Blustream Home . Blustream
blustream.co.uk
Blustream Home . Blustream
User Manual for BLUSTREAM models including: SW12USB USB 3.2 Gen2 10Gb Switcher, SW12USB, USB 3.2 Gen2 10Gb Switcher, Gen2 10Gb Switcher, 10Gb Switcher
SW12USB. Blustream
File Info : application/pdf, 15 Pages, 1.10MB
DocumentDocumentSW12USB User Manual SW12USB_Manual_REVA4 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. Safety And Performance Notice Do not substitute or use any other power supply other than the enclosed unit, or a Blustream approved replacement. Do not disassemble the unit for any reason. Doing so will void the manufacturer's warranty. SW12USB USER MANUAL Contents Introduction 03 Features 03 Panel Descriptions 04 USB Performance 04 General Purpose Input (GPI) Port 05 Web GUI 05 Web GUI Control - Control / Devices 06 Web GUI Control - Settings / Network 07 Web GUI Control - Upgrade / Admin 08 Telnet & RS-232 Control Ports 09 Application Diagram 10 Specifications 11 Package Contents 11 Maintenance 11 Certifications 12 Installer Notes 13-14 02 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk SW12USB USER MANUAL Introduction The SW12USB is a USB 3.2 Gen2 10Gb switcher, supporting 4 x USB devices that can be switched to 2 x USB-C host connections. The SW12USB supports auto switching between host devices using signal sense, or manually controlled via the front-panel push buttons, Web-GUI, TCP/IP, or RS-232 FEATURES: · USB 3.2 Gen2 switch allowing up to 4 x USB peripheral devices to connect to 2 x USB hosts* · Features 2 x USB-C and 2 x USB-A device inputs and 2 x USB-C hosts · USB 3.2 Gen2 connectivity with data transfer rate up to 10Gbps · Backwards compatible with USB 2.0 and 1.1 · Auto or manual switching · Plug-and-play with no drivers, downloads, or software required · Features 1 x GPI port for integration with 3rd party products · Features 802.3at PoE+ for powering of product from PoE+ network · Local 24v power supply input for when network switch does not support PoE+ · Web interface module for control and configuration of SW12USB · Control via front panel buttons, RS-232, or TCP/IP *Please note: the SW12USB does not pass DP ALt Mode video Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 03 Front Panel SW12USB USER MANUAL 1 2 3 4 5 6 7 8 1 Power LED indicator - Illuminates when the unit is powered 2 USB Host LED Indicator - Illuminates when the corresponding USB Host is selected 3 Auto Switching LED Indicator - Illuminates when auto switching mode is enabled 4 USB Host Input - USB-C to connect to USB Host device 5 Select Button - Press to toggle between USB Hosts. Press and hold for 3 seconds to enable / disable auto switching function 6 Reset Switch - Press to factory reset the unit 7 Upgrade Selection Switch - Select between Hub or MCU for firmware upgrade function 5 Upgrade Port - Micro USB for firmware upgrade function Rear Panel 1 2 3 4 5 6 1 USB-C Device Inputs - Connect to USB-C devices 2 USB-A Device Inputs - Connect to USB-A devices Please note: total USB Device (USB-C and USB-A) charging support = 5V 4A. Max output per port is 5V 1.7A. 3 GPI Port - General purpose input for triggering input change - see follow page for details 4 RS-232 Port - 3-pin Phoenix connector for control of the switcher from a PC or control processor 5 External IR Port - Connect Blustream 5V IR receiver, or control processor to control the switcher 6 Power Port - Use supplied Blustream 24V/1.25A DC adaptor to power the unit USB Performance The SW12USB is a USB 3.2 Gen2 USB switch with data transfer rate up to 10Gbps and backwards compatibility support for USB 2.0 and 1.1 devices. Please note that actual USB performance will be dependent on the following factors: · USB Host version and cable length / quality · USB Device version and cable length / quality It is possible for the SW12USB to limit the USB-A Device port speed from 10Gbps to 5Gbps to improve device compatibility via the Web GUI and API. The SW12USB does not pass DP Alt Mode video. 