beamZ logo

Ref. nr.: 150.592beamZ BBP96 Battery Uplight Portable ParINSTRUCTION MANUAL

BBP96 Battery Uplight Portable Par

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to benefit fully from all features.
Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

  • Prior to using the product, please ask for advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear
    after a while.
  • The unit contains voltage-carrying parts. Therefore do NOT open the housing.
  • Do not place metal objects or pour liquids into the product. This may cause electrical shock and malfunction.
  • Do not place the product near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
  • The product is not suitable for continuous use.
  • Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
  • When unplugging the product from a mains outlet, always pull the plug, never the lead.
  • Do not plug or unplug the unit with wet hands.
  • If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
  • If the product is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the product on. Contact your dealer. Do NOT connect the product to a rheostat or dimmer.
  • To avoid fire and shock hazards, do not expose the product to rain and moisture.
  • All repairs should be carried out by a qualified technician only.
  • Connect the product to an earthed mains outlet (220240Vac/50Hz)  protected by a 10-16A fuse.
  • During a thunderstorm or if the product will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
  • If the product has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on.
  • Never use the product in humid rooms or outdoors.
  • During operation, the housing becomes very hot. Do not touch it during the operation and immediately after.
  • To prevent accidents in companies, you must follow the applicable guidelines and follow instructions.
  • Secure the product with an extra safety chain if the unit is ceiling mounted. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1-meter space on every side to ensure sufficient cooling.
  • This product contains high-intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
  • Do not repeatedly switch the product on and off. This shortens the lifetime.
  • Keep the unit out of the reach of children. Do not leave the unit unattended.
  • Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
  • Only operate the product with clean hands.
  • Do not force the controls.
  • If the product has fallen, always have it checked by a qualified technician before you switch the product on again.
  • Do not use chemicals to clean the unit. They damage the varnish. Only clean the product with a dry cloth.
  • Keep away from electronic equipment that may cause interference.
  • Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
  • Switch the product off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the product.
  • Make sure that the main lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
  • The mains voltage is 220-240Vac/50Hz. Check if the power outlet match. If you travel, make sure that the main voltage of the country is suitable for this product.
  • Keep the original packing material so that you can transport the product in safe conditions

caution This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.
WarningThis mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.
Warning DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.
The product has been certified CE. It is prohibited to make any changes to the product. They would invalidate the CE certificate and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.
Dustbin Icon Electric products must not be put into household waste. Please bring them to a recycling center. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.
Do not attempt to make any repairs yourself. This would invalidate your warranty. Do not make any changes to the product. This would also invalidate your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Beamz cannot be held responsible for personal injuries caused by the disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.


CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain the packing material for inspection if any parts appear damaged from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original
factory box and packing. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. Thearising condensation water might damage your device. Leave the device switched off until it has reached room temperature.


On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.
warning 2Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate electrical ground to avoid the risk of electrocution or fire.


Prior to operating the device off mains for the first time, the rechargeable battery must be fully charged.

  1. Switch on the device with the power switch. The operating time of the battery depends on the operating mode and the ambient temperature. After the operation, switch the device off.
  2. For charging the battery, connect the device to a power outlet via the enclosed adapter (12.6Vdc 2A). The device may be operated during the charging procedure.
  3. The device features a protective circuit for charging which prevents overload of the rechargeable battery. However, disconnect the device from the mains after charging. Otherwise, there will be a low current consumption even if the device is switched off.
  4. The device will heat up during charging; this is normal.
  5. To prevent damage to the battery by deep discharge, recharge a battery completely discharged as soon as possible. Do not store the unit with the battery completely discharged and regularly recharge the battery in case of long storage.


warning 2 CAUTION: Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealer!warning 2


  • The installation of the product has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harmful deformation.
  • The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
  • Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
  • The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
  • The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.
  • The fixture should be installed in the position where persons cannot reach and where persons may walk by or be seated.

warning 2 CAUTION: When installing the device, make sure there is no higher in inflammable material (decoration articles, etc.) in between a distance of min 0.5 meters.


beamZ BBP96 Battery Uplight Portable Par - fig

The control board offers several features: you can simply set the starting address, run the pre-programmed program or make a reset. The main menu is accessed by pressing the Mode button, and browse through the submenu by pressing Up or Down.
Press the Enter button in order to select the desired menu. You can change the selection by pressing Up or Down. Confirm every selection by pressing the Enter button.
You can leave every mode by pressing the Mode button. The functions provided are described later in this manual.


If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.

beamZ BBP96 Battery Uplight Portable Par - controller

5-pin XLR DMX Connectors.
Some manufacturers use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables into a 3-pin line a cable adaptor must be used. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion
Conductor 3-Pin XLR Female (Out) 5-Pin XLR Male (In)
Ground/Shield Pin 1 Pin 1
Data Compliment (- signal) Pin 2 Pin 2
Data True (+ signal) Pin 3 Pin 3
Not Used Pin 4 – Do Not Use
Not Used Pin 5 – Do Not Use

beamZ BBP96 Battery Uplight Portable Par - adaptor

At the last fixture, the DMX cable has to be terminated. Solder a 120 Ohm resistor between signal (-) and signal (+) into a 3-pin XLR connector and plug this into the DMX output of the last fixture in the chain.


The master/slave operation enables several same units can be controlled by one “master” unit. Connect the first unit “DMX OUT” socket with the second unit “DMX IN”, using a 3pin DMX Cable. Repeat this process with the third, fourth, etc. or see the above section “DMX-512 connection”. Choose the unit that will control all others and set this in master mode via the display. The other units that must react on the master, you must set in slave mode. The “Slave” will synchronously follow the “Master” .
Noted: Any unit can be the “Master” or “Slave”.


