. · The battery is to be disposed of safely.

· With Brush Roll ON, do not allow cleaner to sit in one location for an extended · Do not recharge, disassemble, heat above 60°C/140°F, or incinerate.

period of time, as damage to floor can result.

· Keep batteries out of reach of children.

· Do not expose to rain. Store indoors.

· Dispose of used batteries promptly.

· Do not use on wet surfaces.

· This appliance contains batteries that are only replaceable by skilled persons.

· Do not allow to be used as a toy.

· Prevent unintentional starting. Ensure the switch is in the OFF-position

· Close attention is necessary when used by or near children.

before picking up or carrying the appliance. Carrying the appliance with your

· Children should be supervised to ensure that they do not play with the

finger on the switch or energizing appliance that have the switch on invites

appliance.

accidents.

· Plastic film can be dangerous. To avoid danger of suffocation, keep away · Under abusive conditions, liquid may be ejected from the battery; avoid

from children.

contact. If contact accidentally occurs, flush with water. If liquid contacts eyes,

· Do not immerse in water or liquid.

additionally seek medical help. Liquid ejected from the battery may cause

· Do not use for any purpose other than described in this user guide.

irritation or burns.

· Use only manufacturer’s recommended attachments.

· Do not use appliance that is damaged or modified. Damaged or modified

· If appliance is not working as it should, has been dropped, damaged, left batteries may exhibit unpredictable behavior resulting in fire, explosion or

outdoors, or dropped into water, have it repaired at an authorized service risk of injury.

center.

· Do not expose appliance to fire or excessive temperature. Exposure to fire or

· Do not charge the appliance outdoors.

temperature above 130°C/266°F may cause explosion.

· Do not incinerate the appliance even if it severely damaged. The batteries · Follow all charging instructions and do not charge the appliance outside of

can explode in a fire.

the temperature range specified in the instructions. Charging improperly or

· Do not put any object into opening.

at temperatures outside of the specified range may damage the battery and

· Do not use with any opening blocked.

increase the risk of fire.

· Keep openings free of dust, lint, hair and anything that may reduce airflow. · Have servicing performed by a qualified repair person using only identical

· Use extra care when cleaning stairs.

replacement parts. This will ensure that the safety of the product is

· Do not pick up flammable materials (lighter fluid, gasoline, kerosene, etc.) or maintained.

use in the presence of explosive liquids or vapors.

· Do not modify or attempt to repair the appliance except as indicated in the

· Always turn OFF this appliance before connecting or disconnecting the

instructions for use and care.

motorized nozzle.

· Keep the temperature range of between 4-40°C/40-104°F when charging

· Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.). battery, storing unit or during use.

· Do not use vacuum cleaner in an enclosed space filled with vapors given · Use only with charger provided by manufacturer SIL, Model SSC-320110US.

off by oil-based paint, paint thinner, some moth-proofing substances,

· Recharge only with the charger specified by the manufacturer. A charger that

flammable dust, or other explosive or toxic vapors.

is suitable for one type of battery pack may create a risk of fire when used

· Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc. with another battery pack.

· Do not pick up anything that is burning or smoking, such as cigarettes,

· Unplug charger from electrical socket when not in use, before cleaning,

matches or hot ashes.

maintaining or servicing the appliance, and if your appliance has an

· Do not use without Dirt Tank or filters in place.

accessory tool with a moving brush, before connecting or disconnecting

· Use only on dry, indoor surfaces.

the tool.

· Keep appliance on a level surface.

· This appliance contains batteries that are non-replaceable.

· Disconnect battery pack before cleaning or servicing.

· The battery must be removed from the appliance before it is scrapped.

· If the charger supply cord is damaged, it must be replaced by the

· Do not use with damaged cord or charger. If appliance is not working as it

manufacturer, its service agent or similarly qualified person in order to avoid should, has been dropped, damaged, left outdoors, or dropped into water,

a hazard.

return it to a service center.

