DS20U Series Quick Guide

More information on this product can be found at: http://bit.ly/DS20U

Product Overview

Hardware Installation

A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.

1. Unscrew the two screws of the chassis cover. Slide the cover backward and upwards.

The product’s color and specifications may vary from the actual shipping product.
B. HDD or SSD Installation

1. Unfasten the rack mount screw and remove the rack.
   
2. Place an HDD or SSD in the rack and secure it with two screws from each side.
   
3. Lay the HDD or SSD into its drive bay and push it gently to the right until it clicks into place. Refasten screws.

C. Memory Module Installation
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.

1. Locate the SO-DIMM slots on the motherboard.
2. Align the notch of the memory module with one of the relevant memory slots.
3. Gently insert the module into the slot at a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking mechanism.
   
5. Repeat the above steps to install an additional memory module, if required.

D. M.2 Device Installation

1. Locate the M.2 key slots on the motherboard.
2. Install the M.2 device into the M.2 slot and secure it with the screw.
   M.2 2242/2260/2280 M key slot

E. Complete

1. Please replace and affix the case cover with two screws. Turn your DS20U upside down.
2. Connect the power cord.
3. Complete.

Please press the “Del” key while booting to enter BIOS. Here, please load the optimized BIOS settings. Operation Position: Please make sure to use either the supplied feet or the VESA mount.

Safety Information

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries according to the manufacturer’s instructions.
All bundled parts, power cord included, shall not be used without this product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device meets the requirements for EU conformity in accordance with the currently valid EU directives.

Product Overview

Hardware Installation
A. Begin Installation 
For safety reasons, please ensure that the power cord is disconnected before opening the case.

1. Unscrew the two screws of the chassis cover. Slide the cover backward and upwards.

B. HDD or SSD Installation

1. Unfasten the rack mount screw and remove the rack.
2. Place the HDD or SSD in the rack and secure it with two screws from each side.
3. Lay the HDD or SSD into its drive bay and push it gently to the right until it clicks into place. Refasten screws.

The product’s color and specifications may vary from the actually
C. Memory Module Installation
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.

1. Locate the SO-DIMM slots on the motherboard.
2. Align the notch of the memory module with one of the relevant memory slots.
3. Gently insert the module into the slot at a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking mechanism.
5. Repeat the above steps to install an additional memory module, if required.

D. M.2 Device Installation

1. Locate the M.2 key slots on the motherboard.
2. Install the M.2 device into the M.2 slot and secure it with the screw.

E. Complete

1. Please replace and affix the case cover with two screws. Turn your DS20U upside down.
2. Connect the power cord.
3. Complete.

Please press the “Del” key while booting to enter BIOS. Here, please load the optimized BIOS settings. Operation Position: Please make sure to use either the supplied feet or the VESA mount.

Motherboard Illustration

Jumper Settings

J1: COM 2 Port

J2: USB 2.0 Connector

J3: AC Back Auto Power ON

J4: COM 1 & COM 2 Power Switch
COM PORT Pin 9 “Ring Indicator” (RI) configuration:

J5: VGA connector

J6: External Power SW & Clear CMOS

Documents / Resources

Baechler DS20U Series Shuttle Barebone PC [pdf] User Guide DS20U Series Shuttle Barebone PC, DS20U Series, Shuttle Barebone PC, Barebone PC, PC

References

• User Manual