To switch off the lights: Press OFF on the remote control [1].
Manual Color Control: You can set R/G/B colors with the remote by pushing either the Red <R> button for red, the Green <G> button for green, the Blue <B> button for blue, the White <W> button for white, the Amber <A> button for Amber, the Uv <UV> button for UV [3].
Preset color mode: Press one of the nine preset colors on the remote control. [4]
Program: Press one of the four program buttons to choose between the different auto programs [5]. Speed can be changed with up and down button [1].
warning 2The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise, operation of the remote control is not possible.
If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press, the small bar with the groove to the right (1) and at the same time remove the battery support (2). For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.beamZ BBP96 Battery Uplight Portable Par - button

The unit can be used with wireless DMX. The wireless receiver module functions as a receiver and transmitter of a 2.4 GHz wireless signal. Switch DMX on wirelessly via the main menu (see menu structure, behind of the manual for more information).
Then establish a wireless connection with the Beamz BPP Wireless DMX Transmitter (154.077).
CAUTION! The BPP Wireless DMX Transmitter and unit must be connected on the same DMX Universe, you can check easily by the color of the LED indicator.

DMX Universe Colour DMX Channels
1 Red 1 ~ 512
2 Green 1 ~ 512
3 Yellow 1 ~ 512
4 Blue 1 ~ 512
5 Magenta 1 ~ 512
6 Cyan 1 ~ 512
7 White 1 ~ 512

beamZ BBP96 Battery Uplight Portable Par - connected


If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.
Procedure:beamZ BBP96 Battery Uplight Portable Par - fuse
Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.


The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause a greater accumulation of dirt on the unit’s optics.

  • Make sure the area below the installation place is free from unwanted persons during servicing
  • Housings, fixations and installations spots( ceiling, truss, suspensions) should be totally free from any deformation
  • The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected
  • In order to protect the fixture from overheating the cooling fans (if any) and ventilation openings should be cleaned monthly.
  • The interior of the fixture should be cleaned annually using a vacuum cleaner or air jet.
  • Clean with soft cloth using normal glass cleaning fluid.
  • Always dry the parts carefully.
  • Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.
    ATTENTION: We strongly recommend internal cleaning to be carried out by qualified worker!


DMX512  Shows  Sound  Colour  Set  HeIp 
A001Console andslave mode Auto ColourColor Jumping
Adjust the speed after press the ENTER (099)
Sound Model
Sound Control 1
Press the ENTER to adjust the
Custom Colour
Manual dimming
Y(A): 0-255
UV: 0255
DMX channel
Channel mode
Name: 6 Colour
Auto FadeColour gradient
Adjust the speed after press the ENTER (0-99)
Sound Mode2
Sound Control 2
Press the ENTER to adjust the
Static Colour
Choose static colour color 1-32
2.4G wireless
Wireless DMX
Version: V4.0
Auto SuddenColour Jumping Adjust the speed
after press the ENTER (099)
Sound Mode 3
Sound Control 3
Press the ENTER to adjust the
Infrared remote
control ON/OFF
DMX Channel:
Auto StrobeFull strobe
Adjust the speed after press the ENTER(0-99)
Sound Mode 4
Sound control 3
Press the ENTER to adjust the sensitivity (0-100)
Display backlight
Adjust the brightneof the display backlight 0-100%
Run Time:
W-Mode(Not available) LCD Close time
Backlight display
1). Open
2). 5S
3). 10S
4). 15S
5). 30S
User Time:
Fan speed
Fan speed selection1). Auto speed
2). Slow speed
3) Middle speed
4). Fast speed
Restore factory
White balance adjustment
Battery status
Background Colour


6 Channels

Channel Function Value Description



000-255 Red dimmer from dark to bright
2 000-255 Green dimmer from dark to bright
3 000-255 Blue dimmer from dark to bright
4 000-255 White dimmer from dark to bright
5 000-255 Amber dimmer from dark to bright
6 000-255 UV dimmer from dark to bright

10 Channels

Channel Function Value Description
1 Master dimmer 000-255 From dark to bright



000-255 Red dimmer from dark to bright
3 000-255 Green dimmer from dark to bright
4 000-255 Blue dimmer from dark to bright
5 000-255 White dimmer from dark to bright
6 000-255 Amber dimmer from dark to bright
7 000-255 UV dimmer from dark to bright
8 Strobe 000-255 Strobe from slow to fast








000-008 No function
009-050 Color selection controlled by channel 10
051-100 Color Gradual change
101-150 Color jumping
151-200 Color Pulse change
201-220 Sound 1
221-240 Sound 2
241-255 Sound 3
10 Program speed 000-255 Function speed from slow to fast


Rated voltage: AC100~240V 50/60Hz
Rated power: 72W
DMX Channels: 6 or 10 Channels
Function: DMX, Auto, Sound active, and Master-Slave.
Dimensions per unit : 135 x 135 x 200mm
Weight (per unit) : 2.87 kg
The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.
The products referred to in this manual conform to the European Community Directives to which they are subject:

  • CE SYMBOL Low Voltage (LVD) 2014/35/EU
  • Electromagnetic Compatibility (EMC) 2014/30/EU
  •  Restriction of Hazardous Substances (RoHS) 2011/65/EU

Specifications and design are subject to change without prior notice..
Copyright © 2017 by TRONIOS the Netherlands

Documents / Resources

beamZ BBP96 Battery Uplight Portable Par [pdf] Instruction Manual
BBP96, Battery Uplight Portable Par, Uplight Portable Par, Uplight Par, Par, BBP96


Leave a comment

Your email address will not be published. Required fields are marked *