04 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk SW12USB USER MANUAL General Purpose Input (GPI) Port The General Purpose Input (GPI) Port can be used to trigger the Host input to change on the SW12USB. It has 3 modes of function and can be configured via the Web GUI. Pulse Mode: In Pulse Mode, when the GPI port receives a signal pulse (every high (1-12V) to low (Ground) voltage change), it triggers the SW12USB device to change Host inputs. Level Mode: In Level Mode, the SW12USB will trigger based on the voltage applied to the GPI port. The low level trigger and high level trigger can be specified between 0-12V. The SW12USB will switch to Host 1 when GPI voltage is greater than the High Level trigger level. The SW12USB will switch to Host 2 when GPI voltage is less than the Low Level trigger level. Contact Closure Mode: In Contact Closure Mode when GPI port is open circuit, the SW12USB will select Host 1. When GPI port is shorted to ground, the SW12USB will select Host 2. The SW12USB features an in-built web-GUI for control and configuration of the unit. By default the device is set to DHCP, however if a DHCP server (eg: network router) is not installed the device IP address will revert to below details: Default IP Address is: 192.168.0.200 Default Username is: blustream Default Password is: 1234 * Please note: Due to new UK cyber security requirements, the default password has been updated for the below firmware versions (and above) to default password: @Bls1234 SW12USB: firmware version: V1.3.0 onwards New password regulations requires new passwords being set for products to be a minimum of 8 characters and contain a minimum of: 1x uppercase letter, 1x lowercase letter, 1x symbol and 1x number. The device can also be accessed via its mDNS name which is defaulted to: http://SW12USB.local/ Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 05 SW12USB USER MANUAL Web-GUI - Control The Control tab of the web-GUI allows for a user to switch between Host 1 or Host 2. The Host labels cannot be assigned within the GUI as most control will either be carried out automatically, or via API command. The Auto functionality allows for the SW12USB to automatically switch over to a new Host being connected to the unit. Web-GUI - Devices The Devicves tab allows for control over power delivered to the devices connected, and if these need to be powered permanently, or only when there is a live Host connection available. Current and voltage being drawn is also reported within this tab for reference. The ports can be disabled by using the radial button next to each connection. The USB-A connections can have the amount of data limited between USB 3.2 Gen 1 (5Gbps - default)) or USB 3.2 Gen 2 (10Gbps). 06 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk SW12USB USER MANUAL Web-GUI - Settings The Settings tab allows for the configuration of the RS-232 terminal (HEX or ASCII communication, Baud Rate, Command Ending and a trigger command to be sent if the GPI is triggered). The GPI connection can also be configured from this tab, allowing for a trigger to be received by the SW12USB in Pulse Mode, Level Mode (with options for low and high voltages to be received), or Contact Closure Mode. The button on the fornt of the unit can also be enabled / disabled form this screen to stop users from pressing this to switch between Hosts. Web-GUI - Network Network settings for the TCP/IP port of the unit can be configured from this tab of the web-GUI. Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 07 SW12USB USER MANUAL Web-GUI - Upgrade The firmware of the MCU of the SW12USB is carried out from this tab of the user interface. Please see separate guide that is downloaded alongside the firmware files from the Blustream website for instructions of how to update the firmware of this unit, Web-GUI - Admin The Admin tab allows for the administrators username and password to be updated as required. Users can also be set up from this tab. 08 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk SW12USB USER MANUAL Telnet & RS-232 Control Ports The SW12USB can be controlled via a 3-pin phoenix to serial RS-232 cable, or via Telnet. The RS-232 communication settings and commands are as follows: Baud Rate: 57600 bps Data Bit: 8-bit Parity: None Stop Bit: 1-bit Flow Control: None RS-232 / TELNET COMMAND ?