· Do not pull or carry charger by cord, use cord as a handle, close door on cord, · Turn OFF all controls before unplugging.

or pull cord around sharp edges or corners.

SAVE THESE INSTRUCTIONS
THIS MODEL IS FOR HOUSEHOLD USE ONLY.
COMMERCIAL USE OF THIS APPLIANCE VOIDS THE MANUFACTURER’S WARRANTY.

WARNING
This product contains Lithium-Ion rechargeable batteries. DO NOT mix Lithium-Ion batteries with general household waste. According to Federal and State regulations, removal and proper disposal of Lithium-Ion batteries is required. For specific battery disposal instructions please contact Call2Recycle at 877-723-1297 or visit www.call2recycle.org. For full instructions on battery removal for recycling visit support.BISSELL.com. 2 BISSELL.com

We’re so happy you chose ICONPET® High-Powered Cordless Vacuum. We put this guide together to help you set up, use and maintain your cordless vacuum. We’ve also included some tips we think will come in handy when you first start using your cordless vacuum, so let’s get started!
For a comprehensive walkthrough of your product, go to support.BISSELL.com.

What’s in the Box? . . . . . . . . . . . . . . . . . . 4 Getting to Know Your Vacuum . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Wall Storage & Charging Station . . . . . . . . . . . . . . . . . . . . 5 Charging the Battery . . . . . . . . . . . . . . . . 6 Using the Vacuum. . . . . . . . . . . . . . . . . . . 7

Using the Parking Brake . . . . . . . . . . . . . 7 Attaching Tools for Hand Vac Use . . . 8 Emptying the Dirt Tank . . . . . . . . . . . . . . 9 Removing the Brush Roll . . . . . . . . . . . . 9 Cleaning & Replacing the Filters . . . . 10 Troubleshooting. . . . . . . . . . . . . . . . . . . . . 11 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

BISSELL.com 3

What’s in the Box?
Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the underside of the insert inside the carton.

Hand Vacuum Assembly

Extension Wand

Motorized Floor
Cleaning Foot

Battery Charger

Wall Storage & Charging
Station

Lighted Crevice Tool
& Dusting Brush

Motorized TurboBrush®
Tool

Getting to Know Your Vacuum
For additional support videos and information about your vacuum, visit support.BISSELL.com.

Product View
1. Hand Vacuum Assembly 2. Power Button 3. Cleaning Mode Button 4. Tank Release Button 5. Dirt Tank 6. Hand Vacuum Release Button 7. Extension Wand 8. Foot Release Button 9. Tangle-Free Brush Roll 10. Parking Brake 11. Motorized Floor Cleaning Foot 12. LED Headlights 13. Charging Port 14. Post-Motor Filter 15. Foot Hose

1 2 3 4
5
6
7

13 14

8

9

10

11

15

12

4 BISSELL.com

Assembly
Go to support.BISSELL.com for assembly videos.

1. Connect the Extension Wand to Motorized Floor Cleaning Foot. You’ll hear a “click” when they’re connected.

2. Connect the Hand Vacuum Assembly to the Extension Wand. You’ll hear a “click” when they’re connected.

3. Make sure to charge your stick vacuum before first use. Refer to page 6, “Charging the Battery” for instructions.

Installing the Wall Storage & Charging Station
Go to support.BISSELL.com for more tips and video instructions on installing the Wall Storage & Charging Station.

1. Open the Wall Storage & Charging Station, use the bubble level to ensure it is level and insert two screws to secure to wall. In order to charge the machine, ensure the Wall Storage & Charging Station is mounted near a wall outlet.

2. Insert the tool holders into the side of the Wall Storage & Charging Station. To install the charging cord, remove the power cord clip from the Wall Storage & Charging Station. Insert the charging cord and secure it with the charging cord clip.