/HELP STATUS PON/OFF RESET HOST yy FR All SWITCH aa USBDP aa USBDPOUT yy ON/OFF GPI yy GPI LOW xx GPI HIGH xx FP LOCK ON/OFF NAME zz UG HUB yy SPEED yy RS232BAUD z RS232ON y:z:a NET DHCP ON/OFF NET TN 8000 ON/OFF NET TN ON/OFF NET MDNS ON/OFF NET IP xxx.xxx.xxx.xxx NET GW xxx.xxx.xxx.xxx NET SM xxx.xxx.xxx.xxx NET RB NET TN xxxx DESCRIPTION Print Help Information Print System Status And Port Status Set System Power On Or Off Reset System To Default Setting Type 'Yes' To Confirm, 'No' To Discard Within 30 Seconds Set Connect From Host:yy yy = 01 : Host1 yy = 02 : Host2 Set Switching To aa aa = AUTO: Auto Switching ON - Auto Mode aa = MAN: Auto Switching OFF - Manual Mode Set USB Device Power Mode aa = FH : Follow Host aa = ON : Always On Set USB Device Power Output yy = 00 : All Devices yy = 01-04 : Device1-4 Set GPI Mode yy = 00 : Pulse Mode yy = 01 : Level Mode yy = 02 : Contact Closure Mode Set The Low Level Voltage In The Level Mode xx Range 0~12000 Unit mV Set The High Level Voltage In The Level Mode xx Range 0~12000 Unit mV Set Front Panel Lock ON Or OFF Set Device Name zz Is New Device Name Select Hub Upgrade Note: All Connected Devices Will Lost. Switch The Host Or Reconnect The USB Cable It Will Be Returned To Normal yy = 01 : Hub1 yy = 02 : Hub2 Set Type-A Port Speed yy = 00 : Speed 5G yy = 01 : Speed 10G Set RS232 Baud Rate To xx z = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600 (Default), 7 115200 Send y Type Of Command a Stored In Local RS232 Whose Baud Rate Is z y = a ASCII, h HEX z = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600 (Default), 7 115200 a = RS232 Command Set Auto IP(DHCP) On Or Off Set Telnet Port 8000 On Or Off Set Telnet Port On Or Off Set mDNS On Or Off Set IP Address Set Gateway Address Set Subnet Mask Address Set Network Reboot And Apply New Config!!! Set Telnet Port Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 09 10 Example Schematic SW12USB USB Host LAPTOP PC www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk USB Host RS-232 USB Devices TCP/IP USB Devices MIC MOUSE WEB CAM KEYBOARD Control Processor SW12USB USER MANUAL Specifications · USB Device: 2 x USB Type A female, 2 x USB Type C female · USB Host: 2 x USB Type C female · GPI / RS-232 Serial Port: 1 x 4-pin Phoenix connector · TCP/IP Control: 1 x RJ45, female · Firmware Upgrade: 1 x Micro-USB · Dimensions (W x D x H): 150mm x 110mm x 23mm · Shipping Weight: 0.6kg · Operating Temperature: 32°F to 104°F (0°C to 40°C) · Storage Temperature: -4°F to 140°F (-20°C to 60°C) · Power Supply: 24V/1.25A DC, 4-pin DIN connector NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate. Package Contents · 1 x SW12USB · 1 x 24V/1.25A DC power supply · 1 x 3-pin phoenix to DB9 serial cable · 1 x Mounting kit · 1 x Quick Reference Card SW12USB USER MANUAL Maintenance Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit. Components inside this unit are not user serviceable. Do not remove the protective cover from the unit. Removing any panel from this product will invalidate the manufacturers warranty. Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 11 Certifications SW12USB USER MANUAL FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. CAUTION - changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CANADA, INDUSTRY CANADA (IC) NOTICES This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CORRECT DISPOSAL OF THIS PRODUCT This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. 12 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk Installer Notes SW12USB USER MANUAL Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 13 Installer Notes SW12USB USER MANUAL 14 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk www.blustream-us.com www.blustream.com.au www.blustream.co.uk