3. Plug the power adapter into the wall and place the machine on the Wall Storage & Charging Station for charging. Refer to page 6, “Charging the Battery” for instructions.
BISSELL.com 5

Charging the Battery
Go to support.BISSELL.com for additional how-to videos. Before first use, make sure to fully charge your stick vacuum for 4 hours to get a full charge. To charge the battery you can plug the charger directly into the Hand Vacuum Assembly or into the Wall Storage & Charging Station.
Charging with the Hand Vacuum
4

1. Plug the battery charger into 2. Plug the charger into the

the wall.

charging port on the back side

of the hand vacuum.

3. Let the hand vacuum charge for 4 hours or until all three sections of the battery charge icon are illuminated.

Charging with the Wall Storage & Charging Station

4

1. Follow instructions on page 5 for installing the Wall Storage & Charging Station. Once installed, hang the machine onto the station.
6 BISSELL.com

2. Let the vacuum charge for 4 hours or until all three sections of the battery charge icon are illuminated.

Using the Vacuum
Looking for more guidance? Go to support.BISSELL.com for tips and 24-7 support while cleaning.
ICONPET® Cordless can be used as a stick vacuum, hand vacuum or for extended reach with hand vacuum + wand.

1. Press the Power Button to begin cleaning and to turn OFF the machine when finished cleaning.

2. Press the Cleaning Mode Button to toggle between the three settings: ··· Recommended for maximum suction. It’s the most powerful setting which is great for cleaning carpets, however has the shortest run time. This is the default suction mode when the vacuum is turned ON.
·· Recommended for everyday cleaning. It’s great for hard floors, low pile carpets and area rugs. It balances power and run time.
· Recommended for the longest run time. It’s great for hard floors and offers the quietest sound.

Using the Parking Brake
Go to support.BISSELL.com for additional how-to videos.

1. The built-in brake helps prevent the machine from slipping on the floor when it is leaning against a wall.

2. To engage the brake, simply push the brake on the motorized foot forward.

3. To disengage the brake, pull it forward.

WARNING Do not use your vacuum until you are familiar with all instructions and operating procedures.
BISSELL.com 7

Attaching Tools for Hand Vac Use
Go to support.BISSELL.com for additional how-to videos.
Clean stairs or furniture easily with the tools provided. Pair your desired tool with the hand vacuum or Extension Wand. Go to support.BISSELL.com for tips on above floor cleaning tools.

1. To use as a hand vacuum, press the release button to disconnect it from the Extension Wand.
8 BISSELL.com

2. Attach your chosen tool.

3. Use the tool to clean furniture, stairs or other surfaces in your home.

Emptying the Dirt Tank
More of a video person? Go to support.BISSELL.com for additional how-to videos.

1. Turn OFF your machine. Remove the Dirt Tank from the hand vacuum by sliding the latch on the front of the tank.

2. Grab the top of the tank and pull up. This will activate a wiping feature to remove debris from the mesh filter screen.

3. Fully remove the separator from the tank and tap the mesh screen on the side of the trash bin.

2

1

4. Dump dirt from the tank into the trash bin.

5. Slide the separator back into the tank, ensuring the notch is seated into the tank correctly.

6. Put the whole tank into the hand vacuum by guiding the notched out area on the bottom of the tank onto the hook on the hand vacuum. Push into place.

Removing the Brush Roll
Go to support.BISSELL.com for a full list of maintenance and troubleshooting support.

1. Turn the machine OFF and press the Foot Release Button to disconnect the Motorized Floor Cleaning Foot from the Extension Wand.

2. With a flathead screwdriver or coin, twist the slot on the side of the foot clockwise and pull the Brush Roll out.

3. To replace, push the Brush Roll back in the chamber and twist counter-clockwise with a tool or coin to lock in place.

WARNING
» Before using your vacuum, make sure that the Dirt Tank is in locked position and that all filters, both pre and post-filters, are in place. DO NOT operate your vacuum without these filters.
BISSELL.com 9

Cleaning & Replacing the Filters
Go to support.BISSELL.com for tips on maintaining and replacing your vacuum filters.
Pre-Motor Filters
For best cleaning performance, always clean your pre-motor filter after each use.

1. To clean the pre-motor filter, turn OFF machine and remove Dirt Tank from the hand vacuum.

2. Pull filter from the top of the tank. Remove the filter from the filter frame housing. Tap the filter against the side of a trash bin to remove dust and debris.

3. To clean, rinse under warm water and squeeze to remove dirt. Lay out for 24 hours, until completely dry. Make sure to replace your filter into the frame with the tag side down (touching the frame) before using your machine.

Post-Motor Filter

1. To clean your post-motor filter, turn OFF machine and press the latch on the back of the hand vacuum.

2. Remove the post-motor filter from the vacuum.

3. If there’s debris on the filter, tap it on a trash bin and rinse under warm water. Let dry for at least 24 hours before putting it back in the vacuum and replacing the filter cover.

WARNING
» Do not use your vacuum until you are familiar with all instructions and operating procedures. » Before using your vacuum, make sure that the Dirt Tank is in locked position and that all filters, both pre and post-filters, are in
place. DO NOT operate your vacuum without these filters.
10 BISSELL.com

Troubleshooting
For a comprehensive walkthrough of your product and support visit support.BISSELL.com.
This guide has everything you need to get ready for first use, including setting up, using and maintaining your machine, but online you’ll find additional resources like tips and troubleshooting, videos, product registration, parts, and more.

Problem

Possible Cause Filters are dirty.

Vacuum won’t pick up dirt

There is a clog in the vacuum.

Dirt is escaping from the vacuum

Dirt Tank is not seated correctly. Dirt Tank is full. Filters are missing or dirty.
There is a clog in the vacuum.

Vacuum won’t charge

Wrong charger is being used.
Charger is not plugged into the machine properly.

Remedies
Remove and rinse pre-motor filters. Allow enough time for them to dry properly before reinserting. Remove and dust off post-motor filter.
Remove the foot and Extension Wand from the hand vacuum. Check for debris buildup or clogs in each of these sections. Clear any debris or clogs before reassembling.
Remove the tank and reseat properly.
Empty the tank.
Check to see if the pre- and post-motor filters are in place and clean, if necessary.
Remove the foot and Extension Wand from the hand vacuum. Check for debris buildup or clogs in each of these sections. Clear any debris or clogs before reassembling.
Use only the charger that comes with the machine.
Remove the charger and reinstall into the hand vacuum.

Errors

Cause: Suction motor fault.
Remedy: Turn machine OFF. Check and clean filters. Check and clean the machine of clogs. If this doesn’t solve the problem, contact Consumer Care.

Cause: Brush Roll stall.
Remedy: Turn machine OFF. Check and clean the Brush Roll of any clogs. Brush Roll can be removed for thorough cleaning (page 8). Turn machine ON.

Cause: Battery issue.
Remedy: Contact Consumer Care.

Air flow issue.
Remedy: Turn machine OFF. Check and clean filters. Check and clean the machine of clogs. If this doesn’t solve the problem, contact Consumer Care.

Warranty
2-Year limited warranty, may vary by state. Visit support.BISSELL.com or call 1-800-237-7691 for complete warranty information.
NOTICE Disconnecting the battery will destroy the appliance and invalidate the warranty.
BISSELL.com 11

We’re Waggin’ Our Tails!
BISSELL® proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL product, you help save pets, too. We’re proud to design products that help make pet messes, odors and pet homelessness disappear. Visit BISSELLsavespets.com to learn more.
But wait, there’s more!
Join us online for a complete guide to your new product, including troubleshooting, product registration, parts and more. Go to support.BISSELL.com.

REGISTER

INFO

VIDEOS

PARTS

SUPPORT

©2021 BISSELL Inc. All rights reserved. Part Number 1625990 11/20 RevB

Documents / Resources

Bissell 2288 Series Iconpet Cordless Vacuum Cleaner [pdf] User Guide
2288 Series, 2774 Series, Iconpet Cordless Vacuum Cleaner

Leave a comment

Your email address will not be published.